mirror of
https://git.proxmox.com/git/mirror_zfs.git
synced 2024-11-17 10:01:01 +03:00
4694131a0a
6 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Matthew Ahrens
|
069bf406b4
|
vdev_draid_min_asize() ignores reserved space
vdev_draid_min_asize() returns the minimum size of a child vdev. This is used when determining if a disk is big enough to replace a child. It's also used by zdb to determine how big of a child to make to test replacement. vdev_draid_min_asize() says that the child’s asize has to be at least 1/Nth of the entire draid’s asize, which is the same logic as raidz. However, this contradicts the code in vdev_draid_open(), which calculates the draid’s asize based on a reduced child size: An additional 32MB of scratch space is reserved at the end of each child for use by the dRAID expansion feature So the problem is that you can replace a draid disk with one that’s vdev_draid_min_asize(), but it actually needs to be larger to accommodate the additional 32MB. The replacement is allowed and everything works at first (since the reserved space is at the end, and we don’t try to use it yet), but when you try to close and reopen the pool, vdev_draid_open() calculates a smaller asize for the draid, because of the smaller leaf, which is not allowed. I think the confusion is that vdev_draid_min_asize() is correctly returning the amount of required *allocatable* space in a leaf, but the actual *size* of the leaf needs to be at least 32MB more than that. ztest_vdev_attach_detach() assumes that it can attach that size of device, and it actually can (the kernel/libzpool accepts it), but it then later causes zdb to not be able to open the pool. This commit changes vdev_draid_min_asize() to return the required size of the leaf, not the size that draid will make available to the metaslab allocator. Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: Mark Maybee <mark.maybee@delphix.com> Signed-off-by: Matthew Ahrens <mahrens@delphix.com> Closes #11459 Closes #12221 |
||
|
Brian Behlendorf
|
8fb577ae6d
|
Fix dRAID sequential resilver silent damage handling
This change addresses two distinct scenarios which are possible when performing a sequential resilver to a dRAID pool with vdevs that contain silent unknown damage. Which in this circumstance took the form of the devices being intentionally overwritten with zeros. However, it could also result from a device returning incorrect data while a sequential resilver was in progress. Scenario 1) A sequential resilver is performed while all of the dRAID vdevs are ONLINE and there is silent damage present on the vdev being resilvered. In this case, nothing will be repaired by vdev_raidz_io_done_reconstruct_known_missing() because rc->rc_error isn't set on any of the raid columns. To address this vdev_draid_io_start_read() has been updated to always mark the resilvering column as ESTALE for sequential resilver IO. Scenario 2) Multiple columns contain silent damage for the same block and a sequential resilver is performed. In this case it's impossible to generate the correct data from parity unless all of the damaged columns are being sequentially resilvered (and thus only good data is used to generate parity). This is as expected and there's nothing which can be done about it. However, we need to be careful not to make to situation worse. Since we can't verify the data is actually good without a checksum, we must only repair the devices which are being sequentially resilvered. Otherwise, an incorrect repair to a device which previously contained good data could effectively lock in the damage and make reconstruction impossible. A check for this was added to vdev_raidz_io_done_verified() along with a new test case. Lastly, this change updates the redundancy_draid_spare1 and redundancy_draid_spare3 test cases to be more representative of normal dRAID replacement operation. Specifically, what we care about is that the scrub run after a sequential resilver does not find additional blocks which need repair. This would indicate the sequential resilver failed to rebuild a section of one of the devices. Note also the tests were switched to using the verify_pool() function which still checks for checksum errors. Reviewed-by: Mark Maybee <mark.maybee@delphix.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Closes #12061 |
||
|
Brian Behlendorf
|
93c8e91fe7
|
Fix dRAID self-healing short columns
When dRAID performs a normal read operation only the data columns in the raid map are read from disk. This is enough information to calculate the checksum, verify it, and return the needed data to the application. It's only in the event of a checksum failure that the additional parity and any empty columns must be read since they are required for parity reconstruction. Reading these additional columns is handled by vdev_raidz_read_all() which calls vdev_draid_map_alloc_empty() to expand the raid_map_t and submit IOs for the missing columns. This all works correctly, but it fails to account for any "short" columns. These are data columns which are padded with a empty skip sector at the end. Since that empty sector is not needed for a normal read it's not read when columns is first read from disk. However, like the parity and empty columns the skip sector is needed to perform reconstruction. The fix is to mark any "short" columns as never being read by clearing the rc_tried flag when expanding the raid_map_t. This will cause the entire column to re-read from disk in the event of a checksum failure allowing the self-healing functionality to repair the block. Note that this only effects the self-healing feature because when scrubbing a pool the parity, data, and empty columns are all read initially to verify their contents. Furthermore, only blocks which contain "short" columns would be effected, and only when the memory backing the skip sector wasn't already zeroed out. This change extends the existing redundancy_raidz.ksh test case to verify self-healing (as well as resilver and scrub). Then applies the same test case to dRAID with a slightly modified version of the test script called redundancy_draid.ksh. The unused variable combrec was also removed from both test cases. Reviewed-by: Matthew Ahrens <mahrens@delphix.com> Reviewed-by: Mark Maybee <mark.maybee@delphix.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Closes #12010 |
||
|
Matthew Ahrens
|
330c6c0523
|
Clean up RAIDZ/DRAID ereport code
The RAIDZ and DRAID code is responsible for reporting checksum errors on their child vdevs. Checksum errors represent events where a disk returned data or parity that should have been correct, but was not. In other words, these are instances of silent data corruption. The checksum errors show up in the vdev stats (and thus `zpool status`'s CKSUM column), and in the event log (`zpool events`). Note, this is in contrast with the more common "noisy" errors where a disk goes offline, in which case ZFS knows that the disk is bad and doesn't try to read it, or the device returns an error on the requested read or write operation. RAIDZ/DRAID generate checksum errors via three code paths: 1. When RAIDZ/DRAID reconstructs a damaged block, checksum errors are reported on any children whose data was not used during the reconstruction. This is handled in `raidz_reconstruct()`. This is the most common type of RAIDZ/DRAID checksum error. 2. When RAIDZ/DRAID is not able to reconstruct a damaged block, that means that the data has been lost. The zio fails and an error is returned to the consumer (e.g. the read(2) system call). This would happen if, for example, three different disks in a RAIDZ2 group are silently damaged. Since the damage is silent, it isn't possible to know which three disks are damaged, so a checksum error is reported against every child that returned data or parity for this read. (For DRAID, typically only one "group" of children is involved in each io.) This case is handled in `vdev_raidz_cksum_finish()`. This is the next most common type of RAIDZ/DRAID checksum error. 3. If RAIDZ/DRAID is not able to reconstruct a damaged block (like in case 2), but there happens to be additional copies of this block due to "ditto blocks" (i.e. multiple DVA's in this blkptr_t), and one of those copies is good, then RAIDZ/DRAID compares each sector of the data or parity that it retrieved with the good data from the other DVA, and if they differ then it reports a checksum error on this child. This differs from case 2 in that the checksum error is reported on only the subset of children that actually have bad data or parity. This case happens very rarely, since normally only metadata has ditto blocks. If the silent damage is extensive, there will be many instances of case 2, and the pool will likely be unrecoverable. The code for handling case 3 is considerably more complicated than the other cases, for two reasons: 1. It needs to run after the main raidz read logic has completed. The data RAIDZ read needs to be preserved until after the alternate DVA has been read, which necessitates refcounts and callbacks managed by the non-raidz-specific zio layer. 2. It's nontrivial to map the sections of data read by RAIDZ to the correct data. For example, the correct data does not include the parity information, so the parity must be recalculated based on the correct data, and then compared to the parity that was read from the RAIDZ children. Due to the complexity of case 3, the rareness of hitting it, and the minimal benefit it provides above case 2, this commit removes the code for case 3. These types of errors will now be handled the same as case 2, i.e. the checksum error will be reported against all children that returned data or parity. Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Matthew Ahrens <mahrens@delphix.com> Closes #11735 |
||
|
Matthew Ahrens
|
e2af2acce3
|
allow callers to allocate and provide the abd_t struct
The `abd_get_offset_*()` routines create an abd_t that references another abd_t, and doesn't allocate any pages/buffers of its own. In some workloads, these routines may be called frequently, to create many abd_t's representing small pieces of a single large abd_t. In particular, the upcoming RAIDZ Expansion project makes heavy use of these routines. This commit adds the ability for the caller to allocate and provide the abd_t struct to a variant of `abd_get_offset_*()`. This eliminates the cost of allocating the abd_t and performing the accounting associated with it (`abdstat_struct_size`). The RAIDZ/DRAID code uses this for the `rc_abd`, which references the zio's abd. The upcoming RAIDZ Expansion project will leverage this infrastructure to increase performance of reads post-expansion by around 50%. Additionally, some of the interfaces around creating and destroying abd_t's are cleaned up. Most significantly, the distinction between `abd_put()` and `abd_free()` is eliminated; all types of abd_t's are now disposed of with `abd_free()`. Reviewed-by: Brian Atkinson <batkinson@lanl.gov> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Matthew Ahrens <mahrens@delphix.com> Issue #8853 Closes #11439 |
||
|
Brian Behlendorf
|
b2255edcc0
|
Distributed Spare (dRAID) Feature
This patch adds a new top-level vdev type called dRAID, which stands
for Distributed parity RAID. This pool configuration allows all dRAID
vdevs to participate when rebuilding to a distributed hot spare device.
This can substantially reduce the total time required to restore full
parity to pool with a failed device.
A dRAID pool can be created using the new top-level `draid` type.
Like `raidz`, the desired redundancy is specified after the type:
`draid[1,2,3]`. No additional information is required to create the
pool and reasonable default values will be chosen based on the number
of child vdevs in the dRAID vdev.
zpool create <pool> draid[1,2,3] <vdevs...>
Unlike raidz, additional optional dRAID configuration values can be
provided as part of the draid type as colon separated values. This
allows administrators to fully specify a layout for either performance
or capacity reasons. The supported options include:
zpool create <pool> \
draid[<parity>][:<data>d][:<children>c][:<spares>s] \
<vdevs...>
- draid[parity] - Parity level (default 1)
- draid[:<data>d] - Data devices per group (default 8)
- draid[:<children>c] - Expected number of child vdevs
- draid[:<spares>s] - Distributed hot spares (default 0)
Abbreviated example `zpool status` output for a 68 disk dRAID pool
with two distributed spares using special allocation classes.
```
pool: tank
state: ONLINE
config:
NAME STATE READ WRITE CKSUM
slag7 ONLINE 0 0 0
draid2:8d:68c:2s-0 ONLINE 0 0 0
L0 ONLINE 0 0 0
L1 ONLINE 0 0 0
...
U25 ONLINE 0 0 0
U26 ONLINE 0 0 0
spare-53 ONLINE 0 0 0
U27 ONLINE 0 0 0
draid2-0-0 ONLINE 0 0 0
U28 ONLINE 0 0 0
U29 ONLINE 0 0 0
...
U42 ONLINE 0 0 0
U43 ONLINE 0 0 0
special
mirror-1 ONLINE 0 0 0
L5 ONLINE 0 0 0
U5 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
L6 ONLINE 0 0 0
U6 ONLINE 0 0 0
spares
draid2-0-0 INUSE currently in use
draid2-0-1 AVAIL
```
When adding test coverage for the new dRAID vdev type the following
options were added to the ztest command. These options are leverages
by zloop.sh to test a wide range of dRAID configurations.
-K draid|raidz|random - kind of RAID to test
-D <value> - dRAID data drives per group
-S <value> - dRAID distributed hot spares
-R <value> - RAID parity (raidz or dRAID)
The zpool_create, zpool_import, redundancy, replacement and fault
test groups have all been updated provide test coverage for the
dRAID feature.
Co-authored-by: Isaac Huang <he.huang@intel.com>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Co-authored-by: Don Brady <don.brady@delphix.com>
Co-authored-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mmaybee@cray.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #10102
|