This adds a new test to measure ZIL performance.
- Adds the ability to induce IO delays with zinject
- Adds a new variable (PERF_NTHREADS_PER_FS) to allow fio threads to
be distributed to individual file systems as opposed to all IO going
to one, as happens elsewhere.
- Refactoring of do_fio_run
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: John Wren Kennedy <jwk404@gmail.com>
OpenZFS-issue: https://www.illumos.org/issues/9082
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/634
External-issue: DLPX-48625
Closes#7491
OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1ebCloses#6900
Most kshlib files are imported by other scripts
and do not have a shebang at the top of their files.
Make all kshlib follow this convention.
Remove shebangs from cfg files as well.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Close#7406
Due to zpool create auto-partioning in Linux (i.e. sdb1),
certain utilities need to use the parition (sdb1) while
others use the whole disk name (sdb).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#6939Closes#7261
Some usage patterns like send/recv of replication streams can
produce a large number of events. In such a case, the current
all-syslog.sh zedlet will hold up to its name, and flood the
logs with mostly redundant information. Two mitigate this
situation, this changeset introduces to new variables
ZED_SYSLOG_SUBCLASS_INCLUDE and ZED_SYSLOG_SUBCLASS_EXCLUDE
to zed.rc that give more control over which event classes end
up in the syslog.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Daniel Kobras <d.kobras@science-computing.de>
Closes#6886Closes#7260
Datasets can be busy when calling zfs destroy. Introduce
a helper function to destroy datasets and use it to destroy
datasets in zfs_allow_004_pos, zfs_promote_008_pos, and
zfs_destroy_002_pos.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#7224Closes#7246Closes#7249Closes#7267
Prevent false positives when running the zfs_share_* test
cases due to leftover stale /var/lib/nfs/etab entries. When
starting the test group re-synchronize the /var/lib/nfs/etab
file with /etc/exports. At this point in the testing there
will be no additional `zfs share` entries to add.
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7226
* Add a zed script to kick off a scrub after a resilver. The script is
disabled by default.
* Add a optional $PATH (-P) option to zed to allow it to use a custom
$PATH for its zedlets. This is needed when you're running zed under
the ZTS in a local workspace.
* Update test scripts to not copy in all-debug.sh and all-syslog.sh by
default. They can be optionally copied in as part of zed_setup().
These scripts slow down zed considerably under heavy events loads and
can cause events to be dropped or their delivery delayed. This was
causing some sporadic failures in the 'fault' tests.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#4662Closes#7086
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Don Brady <don.brady@delphix.com>
Ported-by: John Kennedy <john.kennedy@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/7431
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/dfc11533
Porting Notes:
* The CLI long option arguments for '-t' and '-m' don't parse on linux
* Switched from kmem_alloc to vmem_alloc in zcp_lua_alloc
* Lua implementation is built as its own module (zlua.ko)
* Lua headers consumed directly by zfs code moved to 'include/sys/lua/'
* There is no native setjmp/longjump available in stock Linux kernel.
Brought over implementations from illumos and FreeBSD
* The get_temporary_prop() was adapted due to VFS platform differences
* Use of inline functions in lua parser to reduce stack usage per C call
* Skip some ZFS Test Suite ZCP tests on sparc64 to avoid stack overflow
* Teach ZED to handle spares usingi the configured ashift: if the zpool
'ashift' property is set then ZED should use its value when kicking
in a hotspare; with this change 512e disks can be used as spares
for VDEVs that were created with ashift=9, even if ZFS natively
detects them as 4K block devices.
* Introduce an additional auto_spare test case which verifies that in
the face of multiple device failures an appropiate number of spares
are kicked in.
* Fix zed_stop() in "libtest.shlib" which did not correctly wait the
target pid.
* Fix ZED crashing on startup caused by a race condition in libzfs
when used in multi-threaded context.
* Convert ZED over to using the tpool library which is already present
in the Illumos FMA code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2562Closes#6858
Added -n flag to zpool reopen that allows a running scrub
operation to continue if there is a device with Dirty Time Log.
By default if a component device has a DTL and zpool reopen
is executed all running scan operations will be restarted.
Added functional tests for `zpool reopen`
Tests covers following scenarios:
* `zpool reopen` without arguments,
* `zpool reopen` with pool name as argument,
* `zpool reopen` while scrubbing,
* `zpool reopen -n` while scrubbing,
* `zpool reopen -n` while resilvering,
* `zpool reopen` with bad arguments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Closes#6076Closes#6746
The ZED is expected to automatically kick in a hot spare device
when there's one available in the pool and a sufficient number of
read errors have been encountered. Use zinject to simulate the
failure condition and verify the hot spare is used.
auto_spare_001_pos.ksh: read IO errors, the vdev is FAULTED
auto_spare_002_pos.ksh: read CHECKSUM errors, the vdev is DEGRADE
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: David Quigley <david.quigley@intel.com>
Closes#6280
History commands and events were being suppressed for the
'zpool create' command since the history object did not
yet exist. Create the object earlier so this history
doesn't get lost.
Split the pool_destroy event in to pool_destroy and
pool_export so they may be distinguished.
Updated events_001_pos and events_002_pos test cases. They
now check for the expected history events and were reworked
to be more reliable.
Reviewed-by: Nathaniel Clark <nathaniel.l.clark@intel.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6712Closes#6486
The chattr cleanup step may fail to delete the user if there is still
an active process running as that user. Retry the userdel when this
occurs to eliminate spurious false positves.
ERROR: userdel quser1 exited 8
userdel: user quser1 is currently used by process 26814
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6749
The portion of the zvol_replay_write() handler responsible for
replaying indirect log records for some reason never existed.
As a result indirect log records were not being correctly replayed.
This went largely unnoticed since the majority of zvol log records
were of the type WR_COPIED or WR_NEED_COPY prior to OpenZFS 7578.
This patch updates zvol_replay_write() to correctly handle these
log records and adds a new test case which verifies volume replay
to prevent any regression. The existing test case which verified
replay on filesystem was renamed slog_replay_fs.ksh for clarity.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6603Closes#6615
At import time spa_import() calls zvol_create_minors() directly: with
the current implementation we have no way to avoid device node
creation when volmode=none.
Fix this by enforcing volmode=none directly in zvol_alloc().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6426
If we are in the middle of an incremental 'zfs receive', the child
.../%recv will exist. If we run 'zfs promote' .../%recv, it will "work",
but then zfs gets confused about the status of the new dataset.
Attempting to do this promote should be an error.
Similarly renaming .../%recv datasets should not be allowed.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#4843Closes#6339
This change allows mountpoint_003_pos and send-c_props
to run on Linux kernels that do not support mandatory
locking. Linux kernel versions greater than or equal to
4.4 no longer support mandatory locking and the test
suite will now account for that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6346Closes#6347Closes#6362
Add multihost=on|off pool property to control MMP. When enabled
a new thread writes uberblocks to the last slot in each label, at a
set frequency, to indicate to other hosts the pool is actively imported.
These uberblocks are the last synced uberblock with an updated
timestamp. Property defaults to off.
During tryimport, find the "best" uberblock (newest txg and timestamp)
repeatedly, checking for change in the found uberblock. Include the
results of the activity test in the config returned by tryimport.
These results are reported to user in "zpool import".
Allow the user to control the period between MMP writes, and the
duration of the activity test on import, via a new module parameter
zfs_multihost_interval. The period is specified in milliseconds. The
activity test duration is calculated from this value, and from the
mmp_delay in the "best" uberblock found initially.
Add a kstat interface to export statistics about Multiple Modifier
Protection (MMP) updates. Include the last synced txg number, the
timestamp, the delay since the last MMP update, the VDEV GUID, the VDEV
label that received the last MMP update, and the VDEV path. Abbreviated
output below.
$ cat /proc/spl/kstat/zfs/mypool/multihost
31 0 0x01 10 880 105092382393521 105144180101111
txg timestamp mmp_delay vdev_guid vdev_label vdev_path
20468 261337 250274925 68396651780 3 /dev/sda
20468 261339 252023374 6267402363293 1 /dev/sdc
20468 261340 252000858 6698080955233 1 /dev/sdx
20468 261341 251980635 783892869810 2 /dev/sdy
20468 261342 253385953 8923255792467 3 /dev/sdd
20468 261344 253336622 042125143176 0 /dev/sdab
20468 261345 253310522 1200778101278 2 /dev/sde
20468 261346 253286429 0950576198362 2 /dev/sdt
20468 261347 253261545 96209817917 3 /dev/sds
20468 261349 253238188 8555725937673 3 /dev/sdb
Add a new tunable zfs_multihost_history to specify the number of MMP
updates to store history for. By default it is set to zero meaning that
no MMP statistics are stored.
When using ztest to generate activity, for automated tests of the MMP
function, some test functions interfere with the test. For example, the
pool is exported to run zdb and then imported again. Add a new ztest
function, "-M", to alter ztest behavior to prevent this.
Add new tests to verify the new functionality. Tests provided by
Giuseppe Di Natale.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#745Closes#6279
The volmode property may be set to control the visibility of ZVOL
block devices.
This allow switching ZVOL between three modes:
full - existing fully functional behaviour (default)
dev - hide partitions on ZVOL block devices
none - not exposing volumes outside ZFS
Additionally the new zvol_volmode module parameter can be used to
control the default behaviour.
This functionality can be used, for instance, on "backup" pools to
avoid cluttering /dev with unneeded zd* devices.
Original-patch-by: mav <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
FreeBSD-commit: https://github.com/freebsd/freebsd/commit/dd28e6bbCloses#1796Closes#3438Closes#6233
Currently, there is no way to pause a scrub. Pausing may
be useful when the pool is busy with other I/O to preserve
bandwidth.
This patch adds the ability to pause and resume scrubbing.
This is achieved by maintaining a persistent on-disk scrub state.
While the state is 'paused' we do not scrub any more blocks.
We do however perform regular scan housekeeping such as
freeing async destroyed and deadlist blocks while paused.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Serapheim Dimitropoulos <serapheimd@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6167
The log function log_must_busy was added in commit e623aea2 for
this purpose. Update destroy_pool to use it.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6217
* events_001_pos - Verify the expected events are generated when
invoking the various zpool sub-commands. These events must
appear in `zpool event` and be consumed by the ZED.
* events_002_pos - Verify the ZED consumes events which were
generated while it wasn't running when it is started.
Additionally, verify that events are only processed once.
As part of this change the default.cfg used by the test suite
was changed to a default.cfg.in file. This was needed so the
install location of all zed scripts, not only the enabled ones,
could be reliably determined.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6128
Enable most of the remaining test cases which were previously
disabled. The required fixes are as follows:
* cache_001_pos - No changes required.
* cache_010_neg - Updated to use losetup under Linux. Loopback
cache devices are allowed, ZVOLs as cache devices are not.
Disabled until all the builders pass reliably.
* cachefile_001_pos, cachefile_002_pos, cachefile_003_pos,
cachefile_004_pos - Set set_device_dir path in cachefile.cfg,
updated CPATH1 and CPATH2 to reference unique files.
* zfs_clone_005_pos - Wait for udev to create volumes.
* zfs_mount_007_pos - Updated mount options to expected Linux names.
* zfs_mount_009_neg, zfs_mount_all_001_pos - No changes required.
* zfs_unmount_005_pos, zfs_unmount_009_pos, zfs_unmount_all_001_pos -
Updated to expect -f to not unmount busy mount points under Linux.
* rsend_019_pos - Observed to occasionally take a long time on both
32-bit systems and the kmemleak builder.
* zfs_written_property_001_pos - Switched sync(1) to sync_pool.
* devices_001_pos, devices_002_neg - Updated create_dev_file() helper
for Linux.
* exec_002_neg.ksh - Fixed mmap_exec.c to preserve errno. Updated
test case to expect EPERM from Linux as described by mmap(2).
* grow_pool_001_pos - Adding missing setup.ksh and cleanup.ksh
scripts from OpenZFS.
* grow_replicas_001_pos.ksh - Added missing $SLICE_* variables.
* history_004_pos, history_006_neg, history_008_pos - Fixed by
previous commits and were not enabled. No changes required.
* zfs_allow_010_pos - Added missing spaces after assorted zfs
commands in delegate_common.kshlib.
* inuse_* - Illumos dump device tests skipped. Remaining test
cases updated to correctly create required partitions.
* large_files_001_pos - Fixed largest_file.c to accept EINVAL
as well as EFBIG as described in write(2).
* link_count_001 - Added nproc to required commands.
* umountall_001 - Updated to use umount -a.
* online_offline_001_* - Pull in OpenZFS change to file_trunc.c
to make the '-c 0' option run the test in a loop. Included
online_offline.cfg file in all test cases.
* rename_dirs_001_pos - Updated to use the rename_dir test binary,
pkill restricted to exact matches and total runtime reduced.
* slog_013_neg, write_dirs_002_pos - No changes required.
* slog_013_pos.ksh - Updated to use losetup under Linux.
* slog_014_pos.ksh - ZED will not be running, manually degrade
the damaged vdev as expected.
* nopwrite_varying_compression, nopwrite_volume - Forced pool
sync with sync_pool to ensure up to date property values.
* Fixed typos in ZED log messages. Refactored zed_* helper
functions to resolve all-syslog exit=1 errors in zedlog.
* zfs_copies_005_neg, zfs_get_004_pos, zpool_add_004_pos,
zpool_destroy_001_pos, largest_pool_001_pos, clone_001_pos.ksh,
clone_001_pos, - Skip until layering pools on zvols is solid.
* largest_pool_001_pos - Limited to 7eb pool, maximum
supported size in 8eb-1 on Linux.
* zpool_expand_001_pos, zpool_expand_003_neg - Requires
additional support from the ZED, updated skip reason.
* zfs_rollback_001_pos, zfs_rollback_002_pos - Properly cleanup
busy mount points under Linux between test loops.
* privilege_001_pos, privilege_003_pos, rollback_003_pos,
threadsappend_001_pos - Skip with log_unsupported.
* snapshot_016_pos - No changes required.
* snapshot_008_pos - Increased LIMIT from 512K to 2M and added
sync_pool to avoid false positives.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6128
This addition will enable us to sync an open TXG to the main pool
on demand. The functionality is similar to 'sync(2)' but 'zpool sync'
will return when data has hit the main storage instead of potentially
just the ZIL as is the case with the 'sync(2)' cmd.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6122
Enable additional test cases, in most cases this required a few
minor modifications to the test scripts. In a few cases a real
bug was uncovered and fixed. And in a handful of cases where pools
are layered on pools the test case will be skipped until this is
supported. Details below for each test case.
* zpool_add_004_pos - Skip test on Linux until adding zvols to pools
is fully supported and deadlock free.
* zpool_add_005_pos.ksh - Skip dumpadm portion of the test which isn't
relevant for Linux. The find_vfstab_dev, find_mnttab_dev, and
save_dump_dev functions were updated accordingly for Linux. Add
O_EXCL to the in-use check to prevent the -f (force) option from
working for mounted filesystems and improve the resulting error.
* zpool_add_006_pos - Update test case such that it doesn't depend
on nested pools. Switch to truncate from mkfile to reduce space
requirements and speed up the test case.
* zpool_clear_001_pos - Speed up test case by filling filesystem to
25% capacity.
* zpool_create_002_pos, zpool_create_004_pos - Use sparse files for
file vdevs in order to avoid increasing the partition size.
* zpool_create_006_pos - 6ba1ce9 allows raidz+mirror configs with
similar redundancy. Updating the valid_args and forced_args cases.
* zpool_create_008_pos - Disable overlapping partition portion.
* zpool_create_011_neg - Fix to correctly create the extra partition.
Modified zpool_vdev.c to use fstat64_blk() wrapper which includes
the st_size even for block devices.
* zpool_create_012_neg - Updated to properly find swap devices.
* zpool_create_014_neg, zpool_create_015_neg - Updated to use
swap_setup() and swap_cleanup() wrappers which do the right thing
on Linux and Illumos. Removed '-n' option which succeeds under
Linux due to differences in the in-use checks.
* zpool_create_016_pos.ksh - Skipped test case isn't useful.
* zpool_create_020_pos - Added missing / to cleanup() function.
Remove cache file prior to test to ensure a clean environment
and avoid false positives.
* zpool_destroy_001_pos - Removed test case which creates a pool on
a zvol. This is more likely to deadlock under Linux and has never
been completely supported on any platform.
* zpool_destroy_002_pos - 'zpool destroy -f' is unsupported on Linux.
Mount point must not be busy in order to unmount them.
* zfs_destroy_001_pos - Handle EBUSY error which can occur with
volumes when racing with udev.
* zpool_expand_001_pos, zpool_expand_003_neg - Skip test on Linux
until adding zvols to pools is fully supported and deadlock free.
The test could be modified to use loop-back devices but it would
be preferable to use the test case as is for improved coverage.
* zpool_export_004_pos - Updated test case to such that it doesn't
depend on nested pools. Normal file vdev under /var/tmp are fine.
* zpool_import_all_001_pos - Updated to skip partition 1, which is
known as slice 2, on Illumos. This prevents overwriting the
default TESTPOOL which was causing the failure.
* zpool_import_002_pos, zpool_import_012_pos - No changes needed.
* zpool_remove_003_pos - No changes needed
* zpool_upgrade_002_pos, zpool_upgrade_004_pos - Root cause addressed
by upstream OpenZFS commit 3b7f360.
* zpool_upgrade_007_pos - Disabled in test case due to known failure.
Opened issue https://github.com/zfsonlinux/zfs/issues/6112
* zvol_misc_002_pos - Updated to to use ext2.
* zvol_misc_001_neg, zvol_misc_003_neg, zvol_misc_004_pos,
zvol_misc_005_neg, zvol_misc_006_pos - Moved to skip list, these
test case could be updated to use Linux's crash dump facility.
* zvol_swap_* - Updated to use swap_setup/swap_cleanup helpers.
File creation switched from /tmp to /var/tmp. Enabled minimal
useful tests for Linux, skip test cases which aren't applicable.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #3484
Issue #5634
Issue #2437
Issue #5202
Issue #4034Closes#6095
This commit allow higher ashift values (up to 16) in 'zpool create'
The ashift value was previously limited to 13 (8K block) in b41c990
because the limited number of uberblocks we could fit in the
statically sized (128K) vdev label ring buffer could prevent the
ability the safely roll back a pool to recover it.
Since b02fe35 the largest uberblock size we support is 8K: this
allow us to store a minimum number of 16 uberblocks in the vdev
label, even with higher ashift values.
Additionally change 'ashift' pool property behaviour: if set it will
be used as the default hint value in subsequent vdev operations
('zpool add', 'attach' and 'replace'). A custom ashift value can still
be specified from the command line, if desired.
Finally, fix a bug in add-o_ashift.ksh caused by a missing variable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2024Closes#4205Closes#4740Closes#5763
OpenZFS 7252 - compressed zfs send / receive
OpenZFS 7628 - create long versions of ZFS send / receive options
Authored by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: David Quigley <dpquigl@davequigley.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: David Quigley <dpquigl@davequigley.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Ported-by: bunder2015 <omfgbunder@gmail.com>
Ported-by: Don Brady <don.brady@intel.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Most of 7252 was already picked up during ABD work. This
commit represents the gap from the final commit to openzfs.
- Fixed split_large_blocks check in do_dump()
- An alternate version of the write_compressible() function was
implemented for Linux which does not depend on fio. The behavior
of fio differs significantly based on the exact version.
- mkholes was replaced with truncate for Linux.
OpenZFS-issue: https://www.illumos.org/issues/7252
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/5602294Closes#6067
Authored by: Toomas Soome <tsoome@me.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: Marcel Telka <marcel@telka.sk>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Removed gzip and zle compression restriction on bootfs
datasets. Grub added support for these long ago. Ay
version of grub which understands lz4 also supports this.
- Enabled rootpool tests in runfile but skipped by default
in setup on Linux since they modify the rootpool.
- bootfs_006_pos.ksh, striped pools are allowed as bootfs.
OpenZFS-issue: https://www.illumos.org/issues/7404
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/55a424cCloses#5982
Authored by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Multiple changes in this commit were applied in c1d9abf.
OpenZFS-issue: https://www.illumos.org/issues/7629
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f5fb56dCloses#5980
Authored by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Gordon Ross <gordon.w.ross@gmail.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
Porting Notes:
- Utilities which aren't available under Linux have been removed.
- Because of sudo's default secure path behavior PATH must be
explicitly reset at the top of libtest.shlib. This avoids the
need for all users to customize secure path on their system.
- Updated ZoL infrastructure to manage constrained path
- Updated all test cases
- Check permissions for usergroup tests
- When testing in-tree create links under bin/
- Update fault cleanup such that missing files during
cleanup aren't fatal.
- Configure su environment with constrained path
OpenZFS-issue: https://www.illumos.org/issues/7290
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/1d32ba6Closes#5903
Also included are updates to auto-online test
Automated auto-replace test to go along with ZED FMA integration
(PR 4673) auto-replace_001.pos works using a scsi_debug device
(the only usable virtual device currently due to whole_disk var
needing to be set)
Functionality for automated FMA auto-replace test to work with
scsi_debug devs: Some functionality/exceptions needed to be
added for automation of auto-replace to work correctly.
In the test an alias vdev_id rule is added for any scsi_debug
device which sets the phys_path="scsidebug" after a udevadm
trigger command.
A symlink is created for the vdev_id.conf file (in /etc/zfs/ by
default) to be used in-tree for the test suite
(/var/tmp/zfs/vdev_id.conf). "./scripts/zfs-helpers.sh -i" needs
to be run before fault tests in the ZTS (to use udev rules in-tree)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: David Quigley <david.quigley@intel.com>
Signed-off-by: Sydney Vanda <sydney.m.vanda@intel.com>
Closes#5944
Automated auto-online test to go along with ZED FMA integration (PR 4673)
auto_online_001.pos works with real devices (sd- and mpath) and with non-real
block devices (loop) by adding a scsi_debug device to the pool
Note: In order for test group to run, ZED must not currently be running.
Kernel 3.16.37 or higher needed for scsi_debug to work properly
If timeout occurs on test using a scsi_debug device (error noticed on Ubuntu
system), a reboot might be needed in order for test to pass. (more
investigation into this)
Also suppressed output from is_real_device/is_loop_device/is_mpath_device -
was making the log file very cluttered with useless error messages
"ie /dev/mapper/sdc is not a block device" from previous patch
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: David Quigley <david.quigley@intel.com>
Signed-off-by: Sydney Vanda <sydney.m.vanda@intel.com>
Closes#5774
Use -pH flags in get_pool_prop so that numeric properties such as size
can be compared. The zpool_expand test suite is currently the only one
which uses get_pool_prop for a numeric property.
Add TEMPFILE and TEMPFILE{0,1,2} to default.cfg for tests that must
build pools on top of files, such as this one where expansion is
necessary but the entries in DISKS may not point to entities that can be
expanded.
Base the pool used for testing on file-type VDEVs instead of using zvols
within an underlying pool, to avoid issues that come up when pools are
backed by other pools.
Remove shell variables EX_1GB and EX_2GB used to recognize correct expansion,
and instead calculate the appropriate values based on the variables used to
control file or volume size, org_size and exp_size. This change is also
made in test 001 although that test is not enabled because it depends on
FMA.
Finally, enable zpool_expand_002_pos.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5757
Authored by: Yuri Pankov <yuri.pankov@gmail.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Approved by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/6754
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/01ff411Closes#5787
Porting notes:
- Only the ACL test cases used this function and they have been
dropped from ZoL since Linux used POSIX style ACLs.
- functional/acl/nontrivial/zfs_acl_chmod_aclmode_001_pos.ksh
- functional/acl/nontrivial/zfs_acl_chmod_inherit_003_pos.ksh
- functional/acl/nontrivial/zfs_acl_chmod_rwx_002_pos.ksh
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7104
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4b5c8e9Closes#5679
Sometimes the ZTS checks freed space just after `zfs destroy snapshot` and
gets an unexpected value because of space being freed asynchronously.
For cases like this add a `wait_freeing` function which blocks until the
pools `freeing` property drops to zero.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#5740
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#5669Closes#5743
Running tests locally were failing on cleanup scripts due to having a
pool named "pool". Match on word so the cleanup logic will cleanup
"testpool.*" while ignoring "pool".
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Tim Crawford <tcrawford@datto.com>
Closes#5703
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5547Closes#5543
When running the ZFS Test Suite with a kmemleak enabled kernel
the following test cases run far slower than usual and may hit
their timeout threshold. Skip the following test cases.
Test: cli_root/zfs_get/zfs_get_009_pos (run as root) [55:43]
Test: cli_root/zpool_clear/zpool_clear_001_pos (run as root) [11:32]
Test: cli_root/zpool_create/zpool_create_024_pos (run as root) [11:01]
Test: features/async_destroy/async_destroy_001_pos (run as root) [41:15]
Test: inheritance/inherit_001_pos (run as root) [09:08]
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #5479Closes#5480
Allow `zfs unshare <protocol> -a` command to share or unshare all datasets
of a given protocol, nfs or smb.
Additionally, enable most of ZFS Test Suite zfs_share/zfs_unshare test cases.
To work around some Illumos-specific functionalities ($SHARE/$UNSHARE) some
function wrappers were added around them.
Finally, fix and issue in smb_is_share_active() that would leave SMB shares
exported when invoking 'zfs unshare -a'
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3238Closes#5367
The async_destroy_001_pos test case currently hangs when testing on
a 32-bit system. Conditionally skip this test case on 32-bit
systems until the root cause is identified and resolved.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #5352
Issue #5347
This patch tracks dnode usage for each user/group in the
DMU_USER/GROUPUSED_OBJECT ZAPs. ZAP entries dedicated to dnode
accounting have the key prefixed with "obj-" followed by the UID/GID
in string format (as done for the block accounting).
A new SPA feature has been added for dnode accounting as well as
a new ZPL version. The SPA feature must be enabled in the pool
before upgrading the zfs filesystem. During the zfs version upgrade,
a "quotacheck" will be executed by marking all dnode as dirty.
ZoL-bug-id: https://github.com/zfsonlinux/zfs/issues/3500
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Johann Lombardi <johann.lombardi@intel.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported by: Tony Hutter <hutter2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/4185
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/45818ee
Porting Notes:
This code is ported on top of the Illumos Crypto Framework code:
b5e030c8db
The list of porting changes includes:
- Copied module/icp/include/sha2/sha2.h directly from illumos
- Removed from module/icp/algs/sha2/sha2.c:
#pragma inline(SHA256Init, SHA384Init, SHA512Init)
- Added 'ctx' to lib/libzfs/libzfs_sendrecv.c:zio_checksum_SHA256() since
it now takes in an extra parameter.
- Added CTASSERT() to assert.h from for module/zfs/edonr_zfs.c
- Added skein & edonr to libicp/Makefile.am
- Added sha512.S. It was generated from sha512-x86_64.pl in Illumos.
- Updated ztest.c with new fletcher_4_*() args; used NULL for new CTX argument.
- In icp/algs/edonr/edonr_byteorder.h, Removed the #if defined(__linux) section
to not #include the non-existant endian.h.
- In skein_test.c, renane NULL to 0 in "no test vector" array entries to get
around a compiler warning.
- Fixup test files:
- Rename <sys/varargs.h> -> <varargs.h>, <strings.h> -> <string.h>,
- Remove <note.h> and define NOTE() as NOP.
- Define u_longlong_t
- Rename "#!/usr/bin/ksh" -> "#!/bin/ksh -p"
- Rename NULL to 0 in "no test vector" array entries to get around a
compiler warning.
- Remove "for isa in $($ISAINFO); do" stuff
- Add/update Makefiles
- Add some userspace headers like stdio.h/stdlib.h in places of
sys/types.h.
- EXPORT_SYMBOL *_Init/*_Update/*_Final... routines in ICP modules.
- Update scripts/zfs2zol-patch.sed
- include <sys/sha2.h> in sha2_impl.h
- Add sha2.h to include/sys/Makefile.am
- Add skein and edonr dirs to icp Makefile
- Add new checksums to zpool_get.cfg
- Move checksum switch block from zfs_secpolicy_setprop() to
zfs_check_settable()
- Fix -Wuninitialized error in edonr_byteorder.h on PPC
- Fix stack frame size errors on ARM32
- Don't unroll loops in Skein on 32-bit to save stack space
- Add memory barriers in sha2.c on 32-bit to save stack space
- Add filetest_001_pos.ksh checksum sanity test
- Add option to write psudorandom data in file_write utility
Author: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Don Brady <don.brady@intel.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: David Quigley <david.quigley@intel.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Don Brady <don.brady@intel.com>
OpenZFS-issue: https://www.illumos.org/issues/6950
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/dcbf3bd6
Delphix-commit: https://github.com/delphix/delphix-os/commit/978ed49Closes#4929
ZFS Test Suite Performance Regression Tests
This was pulled into OpenZFS via the compressed arc featureand was
separated out in zfsonlinux as a separate pull request from PR-4768.
It originally came in as QA-4903 in Delphix-OS from John Kennedy.
Expected Usage:
$ DISKS="sdb sdc sdd" zfs-tests.sh -r perf-regression.run
Porting Notes:
1. Added assertions in the setup script to make sure required tools
(fio, mpstat, ...) are present.
2. For the config.json generation in perf.shlib used arcstats and
other binaries instead of dtrace to query the values.
3. For the perf data collection:
- use "zpool iostat -lpvyL" instead of the io.d dtrace script
(currently not collecting zfs_read/write latency stats)
- mpstat and iostat take different arguments
- prefetch_io.sh is a placeholder that uses arcstats instead of
dtrace
4. Build machines require fio, mdadm and sysstat pakage (YMMV).
Future Work:
- Need a way to measure zfs_read and zfs_write latencies per pool.
- Need tools to takes two sets of output and display/graph the
differences
- Bring over additional regression tests from Delphix
When using real devices, specify DISKS="sdb sdc sdd" opposed to
/dev/sdb in zfs-tests.sh - otherwise errors with directory names and
disk names registering as "/dev//dev/sdb" for some tests. The same
goes for mpath: DISK="mpatha mpathad mpathb"
Expected Usage:
$ DISKS="sdb sdc sdd" zfs-tests.sh
SLICE_PREFIX is now set as "p" for a loop device (ie loop0p2) or
"" for a real device (ie sdb2), or either for multipath devices
(ie mpatha1 or mpath1p1) instead of only "p" by default. Note that
kpartx partitioning is not currently supported in this patch
(ie "partx") and may need to be disabled on Debian distributions.
Functions added for determining test directory (/dev or /dev/mapper)
as well as slice prefix are determined and exported mostly in the cfg
file of each test group directory.
Currently zpools cannot be created on whole mpath devices that have
been partitioned. In order to fix this tests have either been revised
to use a partition instead, or if there is a size constraint and the
pool needs to be created on the whole disk, partitions are then deleted
if the device is a multipath device. This functionality is added to
default_cleanup() or to individual cleanup scripts if a non-default
cleanup method is used.
The max partitions is currently set at 8 to account for all of the
tests thus far.
Patch changes are generally encompassed in "if is_linux" construct.
Signed-off-by: Sydney Vanda <sydney.m.vanda@intel.com>
Reviewed-by: John Salinas <John.Salinas@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: David Quigley <david.quigley@intel.com>
Closes#4447Closes#4964Closes#5074
ZFS allows for specific permissions to be delegated to normal users
with the `zfs allow` and `zfs unallow` commands. In addition, non-
privileged users should be able to run all of the following commands:
* zpool [list | iostat | status | get]
* zfs [list | get]
Historically this functionality was not available on Linux. In order
to add it the secpolicy_* functions needed to be implemented and mapped
to the equivalent Linux capability. Only then could the permissions on
the `/dev/zfs` be relaxed and the internal ZFS permission checks used.
Even with this change some limitations remain. Under Linux only the
root user is allowed to modify the namespace (unless it's a private
namespace). This means the mount, mountpoint, canmount, unmount,
and remount delegations cannot be supported with the existing code. It
may be possible to add this functionality in the future.
This functionality was validated with the cli_user and delegation test
cases from the ZFS Test Suite. These tests exhaustively verify each
of the supported permissions which can be delegated and ensures only
an authorized user can perform it.
Two minor bug fixes were required for test-running.py. First, the
Timer() object cannot be safely created in a `try:` block when there
is an unconditional `finally` block which references it. Second,
when running as a normal user also check for scripts using the
both the .ksh and .sh suffixes.
Finally, existing users who are simulating delegations by setting
group permissions on the /dev/zfs device should revert that
customization when updating to a version with this change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#362Closes#434Closes#4100Closes#4394Closes#4410Closes#4487
When ZFS is installed by 'make install', programs will be installed
into '/usr/local'. ZFS test scripts can't locate programs 'zpool'
that caused tests failure.
Fix typo in help message.
Add sanity check to for ksh and generate a useful error message.
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4495
Add the ZFS Test Suite and test-runner framework from illumos.
This is a continuation of the work done by Turbo Fredriksson to
port the ZFS Test Suite to Linux. While this work was originally
conceived as a stand alone project integrating it directly with
the ZoL source tree has several advantages:
* Allows the ZFS Test Suite to be packaged in zfs-test package.
* Facilitates easy integration with the CI testing.
* Users can locally run the ZFS Test Suite to validate ZFS.
This testing should ONLY be done on a dedicated test system
because the ZFS Test Suite in its current form is destructive.
* Allows the ZFS Test Suite to be run directly in the ZoL source
tree enabled developers to iterate quickly during development.
* Developers can easily add/modify tests in the framework as
features are added or functionality is changed. The tests
will then always be in sync with the implementation.
Full documentation for how to run the ZFS Test Suite is available
in the tests/README.md file.
Warning: This test suite is designed to be run on a dedicated test
system. It will make modifications to the system including, but
not limited to, the following.
* Adding new users
* Adding new groups
* Modifying the following /proc files:
* /proc/sys/kernel/core_pattern
* /proc/sys/kernel/core_uses_pid
* Creating directories under /
Notes:
* Not all of the test cases are expected to pass and by default
these test cases are disabled. The failures are primarily due
to assumption made for illumos which are invalid under Linux.
* When updating these test cases it should be done in as generic
a way as possible so the patch can be submitted back upstream.
Most existing library functions have been updated to be Linux
aware, and the following functions and variables have been added.
* Functions:
* is_linux - Used to wrap a Linux specific section.
* block_device_wait - Waits for block devices to be added to /dev/.
* Variables: Linux Illumos
* ZVOL_DEVDIR "/dev/zvol" "/dev/zvol/dsk"
* ZVOL_RDEVDIR "/dev/zvol" "/dev/zvol/rdsk"
* DEV_DSKDIR "/dev" "/dev/dsk"
* DEV_RDSKDIR "/dev" "/dev/rdsk"
* NEWFS_DEFAULT_FS "ext2" "ufs"
* Many of the disabled test cases fail because 'zfs/zpool destroy'
returns EBUSY. This is largely causes by the asynchronous nature
of device handling on Linux and is expected, the impacted test
cases will need to be updated to handle this.
* There are several test cases which have been disabled because
they can trigger a deadlock. A primary example of this is to
recursively create zpools within zpools. These tests have been
disabled until the root issue can be addressed.
* Illumos specific utilities such as (mkfile) should be added to
the tests/zfs-tests/cmd/ directory. Custom programs required by
the test scripts can also be added here.
* SELinux should be either is permissive mode or disabled when
running the tests. The test cases should be updated to conform
to a standard policy.
* Redundant test functionality has been removed (zfault.sh).
* Existing test scripts (zconfig.sh) should be migrated to use
the framework for consistency and ease of testing.
* The DISKS environment variable currently only supports loopback
devices because of how the ZFS Test Suite expects partitions to
be named (p1, p2, etc). Support must be added to generate the
correct partition name based on the device location and name.
* The ZFS Test Suite is part of the illumos code base at:
https://github.com/illumos/illumos-gate/tree/master/usr/src/test
Original-patch-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6Closes#1534
