Adding O_DIRECT support to ZFS to bypass the ARC for writes/reads.
O_DIRECT support in ZFS will always ensure there is coherency between
buffered and O_DIRECT IO requests. This ensures that all IO requests,
whether buffered or direct, will see the same file contents at all
times. Just as in other FS's , O_DIRECT does not imply O_SYNC. While
data is written directly to VDEV disks, metadata will not be synced
until the associated TXG is synced.
For both O_DIRECT read and write request the offset and request sizes,
at a minimum, must be PAGE_SIZE aligned. In the event they are not,
then EINVAL is returned unless the direct property is set to always (see
below).
For O_DIRECT writes:
The request also must be block aligned (recordsize) or the write
request will take the normal (buffered) write path. In the event that
request is block aligned and a cached copy of the buffer in the ARC,
then it will be discarded from the ARC forcing all further reads to
retrieve the data from disk.
For O_DIRECT reads:
The only alignment restrictions are PAGE_SIZE alignment. In the event
that the requested data is in buffered (in the ARC) it will just be
copied from the ARC into the user buffer.
For both O_DIRECT writes and reads the O_DIRECT flag will be ignored in
the event that file contents are mmap'ed. In this case, all requests
that are at least PAGE_SIZE aligned will just fall back to the buffered
paths. If the request however is not PAGE_SIZE aligned, EINVAL will
be returned as always regardless if the file's contents are mmap'ed.
Since O_DIRECT writes go through the normal ZIO pipeline, the
following operations are supported just as with normal buffered writes:
Checksum
Compression
Encryption
Erasure Coding
There is one caveat for the data integrity of O_DIRECT writes that is
distinct for each of the OS's supported by ZFS.
FreeBSD - FreeBSD is able to place user pages under write protection so
any data in the user buffers and written directly down to the
VDEV disks is guaranteed to not change. There is no concern
with data integrity and O_DIRECT writes.
Linux - Linux is not able to place anonymous user pages under write
protection. Because of this, if the user decides to manipulate
the page contents while the write operation is occurring, data
integrity can not be guaranteed. However, there is a module
parameter `zfs_vdev_direct_write_verify` that controls the
if a O_DIRECT writes that can occur to a top-level VDEV before
a checksum verify is run before the contents of the I/O buffer
are committed to disk. In the event of a checksum verification
failure the write will return EIO. The number of O_DIRECT write
checksum verification errors can be observed by doing
`zpool status -d`, which will list all verification errors that
have occurred on a top-level VDEV. Along with `zpool status`, a
ZED event will be issues as `dio_verify` when a checksum
verification error occurs.
ZVOLs and dedup is not currently supported with Direct I/O.
A new dataset property `direct` has been added with the following 3
allowable values:
disabled - Accepts O_DIRECT flag, but silently ignores it and treats
the request as a buffered IO request.
standard - Follows the alignment restrictions outlined above for
write/read IO requests when the O_DIRECT flag is used.
always - Treats every write/read IO request as though it passed
O_DIRECT and will do O_DIRECT if the alignment restrictions
are met otherwise will redirect through the ARC. This
property will not allow a request to fail.
There is also a module parameter zfs_dio_enabled that can be used to
force all reads and writes through the ARC. By setting this module
parameter to 0, it mimics as if the direct dataset property is set to
disabled.
Reviewed-by: Brian Behlendorf <behlendorf@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Co-authored-by: Matt Macy <mmacy@FreeBSD.org>
Co-authored-by: Brian Behlendorf <behlendorf@llnl.gov>
Closes#10018
This is just a very small attempt to make it more obvious that these
flags aren't optional for libzpool-using programs, by not making it seem
like there's an option to say "well, I don't _want_ to force debugging".
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Issue #16476Closes#16477
Removing the platform #ifdefs from shared headers in favour of
per-platform headers. Makes abd_t much leaner, among other things.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16253
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16400
Since the change to folios it has just been a wrapper anyway. Linux has
removed their wrapper, so we add one.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16400
Detect it, and use a macro to make sure we always match the prototype.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16400
It's no longer available directly on the request queue, but its easy to
get from the attached disk.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16400
In 6.11 struct queue_limits gains a 'features' field, where, among other
things, flush and write-cache are enabled. Detect it and use it.
Along the way, the blk_queue_set_write_cache() compat wrapper gets a
little cleanup. Since both flags are alway set together, its now a
single bool. Also the very very ancient version that sets q->flush_flags
directly couldn't actually turn it off, so I've fixed that. Not that we
use it, but still.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16400
-shared was hardcoded, so when building with --disable-shared it amounts
to trying to do shared linkage against static libs, which naturally
fails.
The fix is straightforward; just don't hardcode it. libtool will work
out what to do.
Sponsored-by: https://despairlabs.com/sponsor/
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#16427
Changed zfs_k(un)map_atomic to zfs_k(un)map_local
Signed-off-by: Jason Lee <jasonlee@lanl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
This helper was introduced long ago, in 5.16. Since 6.10, bd_inode no
longer exists, but the helper has been updated, so detect it and use it
in all versions where it is available.
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Linux has started moving to a model where instead of applying block
queue limits through individual modification functions, a complete
limits structure is built up and applied atomically, either when the
block device or open, or some time afterwards. As of 6.10 this
transition appears only partly completed.
This commit matches that model within OpenZFS in a way that should work
for past and future kernels. We set up a queue limits structure with any
limits that have had their modification functions removed. For newer
kernels that can have limits applied at block device open
(HAVE_BLK_ALLOC_DISK_2ARG), we have a conversion function to turn the
OpenZFS queue limits structure into Linux's queue_limits structure,
which can then be passed in. For older kernels, we provide an
application function that just calls the old functions for each limit in
the structure.
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Artix Linux is systemd free distribution based on Arch Linux, with
openrc dinit runit s6 as init alternatives. This patch will make
init scripts installation work the way Gentoo Linux with openrc.
The scripts tweaking for other init will be left to packager.
Signed-off-by: Yongming Zhao <ming.zym@gmail.com>
Reviewed-by: Rob Norris <robn@despairlabs.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Since Linux 6.7 the kernel has defined intptr_t. Clang has
-Wtypedef-redefinition by default, which causes the build to fail
because we also have a typedef for intptr_t.
Since its better to use the kernel's if it exists, detect it and skip
our own.
Sponsored-by: https://despairlabs.com/sponsor/
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#16201
libunwind seems to do a better job of resolving a symbols than
backtrace(), and is also useful on platforms that don't have backtrace()
(eg musl). If it's available, use it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16140
Adds a check for the backtrace() function. If available, uses it to show
a stack backtrace in the assertion output.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16140
Makes it much easier to see what thing complained.
Getting thread id, program name and thread name vary wildly between
Linux and FreeBSD, so those are set up in macros. pthread_getname_np()
did not appear in musl until very recently, but the same info has always
been available via prctl(PR_GET_NAME), so we use that instead.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16140
The "not found" path is attempting to clear SOMELIB_CFLAGS and
SOMELIB_LIBS by resetting them in AC_SUBST(). However, the second arg to
AC_SUBST is expanded in autoconf with `m4_ifvaln([$2], [[$1]=$2])`,
which is defined as "if the first arg is non-empty". The m4 "empty"
construction is [], therefore, the existing AC_SUBST calls never modify
the variables at all.
The effect of this is that leftovers from the library test can leak out.
At least, if a library header is found in the first stage, but the
library itself is not, -lsomelib is added to SOMELIB_LIBS and further
tests done. If that library is not found, SOMELIB_LIBS will not be
cleared.
For most of our library tests this hasn't been a problem, as they're
either always found properly via pkg-config or set directly, or the
calling test immediately aborts configure. For an optional dependency
however, an apparent "partial" result where the header is found but no
corresponding library causes link errors later.
I think a complete fix should probably not be setting SOMELIB_xxx until
the final result is known, but for now, adjusting the AC_SUBST calls to
explictly set the empty shell string (which is not "empty" to m4) at
least restores the intent.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16140
As for python-3.12 the distutils package has been deprecated.
The latest ax_python_devel.m4 macro from the autoconf archive
has been updated accordingly so let's pull in the new version.
We can also drop the changes made to our customized version
to continue if the development version is not installed since
this functionality has been included upstream.
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#16126Closes#16129
We recover the scope of $(SUBSTFILES) to explicitly control what files
are being generated from the corresponding .in.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Benda Xu <orv@debian.org>
Closes#15980
Let Debian use the sysv-rc variant of the script, even when OpenRC is
installed. Unlike on Gentoo, OpenRC on Debian consumes both the
sysv-rc scripts and OpenRC ones. ZFS initscripts on Debian should be
the sysv-rc version to provide most compatibility and to integrate
with the rest of initscripts for dependency tracking.
Restrict the substitution in the Makefile to the dedicated list.
This construct is inspired by Mo Zhou's detection of the execution
shell and follows the strategy of Peter in 6ef28c526b.
As of 2024, the initscripts are mostly relevant on Debian, Gentoo and
their derivatives.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Benda Xu <orv@debian.org>
Issue #8063
Issue #8204
Issue #8359Closes#15977
After 06e25f9c4, the discard issuing code was organised such that if
requesting an async discard or secure erase failed before the IO was
issued (that is, calling __blkdev_issue_discard() returned an error),
the failed zio would never be executed, resulting in txg_sync hanging
forever waiting for IO to finish.
This commit fixes that by immediately executing a failed zio on error.
To handle the successful synchronous op case, we fake an async op by,
when not using an asynchronous submission method, queuing the successful
result zio as part of the discard handler.
Since it was hard to understand the differences between discard and
secure erase, and sync and async, across different kernel versions, I've
commented and reorganised the code a bit to try and make everything more
contained and linear.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16070
99741bde5 accesses a cached blk-mq hardware context through the mq_hctx
field of struct request. However, this field did not exist until 5.0.
Before that, the private function blk_mq_map_queue() was used to dig it
out of broader queue context. This commit detects this situation, and
handles it with a poor-man's simulation of that function.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16069
There's an extra nullable arg for queue limits. Detect it, and set it to
NULL. Similar change for blk_mq_alloc_disk(), now three args, same
treatment.
Error return now has error encoded in the return, so detect with
IS_ERR() and explicitly NULL our own return.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16027Closes#16033
bdev_open_by_path() is replaced by bdev_file_open_by_path(), which
returns a plain old struct file*. Release function is gone entirely; the
regular file release function fput() will take care of the bdev
specifics.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16027Closes#16033
In v5.18 `filemap_range_has_page` moved to `pagemap.h`
`pagemap.h` has been around since 3.10 so just include both
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rob Norris <robn@despairlabs.com>
Signed-off-by: Robert Evans <evansr@google.com>
Closes#16034
Before 5.4 we have to do a little math.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Closes#15533Closes#15588
Linux 6.8 removes generic_copy_file_range(), which had been reduced to a
simple wrapper around splice_copy_file_range(). Detect that function
directly and use it if generic_ is not available.
Sponsored-by: https://despairlabs.com/sponsor/
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#15930Closes#15931
-Wformat-truncation looks for places where the return code of snprintf()
is unchecked and the provided buffer might be too short. This is based
on a heuristic that can change between compiler versions.
It has been seen to get this wrong in ddt_object_name(), leading to
DDT_NAMELEN being increased somewhat arbitrarily.
There's no good reason to have this warning enabled, so here we disable
it everywhere. Truncation may be undesirable, but snprintf() is
guaranteed to emit a trailing null, so at worst we get a short string,
not a buffer overrun.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#15908
On Linux, ZFS uses blkdev_issue_discard in vdev_disk_io_trim to issue
trim command which is synchronous.
This commit updates vdev_disk_io_trim to use __blkdev_issue_discard,
which is asynchronous. Unfortunately there isn't any asynchronous
version for blkdev_issue_secure_erase, so performance of secure trim
will still suffer.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15843
struct mnt_idmap no longer has a struct user_namespace within it. Work
around this by creating a temporary with the copy of the map we need
taken from the idmap.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Youzhong Yang <yyang@mathworks.com>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#15805
The name inode_permission is now defined in the kernel. Rename ours to
test_permission, in line with most of our other tests.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#15805
Linux has removed strlcpy in favour of strscpy. This implements a
fallback implementation of strlcpy for this case.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#15805
blkdev_get_by_path() and blkdev_put() have been replaced by
bdev_open_by_path() and bdev_release(), which return a "handle" object
with the bdev object itself inside.
This adds detection for the new functions, and macros to handle the old
and new forms consistently.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#15805
The kernel is now being compiled with -Wmissing-prototypes. Most of our
test stub functions had no prototype, and failed to compile. Since they
don't need to be visible anywhere else, just make them all static.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#15805
The LLVM/Clang developers pointed out that using the CPP to detect use
of functions that our QA policies prohibit risks invoking undefined
behavior. To resolve this, we configure CodeQL to detect forbidden
function usage.
Note that cpp in the context of CodeQL refers to C/C++, rather than the
C PreProcessor, which C++ also uses. It really should have been written
cxx, but that ship sailed a long time ago. This misuse of the term cpp
is retained in the CodeQL configuration for consistency with upstream
CodeQL.
As a side benefit, verbose make no longer is a wall of text showing a
bunch of CPP macros, which can make debugging slightly easier.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#15819Closes#14134
When building (s)rpm files through the Makefile, a directory structure
is created in /tmp to hold the various files.
In case the user running the command has overridden some of the RPM path
settings through their user profile (for example in `~/.rpmmacros`),
these paths do not line up with the configuration, and the build fails.
Make sure all paths used are properly defined.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ralf Ertzinger <ralf@skytale.net>
Closes#15756
This patch adds check for `kernel_neon_*` symbols on arm and arm64
platforms to address the following issues:
1. Linux 6.2+ on arm64 has exported them with `EXPORT_SYMBOL_GPL`, so
license compatibility must be checked before use.
2. On both arm and arm64, the definitions of these symbols are guarded
by `CONFIG_KERNEL_MODE_NEON`, but their declarations are still
present. Checking in configuration phase only leads to MODPOST
errors (undefined references).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Shengqi Chen <harry-chen@outlook.com>
Closes#15711Closes#14555Closes: #15401
6.7 changes the shrinker API such that shrinkers must be allocated
dynamically by the kernel. To accomodate this, this commit reworks
spl_register_shrinker() to do something similar against earlier kernels.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://github.com/sponsors/robnCloses#15681
In 6.7 the superblock shrinker member s_shrink has changed from being an
embedded struct to a pointer. Detect this, and don't take a reference if
it already is one.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://github.com/sponsors/robnCloses#15681
6.6 made i_ctime inaccessible; 6.7 has done the same for i_atime and
i_mtime. This extends the method used for ctime in b37f29341 to atime
and mtime as well.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://github.com/sponsors/robnCloses#15681
6.7 changed the names of the time members in struct inode, so we can't
assign back to it because we don't know its name. In practice this
doesn't matter though - if we're missing current_time(), then we must be
on <4.9, and we know our fallback will need to return timespec.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://github.com/sponsors/robnCloses#15681
Since Linux 6.2, the implementation of flush_dcache_page on riscv
references GPL-only symbol `PageHuge`, breaking the build of zfs.
This patch uses existing mechanism to override flush_dcache_page,
removing the call to `PageHuge`. According to comments in kernel,
it is only used to do some check against HugeTLB pages, which only
exist in userspace. ZFS uses flush_dcache_page only on kernel pages,
thus this patch will not introduce any behaviour change.
See also: torvalds/linux@d33deda, openzfs/zfs@589f59b
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Shengqi Chen <harry-chen@outlook.com>
Closes#14974Closes#15627
Check for the existence of execvpe(3) and only provide the FreeBSD
compat version if required.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#15609
With Linux v6.6.x and clang 16, a configure step fails on a warning that
later results in an error while building, due to 'ts' being
uninitialized. Add a trivial initialization to silence the warning.
Signed-off-by: Jaron Kent-Dobias <jaron@kent-dobias.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Followup e69ade32e1 by adding Gentoo's
bash completion path.
We should probably consider using/honouring the standard --with-bashcompletiondir
autoconf option as well, but that's something to do later.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Umer Saleem <usaleem@ixsystems.com>
Signed-off-by: Sam James <sam@gentoo.org>
Closes#15372
The recent patch to change the bash completion install location based
on the Distribution, ignored that it should still be possible to
create RPMs on Debian derived systems. Additionally `make deb` itself
creates RPMs and converts them via `alien`.
This patch adds the bashcompletiondir variable to the rpm defines and
uses this for the location, where to get the bash completion file.
It still changes the location on Debian/Ubuntu systems in the final
packages from /etc/bash_completion.d to
/usr/share/bash-completion/completions
Fixes: e69ade32e1
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Stoiko Ivanov <s.ivanov@proxmox.com>
Closes#15355Closes#15365
Certain Linux distributions (Debian/Ubuntu at least) expect
bash-completion snippets to be installed in
/usr/share/bash-completion/completions instead of
/etc/bash_completion.d.
This patch sets the bashcompletiondir variable based on the vendor,
inspired by similar settings for initdir and initconfdir.
It seems that commit 612b8dff5b
caused the file to be installed in the first-place (thus the error
when building debian packages only became apparent when testing a
2.2.0-rc4 build)
The change only sets the variable in Makefile context - the
rpm/zfs.spec.in file has the path hardcoded as
%{_sysconfdir}/bash_completion.d/zfs, but since running
```
./configure --sysconfdir=/myetc ; make rpm
```
also results in all relevant files to be installed in /etc instead of
/myetc I assume this can remain as is.
Reviewed-by: Umer Saleem <usaleem@ixsystems.com>
Signed-off-by: Stoiko Ivanov <s.ivanov@proxmox.com>
Closes#15304
