Coverity complained about the format specifiers not matching variables.
In one case, the variable is a constant, so we fix it. In another, we
were missing an argument (about which coverity also complained).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13888
Users were seeing floods of `config_sync` events when autoexpand was
enabled. This happened because all "disk status change" udev events
invoke the autoexpand codepath, which calls zpool_relabel_disk(),
which in turn cause another "disk status change" event to happen,
in a feedback loop. Note that "disk status change" happens every time
a user calls close() on a block device.
This commit breaks the feedback loop by only allowing an autoexpand
to happen if the disk actually changed size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes: #7132Closes: #7366Closes#13729
We tried replacing an NVMe drive using autoreplace, only
to see zed reject it with:
zed[27955]: zed_udev_monitor: /dev/nvme5n1 no devid source
This happened because ZED saw that ID_BUS was not set by udev
for the NVMe drive, and thus didn't think it was "real drive".
This commit allows NVMe drives to be autoreplaced even if
ID_BUS is not set.
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13512Closes#13646
libudev will sometimes falsely identify an 'atari' partition on a
blank disk, preventing it from being used in an autoreplace. This
seems to be a known issue. The workaround is to just ignore the
fake partition and continue with the autoreplace.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13497Closes#13632
Clang trunk now warns -Wstrict-prototypes on this, and they're removed
in C2x
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13447
We recently had a case where our operators replaced a bad
multipathed disk, only to see it fail to autoreplace. The
zed logs showed that the multipath replacement disk did not pass
the 'is_dm' test in zfs_process_add() even though it should have.
is_dm is set if there exists a sysfs entry for to the
underlying /dev/sd* paths for the multipath disk. It's
possible this path didn't exist due to a race condition where
the sysfs paths weren't created at the time the udev event came
in to zed, but this was never verified.
This patch updates the check to look for udev properties that
indicate if the new autoreplace disk is an empty multipath disk,
rather than looking for the underlying sysfs entries. It also
adds in additional logging, and fixes a bug where zed allowed
you to use an already zfs-formatted disk from another pool
as a multipath auto-replacement disk.
Furthermore, while testing this patch, I also ran across a case
where a force-faulted disk did not have a ZPOOL_CONFIG_PHYS_PATH
entry in its config. This prevented it from being autoreplaced.
I added additional logic to derive the PHYS_PATH from the PATH if
the PATH was a /dev/disk/by-vdev/ path. For example, if PATH
was /dev/disk/by-vdev/L28, then PHYS_PATH would be L28. This is
safe since by-vdev paths represent physical locations and do not
change between boots.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13023
This enables ZED to auto-online vdevs that are not wholedisk managed by
ZFS.
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Adds a libzutil for utility functions that are common to libzfs and
libzpool consumers (most of what was in libzfs_import.c). This
removes the need for utilities to link against both libzpool and
libzfs.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#8050
Enable most of the remaining test cases which were previously
disabled. The required fixes are as follows:
* cache_001_pos - No changes required.
* cache_010_neg - Updated to use losetup under Linux. Loopback
cache devices are allowed, ZVOLs as cache devices are not.
Disabled until all the builders pass reliably.
* cachefile_001_pos, cachefile_002_pos, cachefile_003_pos,
cachefile_004_pos - Set set_device_dir path in cachefile.cfg,
updated CPATH1 and CPATH2 to reference unique files.
* zfs_clone_005_pos - Wait for udev to create volumes.
* zfs_mount_007_pos - Updated mount options to expected Linux names.
* zfs_mount_009_neg, zfs_mount_all_001_pos - No changes required.
* zfs_unmount_005_pos, zfs_unmount_009_pos, zfs_unmount_all_001_pos -
Updated to expect -f to not unmount busy mount points under Linux.
* rsend_019_pos - Observed to occasionally take a long time on both
32-bit systems and the kmemleak builder.
* zfs_written_property_001_pos - Switched sync(1) to sync_pool.
* devices_001_pos, devices_002_neg - Updated create_dev_file() helper
for Linux.
* exec_002_neg.ksh - Fixed mmap_exec.c to preserve errno. Updated
test case to expect EPERM from Linux as described by mmap(2).
* grow_pool_001_pos - Adding missing setup.ksh and cleanup.ksh
scripts from OpenZFS.
* grow_replicas_001_pos.ksh - Added missing $SLICE_* variables.
* history_004_pos, history_006_neg, history_008_pos - Fixed by
previous commits and were not enabled. No changes required.
* zfs_allow_010_pos - Added missing spaces after assorted zfs
commands in delegate_common.kshlib.
* inuse_* - Illumos dump device tests skipped. Remaining test
cases updated to correctly create required partitions.
* large_files_001_pos - Fixed largest_file.c to accept EINVAL
as well as EFBIG as described in write(2).
* link_count_001 - Added nproc to required commands.
* umountall_001 - Updated to use umount -a.
* online_offline_001_* - Pull in OpenZFS change to file_trunc.c
to make the '-c 0' option run the test in a loop. Included
online_offline.cfg file in all test cases.
* rename_dirs_001_pos - Updated to use the rename_dir test binary,
pkill restricted to exact matches and total runtime reduced.
* slog_013_neg, write_dirs_002_pos - No changes required.
* slog_013_pos.ksh - Updated to use losetup under Linux.
* slog_014_pos.ksh - ZED will not be running, manually degrade
the damaged vdev as expected.
* nopwrite_varying_compression, nopwrite_volume - Forced pool
sync with sync_pool to ensure up to date property values.
* Fixed typos in ZED log messages. Refactored zed_* helper
functions to resolve all-syslog exit=1 errors in zedlog.
* zfs_copies_005_neg, zfs_get_004_pos, zpool_add_004_pos,
zpool_destroy_001_pos, largest_pool_001_pos, clone_001_pos.ksh,
clone_001_pos, - Skip until layering pools on zvols is solid.
* largest_pool_001_pos - Limited to 7eb pool, maximum
supported size in 8eb-1 on Linux.
* zpool_expand_001_pos, zpool_expand_003_neg - Requires
additional support from the ZED, updated skip reason.
* zfs_rollback_001_pos, zfs_rollback_002_pos - Properly cleanup
busy mount points under Linux between test loops.
* privilege_001_pos, privilege_003_pos, rollback_003_pos,
threadsappend_001_pos - Skip with log_unsupported.
* snapshot_016_pos - No changes required.
* snapshot_008_pos - Increased LIMIT from 512K to 2M and added
sync_pool to avoid false positives.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6128
Also included are updates to auto-online test
Automated auto-replace test to go along with ZED FMA integration
(PR 4673) auto-replace_001.pos works using a scsi_debug device
(the only usable virtual device currently due to whole_disk var
needing to be set)
Functionality for automated FMA auto-replace test to work with
scsi_debug devs: Some functionality/exceptions needed to be
added for automation of auto-replace to work correctly.
In the test an alias vdev_id rule is added for any scsi_debug
device which sets the phys_path="scsidebug" after a udevadm
trigger command.
A symlink is created for the vdev_id.conf file (in /etc/zfs/ by
default) to be used in-tree for the test suite
(/var/tmp/zfs/vdev_id.conf). "./scripts/zfs-helpers.sh -i" needs
to be run before fault tests in the ZTS (to use udev rules in-tree)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: David Quigley <david.quigley@intel.com>
Signed-off-by: Sydney Vanda <sydney.m.vanda@intel.com>
Closes#5944
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5547Closes#5543
Enable picky cstyle checks and resolve the new warnings. The vast
majority of the changes needed were to handle minor issues with
whitespace formatting. This patch contains no functional changes.
Non-whitespace changes are as follows:
* 8 times ; to { } in for/while loop
* fix missing ; in cmd/zed/agents/zfs_diagnosis.c
* comment (confim -> confirm)
* change endline , to ; in cmd/zpool/zpool_main.c
* a number of /* BEGIN CSTYLED */ /* END CSTYLED */ blocks
* /* CSTYLED */ markers
* change == 0 to !
* ulong to unsigned long in module/zfs/dsl_scan.c
* rearrangement of module_param lines in module/zfs/metaslab.c
* add { } block around statement after for_each_online_node
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5465
The phase 2 work primarily entails the Diagnosis Engine and
the Retire Agent modules. It also includes infrastructure
to support a crude FMD environment to host these modules.
The Diagnosis Engine consumes I/O and checksum ereports and
feeds them into a SERD engine which will generate a corres-
ponding fault diagnosis when the SERD engine fires. All the
diagnosis state data is collected into cases, one case per
vdev being tracked.
The Retire Agent responds to diagnosed faults by isolating
the faulty VDEV. It will notify the ZFS kernel module of
the new VDEV state (degraded or faulted). This agent is
also responsible for managing hot spares across pools.
When it encounters a device fault or a device removal it
replaces the device with an appropriate spare if available.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#5343
Previously when a drive faulted, the statechange-led.sh script would lookup
the drive's LED sysfs entry in /sys/block/sd*/device/enclosure_device, and
turn it on. During testing we noticed that if you pulled out a drive, or if
the drive was so badly broken that it no longer appeared to Linux, that the
/sys/block/sd* path would be removed, and the script could not lookup the
LED entry.
To fix this, this patch looks up the disks's more persistent
"/sys/class/enclosure/X:X:X:X/Slot N" LED sysfs path at pool import. It then
passes that path to the statechange-led script to use, rather than having the
script look it up on the fly. This allows the script to turn on/off the slot
LEDs even when the drive is missing.
Closes#5309Closes#2375
1. Enable multipath autoreplace support for FMA.
This extends FMA autoreplace to work with multipath disks. This
requires libdevmapper to be installed at build time.
2. Turn on/off fault LEDs when VDEVs become degraded/faulted/online
Set ZED_USE_ENCLOSURE_LEDS=1 in zed.rc to have ZED turn on/off the enclosure
LED for a drive when a drive becomes FAULTED/DEGRADED. Your enclosure must
be supported by the Linux SES driver for this to work. The enclosure LED
scripts work for multipath devices as well. The scripts will clear the LED
when the fault is cleared.
3. Rate limit ZIO delay and checksum events so as not to flood ZED
ZIO delay and checksum events are rate limited to 5/sec in the zfs module.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#2449Closes#3017Closes#5159
This first phase brings over the ZFS SLM module, zfs_mod.c, to handle
auto operations in response to disk events. Disk event monitoring is
provided from libudev and generates the expected payload schema for
zfs_mod. This work leverages the recently added devid and phys_path
strings in the vdev label.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#4673
