Reduce the time required for ./configure to perform the needed
KABI checks by allowing kbuild to compile multiple test cases in
parallel. This was accomplished by splitting each test's source
code from the logic handling whether that code could be compiled
or not.
By introducing this split it's possible to minimize the number of
times kbuild needs to be invoked. As importantly, it means all of
the tests can be built in parallel. This does require a little extra
care since we expect some tests to fail, so the --keep-going (-k)
option must be provided otherwise some tests may not get compiled.
Furthermore, since a failure during the kbuild modpost phase will
result in an early exit; the final linking phase is limited to tests
which passed the initial compilation and produced an object file.
Once everything has been built the configure script proceeds as
previously. The only significant difference is that it now merely
needs to test for the existence of a .ko file to determine the
result of a given test. This vastly speeds up the entire process.
New test cases should use ZFS_LINUX_TEST_SRC to declare their test
source code and ZFS_LINUX_TEST_RESULT to check the result. All of
the existing kernel-*.m4 files have been updated accordingly, see
config/kernel-current-time.m4 for a basic example. The legacy
ZFS_LINUX_TRY_COMPILE macro has been kept to handle special cases
but it's use is not encouraged.
master (secs) patched (secs)
------------- ----------------
autogen.sh 61 68
configure 137 24 (~17% of current run time)
make -j $(nproc) 44 44
make rpms 287 150
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8547Closes#9132Closes#9341
Conflicts:
Makefile.am
config/kernel-fpu.m4
Commit f4af6bb783 which added support
for REQ_FAILFAST_MASK but the new autoconf test didn't use the same
preprocessor macro name as the code did.
The effect is that FAILFAST mode has not been enabled for ZoL in any
post-2.6.35 kernel.
Retire the HAVE_BIO_RW_FAILFAST interface used in pre-2.6.28 kernels.
Raise an error condition if the FAILFAST interface can't be detected.
Signed-off-by: Tim Chase <tim@onlight.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3386
Newer versions of gcc are getting smart enough to detect the sloppy
syntax used for the autoconf tests. It is now generating warnings
for unused/undeclared variables. Newer version of gcc even have
the -Wunused-but-set-variable option set by default. This isn't a
problem except when -Werror is set and they get promoted to an error.
In this case the autoconf test will return an incorrect result which
will result in a build failure latter on.
To handle this I'm tightening up many of the autoconf tests to
explicitly mark variables as unused to suppress the gcc warning.
Remember, all of the autoconf code can never actually be run we
just want to get a clean build error to detect which APIs are
available. Never using a variable is absolutely fine for this.
Closes#176
As of linux-2.6.36 the BIO_RW_FAILFAST and REQ_FAILFAST flags
have been unified under the REQ_* names. These flags always had
to be kept in-sync so this is a nice step forward, unfortunately
it means we need to be careful to only use the new unified flags
when the BIO_RW_* flags are not defined. Additional autoconf
checks were added for this and if it is ever unclear which method
to use no flags are set. This is safe but may result in longer
delays before a disk is failed.
Perferred interface for setting FAILFAST on a bio:
2.6.12-2.6.27: BIO_RW_FAILFAST
2.6.28-2.6.35: BIO_RW_FAILFAST_{DEV|TRANSPORT|DRIVER}
2.6.36-2.6.xx: REQ_FAILFAST_{DEV|TRANSPORT|DRIVER}
ZFS works best when it is notified as soon as possible when a device
failure occurs. This allows it to immediately start any recovery
actions which may be needed. In theory Linux supports a flag which
can be set on bio's called FAILFAST which provides this quick
notification by disabling the retry logic in the lower scsi layers.
That's the theory at least. In practice is turns out that while the
flag exists you oddly have to set it with the BIO_RW_AHEAD flag.
And even when it's set it you may get retries in the low level
drivers decides that's the right behavior, or if you don't get the
right error codes reported to the scsi midlayer.
Unfortunately, without additional kernels patchs there's not much
which can be done to improve this. Basically, this just means that
it may take 2-3 minutes before a ZFS is notified properly that a
device has failed. This can be improved and I suspect I'll be
submitting patches upstream to handle this.
