Mirrors are supposed to provide redundancy in the face of whole-disk
failure and silent damage (e.g. some data on disk is not right, but ZFS
hasn't detected the whole device as being broken). However, the current
device removal implementation bypasses some of the mirror's redundancy.
Note that in no case is incorrect data returned, but we might get a
checksum error when we should have been able to find the right data.
There are two underlying problems:
1. When we remove a mirror device, we only read one side of the mirror.
Since we can't verify the checksum, this side may be silently bad, but
the good data is on the other side of the mirror (which we didn't read).
This can cause the removal to "bake in" the busted data – all copies of
the data in the new location are the same, busted version, while we left
the good version behind.
The fix for this is to read and copy both sides of the mirror. If the
old and new vdevs are mirrors, we will read both sides of the old
mirror, and write each copy to the corresponding side of the new mirror.
(If the old and new vdevs have a different number of children, we will
do this as best as possible.) Even though we aren't verifying checksums,
this ensures that as long as there's a good copy of the data, we'll have
a good copy after the removal, even if there's silent damage to one side
of the mirror. If we're removing a mirror that has some silent damage,
we'll have exactly the same damage in the new location (assuming that
the new location is also a mirror).
2. When we read from an indirect vdev that points to a mirror vdev, we
only consider one copy of the data. This can lead to reduced effective
redundancy, because we might read a bad copy of the data from one side
of the mirror, and not retry the other, good side of the mirror.
Note that the problem is not with the removal process, but rather after
the removal has completed (having copied correct data to both sides of
the mirror), if one side of the new mirror is silently damaged, we
encounter the problem when reading the relocated data via the indirect
vdev. Also note that the problem doesn't occur when ZFS knows that one
side of the mirror is bad, e.g. when a disk entirely fails or is
offlined.
The impact is that reads (from indirect vdevs that point to mirrors) may
return a checksum error even though the good data exists on one side of
the mirror, and scrub doesn't repair all data on the mirror (if some of
it is pointed to via an indirect vdev).
The fix for this is complicated by "split blocks" - one logical block
may be split into two (or more) pieces with each piece moved to a
different new location. In this case we need to read all versions of
each split (one from each side of the mirror), and figure out which
combination of versions results in the correct checksum, and then repair
the incorrect versions.
This ensures that we supply the same redundancy whether you use device
removal or not. For example, if a mirror has small silent errors on all
of its children, we can still reconstruct the correct data, as long as
those errors are at sufficiently-separated offsets (specifically,
separated by the largest block size - default of 128KB, but up to 16MB).
Porting notes:
* A new indirect vdev check was moved from dsl_scan_needs_resilver_cb()
to dsl_scan_needs_resilver(), which was added to ZoL as part of the
sequential scrub work.
* Passed NULL for zfs_ereport_post_checksum()'s zbookmark_phys_t
parameter. The extra parameter is unique to ZoL.
* When posting indirect checksum errors the ABD can be passed directly,
zfs_ereport_post_checksum() is not yet ABD-aware in OpenZFS.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9290
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/591Closes#6900
OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1ebCloses#6900
This change adds five new tests to the ZTS:
* zpool_split_cliargs: verify command line options and arguments
* zpool_split_devices: verify zpool split accepts a device list
* zpool_split_encryption: verify zpool can split encrypted pools
* zpool_split_props: verify zpool split can set property values
* zpool_split_vdevs: verify vdev layout when splitting the pool
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7409
Commit e4010f2 accidentally allows zpool to set pool features to
"disabled"; this should only be allowed at pool creation. This commit
adds additional checks and test coverage to 'zpool set'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7402
When given an empty string as a rootds value, bootcfg -C fails with
the error message 'could not set nextboot: '' is an invalid name'.
This should be allowed because it represents clearing the nextboot
configuration.
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9193
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/504645d227Closes#7230
get_format_prompt_string() and zpool_state_to_name() return
a string literal which is read-only, thus they should return
`const char*`.
zpool_get_prop_string() returns a non-const string after
successful nv-lookup, and returns a string literal otherwise.
Since this function is designed to be used for read-only purpose,
the return type should also be `const char*`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#7285
usr/src/uts/common/sys/fs/zfs.h
Change ZPROP_INVAL and ZPROP_CONT from macros to enum values. Clang
and GCC both prefer to use unsigned ints to store enums. That was
causing tautological comparison warnings (and likely eliminating
error handling code at compile time) whenever a zfs_prop_t or
zpool_prop_t was compared to ZPROP_INVAL or ZPROP_CONT. Making the
error flags be explicity enum values forces the enum types to be
signed.
ZPROP_INVAL was also compared against two different enum types. I
had to change its name to ZPOOL_PROP_INVAL whenever its compared to
a zpool_prop_t. There are still some places where ZPROP_INVAL or
ZPROP_CONT is compared to a plain int, in code that doesn't know
whether the int is storing a zfs_prop_t or a zpool_prop_t.
usr/src/uts/common/fs/zfs/spa.c
s/ZPROP_INVAL/ZPOOL_PROP_INVAL/
Authored by: Alan Somers <asomers@gmail.com>
Approved by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8652
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c2de80dc74Closes#7061
Add "spare" and "replacing" to the list of interior vdev types in
zpool_vdev_is_interior(), alongside the existing "mirror" and "raidz".
This fixes running "zinject -d" and "zpool clear" on spare and replacing
vdevs.
Authored by: Alan Somers <asomers@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Melikov <mail@gmelikov.ru>
Approved by: Gordon Ross <gwr@nexenta.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8641
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/9a36801382Closes#7060
Added -n flag to zpool reopen that allows a running scrub
operation to continue if there is a device with Dirty Time Log.
By default if a component device has a DTL and zpool reopen
is executed all running scan operations will be restarted.
Added functional tests for `zpool reopen`
Tests covers following scenarios:
* `zpool reopen` without arguments,
* `zpool reopen` with pool name as argument,
* `zpool reopen` while scrubbing,
* `zpool reopen -n` while scrubbing,
* `zpool reopen -n` while resilvering,
* `zpool reopen` with bad arguments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Closes#6076Closes#6746
This change incorporates three major pieces:
The first change is a keystore that manages wrapping
and encryption keys for encrypted datasets. These
commands mostly involve manipulating the new
DSL Crypto Key ZAP Objects that live in the MOS. Each
encrypted dataset has its own DSL Crypto Key that is
protected with a user's key. This level of indirection
allows users to change their keys without re-encrypting
their entire datasets. The change implements the new
subcommands "zfs load-key", "zfs unload-key" and
"zfs change-key" which allow the user to manage their
encryption keys and settings. In addition, several new
flags and properties have been added to allow dataset
creation and to make mounting and unmounting more
convenient.
The second piece of this patch provides the ability to
encrypt, decyrpt, and authenticate protected datasets.
Each object set maintains a Merkel tree of Message
Authentication Codes that protect the lower layers,
similarly to how checksums are maintained. This part
impacts the zio layer, which handles the actual
encryption and generation of MACs, as well as the ARC
and DMU, which need to be able to handle encrypted
buffers and protected data.
The last addition is the ability to do raw, encrypted
sends and receives. The idea here is to send raw
encrypted and compressed data and receive it exactly
as is on a backup system. This means that the dataset
on the receiving system is protected using the same
user key that is in use on the sending side. By doing
so, datasets can be efficiently backed up to an
untrusted system without fear of data being
compromised.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#494Closes#5769
OpenZFS provides a library called tpool which implements thread
pools for user space applications. Porting this library means
the zpool utility no longer needs to borrow the kernel mutex and
taskq interfaces from libzpool. This code was updated to use
the tpool library which behaves in a very similar fashion.
Porting libtpool was relatively straight forward and minimal
modifications were needed. The core changes were:
* Fully convert the library to use pthreads.
* Updated signal handling.
* lmalloc/lfree converted to calloc/free
* Implemented portable pthread_attr_clone() function.
Finally, update the build system such that libzpool.so is no
longer linked in to zfs(8), zpool(8), etc. All that is required
is libzfs to which the zcommon soures were added (which is the way
it always should have been). Removing the libzpool dependency
resulted in several build issues which needed to be resolved.
* Moved zfeature support to module/zcommon/zfeature_common.c
* Moved ratelimiting to to module/zfs/zfs_ratelimit.c
* Moved get_system_hostid() to lib/libspl/gethostid.c
* Removed use of cmn_err() in zcommon source
* Removed dprintf_setup() call from zpool_main.c and zfs_main.c
* Removed highbit() and lowbit()
* Removed unnecessary library dependencies from Makefiles
* Removed fletcher-4 kstat in user space
* Added sha2 support explicitly to libzfs
* Added highbit64() and lowbit64() to zpool_util.c
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6442
Turning the multihost property on requires that a hostid be set to allow
ZFS to determine when a foreign system is attemping to import a pool.
The error message instructing the user to set a hostid refers to
genhostid(1).
Genhostid(1) is not available on SUSE Linux. This commit adds a script
modeled after genhostid(1) for those users.
Zgenhostid checks for an /etc/hostid file; if it does not exist, it
creates one and stores a value. If the user has provided a hostid as an
argument, that value is used. Otherwise, a random hostid is generated
and stored.
This differs from the CENTOS 6/7 versions of genhostid, which overwrite
the /etc/hostid file even though their manpages state otherwise.
A man page for zgenhostid is added. The one for genhostid is in (1), but
I put zgenhostid in (8) because I believe it's more appropriate.
The mmp tests are modified to use zgenhostid to set the hostid instead
of using the spl_hostid module parameter. zgenhostid will not replace
an existing /etc/hostid file, so new mmp_clear_hostid calls are
required.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6358Closes#6379
Add multihost=on|off pool property to control MMP. When enabled
a new thread writes uberblocks to the last slot in each label, at a
set frequency, to indicate to other hosts the pool is actively imported.
These uberblocks are the last synced uberblock with an updated
timestamp. Property defaults to off.
During tryimport, find the "best" uberblock (newest txg and timestamp)
repeatedly, checking for change in the found uberblock. Include the
results of the activity test in the config returned by tryimport.
These results are reported to user in "zpool import".
Allow the user to control the period between MMP writes, and the
duration of the activity test on import, via a new module parameter
zfs_multihost_interval. The period is specified in milliseconds. The
activity test duration is calculated from this value, and from the
mmp_delay in the "best" uberblock found initially.
Add a kstat interface to export statistics about Multiple Modifier
Protection (MMP) updates. Include the last synced txg number, the
timestamp, the delay since the last MMP update, the VDEV GUID, the VDEV
label that received the last MMP update, and the VDEV path. Abbreviated
output below.
$ cat /proc/spl/kstat/zfs/mypool/multihost
31 0 0x01 10 880 105092382393521 105144180101111
txg timestamp mmp_delay vdev_guid vdev_label vdev_path
20468 261337 250274925 68396651780 3 /dev/sda
20468 261339 252023374 6267402363293 1 /dev/sdc
20468 261340 252000858 6698080955233 1 /dev/sdx
20468 261341 251980635 783892869810 2 /dev/sdy
20468 261342 253385953 8923255792467 3 /dev/sdd
20468 261344 253336622 042125143176 0 /dev/sdab
20468 261345 253310522 1200778101278 2 /dev/sde
20468 261346 253286429 0950576198362 2 /dev/sdt
20468 261347 253261545 96209817917 3 /dev/sds
20468 261349 253238188 8555725937673 3 /dev/sdb
Add a new tunable zfs_multihost_history to specify the number of MMP
updates to store history for. By default it is set to zero meaning that
no MMP statistics are stored.
When using ztest to generate activity, for automated tests of the MMP
function, some test functions interfere with the test. For example, the
pool is exported to run zdb and then imported again. Add a new ztest
function, "-M", to alter ztest behavior to prevent this.
Add new tests to verify the new functionality. Tests provided by
Giuseppe Di Natale.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#745Closes#6279
Currently, there is no way to pause a scrub. Pausing may
be useful when the pool is busy with other I/O to preserve
bandwidth.
This patch adds the ability to pause and resume scrubbing.
This is achieved by maintaining a persistent on-disk scrub state.
While the state is 'paused' we do not scrub any more blocks.
We do however perform regular scan housekeeping such as
freeing async destroyed and deadlist blocks while paused.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Serapheim Dimitropoulos <serapheimd@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6167
This addition will enable us to sync an open TXG to the main pool
on demand. The functionality is similar to 'sync(2)' but 'zpool sync'
will return when data has hit the main storage instead of potentially
just the ZIL as is the case with the 'sync(2)' cmd.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6122
This patch adds a '-f' option to 'zpool offline' to fault a vdev
instead of bringing it offline. Unlike the OFFLINE state, the
FAULTED state will trigger the FMA code, allowing for things like
autoreplace and triggering the slot fault LED. The -f faults
persist across imports, unless they were set with the temporary
(-t) flag. Both persistent and temporary faults can be cleared
with zpool clear.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6094
This commit allow higher ashift values (up to 16) in 'zpool create'
The ashift value was previously limited to 13 (8K block) in b41c990
because the limited number of uberblocks we could fit in the
statically sized (128K) vdev label ring buffer could prevent the
ability the safely roll back a pool to recover it.
Since b02fe35 the largest uberblock size we support is 8K: this
allow us to store a minimum number of 16 uberblocks in the vdev
label, even with higher ashift values.
Additionally change 'ashift' pool property behaviour: if set it will
be used as the default hint value in subsequent vdev operations
('zpool add', 'attach' and 'replace'). A custom ashift value can still
be specified from the command line, if desired.
Finally, fix a bug in add-o_ashift.ksh caused by a missing variable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2024Closes#4205Closes#4740Closes#5763
* Add zfs_nicebytes() to print human-readable sizes
Some 'zfs', 'zpool' and 'zdb' output strings can be confusing to the
user when no units are specified. This add a new zfs_nicenum_format
"ZFS_NICENUM_BYTES" used to print bytes in their human-readable form.
Additionally, update some test cases to use machine-parsable 'zfs get'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2414Closes#3185Closes#3594Closes#6032
Authored by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Updated 'zpool labelclear' and 'zdb -l' such that they attempt
to find a vdev given solely its short name. This behavior is
consistent with the upstream OpenZFS code and the test cases
depend on it. The actual implementation differs slightly due
to device naming conventions on Linux.
- auto_online_001_pos, auto_replace_001_pos and add-o_ashift
test cases updated to expect failure when no label exists.
- read_efi_label() and zpool_label_disk_check() are read-only
operations and should use O_RDONLY at open time to enforce this.
- zpool_label_disk() and zpool_relabel_disk() write the partition
information using O_DIRECT an fsync() and page cache invalidation
to ensure a consistent view of the device.
- dump_label() in zdb should invalidate the page cache in order
to get the authoritative label from disk.
OpenZFS-issue: https://www.illumos.org/issues/6865
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c95076cCloses#5981
df83110 added the ability to specify a custom "ashift" value from the command
line in 'zpool add' and 'zpool attach'. This commit adds additional checks to
the provided ashift to prevent invalid values from being used, which could
result in disastrous consequences for the whole pool.
Additionally provide ASHIFT_MAX and ASHIFT_MIN definitions in spa.h.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#5878
When a pool is suspended it's impossible to read the list
of damaged files from disk. This would result in a generic
misleading "insufficient permissions" error message.
Update zpool_get_errlog() to use the standard zpool error
logging functions to generate a useful error message. In
this case:
errors: List of errors unavailable: pool I/O is currently suspended
This patch does not address the related issue of potentially
not being able to resume a suspend pool when the underlying
device names have changed.
Additionally, remove the error handling from zfs_alloc()
in zpool_get_errlog() for readability since this function
can never fail.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4031Closes#5731Closes#5907
Correctly handle the unlikely case where the memory buffer cannot be resized.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#5575
Authored by: Toomas Soome <tsoome@me.com>
Reviewed by: - George Wilson <george.wilson@delphix.com>
Reviewed by: - Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: - Andrew Stormont <andyjstormont@gmail.com>
Reviewed by: - Albert Lee <trisk@omniti.com>
Approved by: - Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/5142
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/d5f26adCloses#5663
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5547Closes#5543
Enable picky cstyle checks and resolve the new warnings. The vast
majority of the changes needed were to handle minor issues with
whitespace formatting. This patch contains no functional changes.
Non-whitespace changes are as follows:
* 8 times ; to { } in for/while loop
* fix missing ; in cmd/zed/agents/zfs_diagnosis.c
* comment (confim -> confirm)
* change endline , to ; in cmd/zpool/zpool_main.c
* a number of /* BEGIN CSTYLED */ /* END CSTYLED */ blocks
* /* CSTYLED */ markers
* change == 0 to !
* ulong to unsigned long in module/zfs/dsl_scan.c
* rearrangement of module_param lines in module/zfs/metaslab.c
* add { } block around statement after for_each_online_node
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5465
This patch adds a command (-c) option to zpool status and zpool iostat. The
-c option allows you to run an arbitrary command on each vdev and display
the first line of output in zpool status/iostat. The environment vars
VDEV_PATH and VDEV_UPATH are set to the vdev's path and "underlying path"
before running the command. For device mapper, multipath, or partitioned
vdevs, VDEV_UPATH is the actual underlying /dev/sd* disk. This can be useful
if the command you're running requires a /dev/sd* device.
The patch also uses /sys/block/<dev>/slaves/ to lookup the underlying device
instead of using libdevmapper. This not only removes the libdevmapper
requirement at build time, but also allows you to resolve device mapper
devices without being root. This means that UDEV_UPATH get set correctly
when running zpool status/iostat as an unprivileged user.
Example:
$ zpool status -c 'echo I am $VDEV_PATH, $VDEV_UPATH'
NAME STATE READ WRITE CKSUM
mypool ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
mpatha ONLINE 0 0 0 I am /dev/mapper/mpatha, /dev/sdc
sdb ONLINE 0 0 0 I am /dev/sdb1, /dev/sdb
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5368
Sometimes it is desirable to specifically disable one or several
features directly on the 'zpool create' command line.
$ zpool create -o feature@<feature>=disabled ...
Original-patch-by: Turbo Fredriksson <turbo@bayour.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3460Closes#5142Closes#5324
Previously when a drive faulted, the statechange-led.sh script would lookup
the drive's LED sysfs entry in /sys/block/sd*/device/enclosure_device, and
turn it on. During testing we noticed that if you pulled out a drive, or if
the drive was so badly broken that it no longer appeared to Linux, that the
/sys/block/sd* path would be removed, and the script could not lookup the
LED entry.
To fix this, this patch looks up the disks's more persistent
"/sys/class/enclosure/X:X:X:X/Slot N" LED sysfs path at pool import. It then
passes that path to the statechange-led script to use, rather than having the
script look it up on the fly. This allows the script to turn on/off the slot
LEDs even when the drive is missing.
Closes#5309Closes#2375
1. Enable multipath autoreplace support for FMA.
This extends FMA autoreplace to work with multipath disks. This
requires libdevmapper to be installed at build time.
2. Turn on/off fault LEDs when VDEVs become degraded/faulted/online
Set ZED_USE_ENCLOSURE_LEDS=1 in zed.rc to have ZED turn on/off the enclosure
LED for a drive when a drive becomes FAULTED/DEGRADED. Your enclosure must
be supported by the Linux SES driver for this to work. The enclosure LED
scripts work for multipath devices as well. The scripts will clear the LED
when the fault is cleared.
3. Rate limit ZIO delay and checksum events so as not to flood ZED
ZIO delay and checksum events are rate limited to 5/sec in the zfs module.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#2449Closes#3017Closes#5159
The error message in zpool_vdev_remove() said top-level devices
could be removed, but that has never been true.
Reported-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#4506Closes#5213
This first phase brings over the ZFS SLM module, zfs_mod.c, to handle
auto operations in response to disk events. Disk event monitoring is
provided from libudev and generates the expected payload schema for
zfs_mod. This work leverages the recently added devid and phys_path
strings in the vdev label.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#4673
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Calling dsl_dataset_name on a dataset with a 256 byte buffer is asking
for trouble. We should check every dataset on import, using a 1024 byte
buffer and checking each time to see if the dataset's new name is longer
than 256 bytes.
OpenZFS-issue: https://www.illumos.org/issues/6876
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ca8674e
Add argument format to print_one_column(), and use it to call
zfs_nicenum_format with, instead of just zfs_nicenum. Don't print "%"
for fragmentation or capacity percent values.
The calls to print_one_colum is made with ZFS_NICENUM_RAW if
cb->cb_literal (zpool list called with -p), and ZFS_NICENUM_1024 if not.
Also zpool_get_prop is modified to don't add "%" or "x" if literal.
Signed-off-by: Christer Ekholm <che@chrekh.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov
Closes#4657
3993 zpool(1M) and zfs(1M) should support -p for "list" and "get"
4700 "zpool get" doesn't support -H or -o options
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/3993
OpenZFS-issue: https://www.illumos.org/issues/4700
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c58b352
Porting notes:
I removed ZoL's zpool_get_prop_literal() in favor of
zpool_get_prop(..., boolean_t literal) since that's what OpenZFS
uses. The functionality is the same.
6659 nvlist_free(NULL) is a no-op
Reviewed by: Toomas Soome <tsoome@me.com>
Reviewed by: Marcel Telka <marcel@telka.sk>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/6659https://github.com/illumos/illumos-gate/commit/aab83bb
Ported-by: David Quigley <dpquigl@davequigley.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4566
When ZFS partitions a block device it must wait for udev to create
both a device node and all the device symlinks. This process takes
a variable length of time and depends on factors such how many links
must be created, the complexity of the rules, etc. Complicating
the situation further it is not uncommon for udev to create and
then remove a link multiple times while processing the udev rules.
Given the above, the existing scheme of waiting for an expected
partition to appear by name isn't 100% reliable. At this point
udev may still remove and recreate think link resulting in the
kernel modules being unable to open the device.
In order to address this the zpool_label_disk_wait() function
has been updated to use libudev. Until the registered system
device acknowledges that it in fully initialized the function
will wait. Once fully initialized all device links are checked
and allowed to settle for 50ms. This makes it far more likely
that all the device nodes will exist when the kernel modules
need to open them.
For systems without libudev an alternate zpool_label_disk_wait()
was updated to include a settle time. In addition, the kernel
modules were updated to include retry logic for this ENOENT case.
Due to the improved checks in the utilities it is unlikely this
logic will be invoked. However, if the rare event it is needed
it will prevent a failure.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#4523Closes#3708Closes#4077Closes#4144Closes#4214Closes#4517
When partitioning a device a name may be specified for each partition.
Internally zfs doesn't use this partition name for anything so it
has always just been set to "zfs".
However this isn't optimal because udev will create symlinks using
this name in /dev/disk/by-partlabel/. If the name isn't unique
then all the links cannot be created.
Therefore a random 64-bit value has been added to the partition
label, i.e "zfs-1234567890abcdef". Additional information could
be encoded here but since partitions may be reused that might
result in confusion and it was decided against.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#4517
This is foundational work for ZED.
Updates a leaf vdev's persistent device strings on Linux platform
* only applies for a dedicated leaf vdev (aka whole disk)
* updated during pool create|add|attach|import
* used for matching device matching during auto-{online,expand,replace}
* stored in a leaf disk config label (i.e. alongside 'path' NVP)
* can opt-out using env var ZFS_VDEV_DEVID_OPT_OUT=YES
Some examples:
path: '/dev/sdb1'
devid: 'scsi-350000394a8ca4fbc-part1'
phys_path: 'pci-0000:04:00.0-sas-0x50000394a8ca4fbf-lun-0'
path: '/dev/mapper/mpatha'
devid: 'dm-uuid-mpath-35000c5006304de3f'
Signed-off-by: Don Brady <don.brady@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2856Closes#3978Closes#4416
The following options have been added to the zpool add, iostat,
list, status, and split subcommands. The default behavior was
not modified, from zfs(8).
-g Display vdev GUIDs instead of the normal short
device names. These GUIDs can be used in-place of
device names for the zpool detach/off‐
line/remove/replace commands.
-L Display real paths for vdevs resolving all symbolic
links. This can be used to lookup the current block
device name regardless of the /dev/disk/ path used
to open it.
-p Display full paths for vdevs instead of only the
last component of the path. This can be used in
conjunction with the -L flag.
This behavior may also be enabled using the following environment
variables.
ZPOOL_VDEV_NAME_GUID
ZPOOL_VDEV_NAME_FOLLOW_LINKS
ZPOOL_VDEV_NAME_PATH
This change is based on worked originally started by Richard Yao
to add a -g option. Then extended by @ilovezfs to add a -L option
for openzfsonosx. Those changes have been merged, re-factored,
a -p option added and extended to all relevant zpool subcommands.
Original-patch-by: Richard Yao <ryao@gentoo.org>
Extended-by: ilovezfs <ilovezfs@icloud.com>
Extended-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: ilovezfs <ilovezfs@icloud.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2011Closes#4341
5518 Memory leaks in libzfs import implementation
Reviewed by: Dan Fields <dan.fields@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Serghei Samsi <sscdvp@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/5518https://github.com/illumos/illumos-gate/commit/078266a
Porting notes:
- One hunk of this change was already applied independently in
commit 4def05f.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
6298 zfs_create_008_neg and zpool_create_023_neg need to be updated
for large block support
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/6298https://github.com/illumos/illumos-gate/commit/e9316f7
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4217
We fail to make partitions on xvd (Xen Virtual Block) devices. This also
causes debug builds of zpool create to return an error when given xen
virtual block devices. These devices should be given the same treatment
as vd (KVM Virtual Block) devices, so we adjust the relevant code paths.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3576
Creating virtual machines that have their rootfs on ZFS on hosts that
have their rootfs on ZFS causes SPA namespace collisions when the
standard name rpool is used. The solution is either to give each guest
pool a name unique to the host, which is not always desireable, or boot
a VM environment containing an ISO image to install it, which is
cumbersome.
26b42f3f9d introduced `zpool import -t
...` to simplify situations where a host must access a guest's pool when
there is a SPA namespace conflict. We build upon that to introduce
`zpool import -t tname ...`. That allows us to create a pool whose
in-core name is tname, but whose on-disk name is the normal name
specified.
This simplifies the creation of machine images that use a rootfs on ZFS.
That benefits not only real world deployments, but also ZFSOnLinux
development by decreasing the time needed to perform rootfs on ZFS
experiments.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2417
5116 zpool history -i goes into infinite loop
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Richard Elling <richard.elling@gmail.com>
Reviewed by: Boris Protopopov <boris.protopopov@me.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/5116https://github.com/illumos/illumos-gate/commit/3339867
Ported by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2715
The 'zpool list -v' command displays lots of info but excludes the
capacity of each disk. This should be added.
5147 zpool list -v should show individual disk capacity
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Matthew Ahrens <matthew.ahrens@delphix.com>
Reviewed by: Richard Elling <richard.elling@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/5147https://github.com/illumos/illumos-gate/commit/7a09f97
Ported by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2688
When com.delphix:spacemap_histogram is disabled, the value of
fragmentation was printing as 18446744073709551615 (UINT64_MAX),
when it should print as '-'.
The issue was caused by a small mistake during the merge of
"4980 metaslabs should have a fragmentation metric."
upstream: https://github.com/illumos/illumos-gate/commit/2e4c998
ZoL: https://github.com/zfsonlinux/zfs/commit/f3a7f66
The problem is in zpool_get_prop_literal, where the handling of the
pool property ZPOOL_PROP_FRAGMENTATION was added to wrong the
section. In particular, ZPOOL_PROP_FRAGMENTATION should not be in
the section where zpool_get_state(zhp) == POOL_STATE_UNAVAIL, but
lower down after it's already been determined that the pool is in
fact available, which is where upstream illumos correctly has had
it.
Thanks to lundman for helping to track down this bug.
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2664
4976 zfs should only avoid writing to a failing non-redundant top-level vdev
4978 ztest fails in get_metaslab_refcount()
4979 extend free space histogram to device and pool
4980 metaslabs should have a fragmentation metric
4981 remove fragmented ops vector from block allocator
4982 space_map object should proactively upgrade when feature is enabled
4983 need to collect metaslab information via mdb
4984 device selection should use fragmentation metric
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
https://www.illumos.org/issues/4976https://www.illumos.org/issues/4978https://www.illumos.org/issues/4979https://www.illumos.org/issues/4980https://www.illumos.org/issues/4981https://www.illumos.org/issues/4982https://www.illumos.org/issues/4983https://www.illumos.org/issues/4984https://github.com/illumos/illumos-gate/commit/2e4c998
Notes:
The "zdb -M" option has been re-tasked to display the new metaslab
fragmentation metric and the new "zdb -I" option is used to control
the maximum number of in-flight I/Os.
The new fragmentation metric is derived from the space map histogram
which has been rolled up to the vdev and pool level and is presented
to the user via "zpool list".
Add a number of module parameters related to the new metaslab weighting
logic.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2595
4914 zfs on-disk bookmark structure should be named *_phys_t
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Saso Kiselkov <skiselkov.ml@gmail.com>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/4914https://github.com/illumos/illumos-gate/commit/7802d7b
Porting notes:
There were a number of zfsonlinux-specific uses of zbookmark_t which
needed to be updated. This should reduce the likelihood of further
problems like issue #2094 from occurring.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2558
4390 i/o errors when deleting filesystem/zvol can lead to space map corruption
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/4390https://github.com/illumos/illumos-gate/commit/7fd05ac
Porting notes:
Previous stack-reduction efforts in traverse_visitb() caused a fair
number of un-mergable pieces of code. This patch should reduce its
stack footprint a bit more.
The new local bptree_entry_phys_t in bptree_add() is dynamically-allocated
using kmem_zalloc() for the purpose of stack reduction.
The new global zfs_free_leak_on_eio has been defined as an integer
rather than a boolean_t as was the case with the related zfs_recover
global. Also, zfs_free_leak_on_eio's definition has been inserted into
zfs_debug.c for consistency with the existing definition of zfs_recover.
Illumos placed it in spa_misc.c.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2545
4171 clean up spa_feature_*() interfaces
4172 implement extensible_dataset feature for use by other zpool features
Reviewed by: Max Grossman <max.grossman@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Approved by: Garrett D'Amore <garrett@damore.org>a
References:
https://www.illumos.org/issues/4171https://www.illumos.org/issues/4172https://github.com/illumos/illumos-gate/commit/2acef22
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2528
When adding or replacing a vdev with a different sector size the
error message should be more useful. In addition to describing
the problem provide a hint that the '-o ashift' option can be
used to override the optimal default value.
Since using a non-optimal value may incur a significant performance
penalty we should issue this error. But there a numerous reasons
why a administrator may wish to do this anyway.
Signed-off-by: Niklas Edmundsson <ZNikke@github>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2421
Several of the zfs utilities allow you to pass a vdev's guid rather
than the device name. However, the utilities are not consistent in
how they parse that guid. For example, 'zinject' expects the guid
to be passed as a hex value while 'zpool replace' wants it as a
decimal. The user is forced to just know what format to use.
This patch improve things by making the parsing more tolerant.
When strtol(3) is called using 0 for the base, rather than say
10 or 16, it will then accept hex, decimal, or octal input based
on the prefix. From the man page.
If base is zero or 16, the string may then include a "0x"
prefix, and the number will be read in base 16; otherwise,
a zero base is taken as 10 (decimal) unless the next character
is '0', in which case it is taken as 8 (octal).
NOTE: There may be additional conversions not caught be this patch.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Issue #2
zpool_events_next() can be called in blocking mode by specifying a
non-zero value for the "block" parameter. However, the design of
the ZFS Event Daemon (zed) requires additional functionality from
zpool_events_next(). Instead of adding additional arguments to the
function, it makes more sense to use flags that can be bitwise-or'd
together.
This commit replaces the zpool_events_next() int "block" parameter with
an unsigned bitwise "flags" parameter. It also defines ZEVENT_NONE
to specify the default behavior. Since non-blocking mode can be
specified with the existing ZEVENT_NONBLOCK flag, the default behavior
becomes blocking mode. This, in effect, inverts the previous use
of the "block" parameter. Existing callers of zpool_events_next()
have been modified to check for the ZEVENT_NONBLOCK flag.
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2
Due to the very poorly chosen argument name 'cleanup_fd' it was
completely unclear that this file descriptor is used to track the
current cursor location. When the file descriptor is created by
opening ZFS_DEV a private cursor is created in the kernel for the
returned file descriptor. Subsequent calls to zpool_events_next()
and zpool_events_seek() then require the file descriptor as an
argument to reposition the cursor. When the file descriptor is
closed the kernel state tracking the cursor is destroyed.
This patch contains no functional change, it just changes a
few variable names and clarifies the documentation.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Issue #2
The ZFS_IOC_EVENTS_SEEK ioctl was added to allow user space callers
to seek around the zevent file descriptor by EID. When a specific
EID is passed and it exists the cursor will be positioned there.
If the EID is no longer cached by the kernel ENOENT is returned.
The caller may also pass ZEVENT_SEEK_START or ZEVENT_SEEK_END to seek
to those respective locations.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Issue #2
The vast majority of these changes are in Linux specific code.
They are the result of not having an automated style checker to
validate the code when it was originally written. Others were
caused when the common code was slightly adjusted for Linux.
This patch contains no functional changes. It only refreshes
the code to conform to style guide.
Everyone submitting patches for inclusion upstream should now
run 'make checkstyle' and resolve any warning prior to opening
a pull request. The automated builders have been updated to
fail a build if when 'make checkstyle' detects an issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1821
Under Linux this restriction does not apply because we have access
to all the required devices.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1631
3745 zpool create should treat -O mountpoint and -m the same
3811 zpool create -o altroot=/xyz -O mountpoint=/mnt ignores
the mountpoint option
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Christopher Siden <christopher.siden@delphix.com>
References:
https://www.illumos.org/issues/3745https://www.illumos.org/issues/3811illumos/illumos-gate@8b71377531
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
This change introduces zpool_get_prop_literal. It's an expanded version
of zpool_get_prop taking one additional boolean parameter. With this
parameter set to B_FALSE it will behave identically to zpool_get_prop.
Setting it to B_TRUE will return full precision numbers for the
following properties:
ZPOOL_PROP_SIZE
ZPOOL_PROP_ALLOCATED
ZPOOL_PROP_FREE
ZPOOL_PROP_FREEING
ZPOOL_PROP_EXPANDSZ
ZPOOL_PROP_ASHIFT
Also introduced is a wrapper function for zpool_get_prop making it
use zpool_get_prop_literal in the background.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1813
2882 implement libzfs_core
2883 changing "canmount" property to "on" should not always remount dataset
2900 "zfs snapshot" should be able to create multiple, arbitrary snapshots at once
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Chris Siden <christopher.siden@delphix.com>
Reviewed by: Garrett D'Amore <garrett@damore.org>
Reviewed by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Dan Kruchinin <dan.kruchinin@gmail.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
https://www.illumos.org/issues/2882https://www.illumos.org/issues/2883https://www.illumos.org/issues/2900illumos/illumos-gate@4445fffbbb
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1293
Porting notes:
WARNING: This patch changes the user/kernel ABI. That means that
the zfs/zpool utilities built from master are NOT compatible with
the 0.6.2 kernel modules. Ensure you load the matching kernel
modules from master after updating the utilities. Otherwise the
zfs/zpool commands will be unable to interact with your pool and
you will see errors similar to the following:
$ zpool list
failed to read pool configuration: bad address
no pools available
$ zfs list
no datasets available
Add zvol minor device creation to the new zfs_snapshot_nvl function.
Remove the logging of the "release" operation in
dsl_dataset_user_release_sync(). The logging caused a null dereference
because ds->ds_dir is zeroed in dsl_dataset_destroy_sync() and the
logging functions try to get the ds name via the dsl_dataset_name()
function. I've got no idea why this particular code would have worked
in Illumos. This code has subsequently been completely reworked in
Illumos commit 3b2aab1 (3464 zfs synctask code needs restructuring).
Squash some "may be used uninitialized" warning/erorrs.
Fix some printf format warnings for %lld and %llu.
Apply a few spa_writeable() changes that were made to Illumos in
illumos/illumos-gate.git@cd1c8b8 as part of the 3112, 3113, 3114 and
3115 fixes.
Add a missing call to fnvlist_free(nvl) in log_internal() that was added
in Illumos to fix issue 3085 but couldn't be ported to ZoL at the time
(zfsonlinux/zfs@9e11c73) because it depended on future work.
The FreeBSD implementation of zfs adds the 'zpool labelclear'
command. Since this functionality is helpful and straight
forward to add it is being included in ZoL.
References:
freebsd/freebsd@119a041dc9
Ported-by: Dmitry Khasanov <pik4ez@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1126
2619 asynchronous destruction of ZFS file systems
2747 SPA versioning with zfs feature flags
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <gwilson@delphix.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Dan Kruchinin <dan.kruchinin@gmail.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
illumos/illumos-gate@53089ab7c8illumos/illumos-gate@ad135b5d64
illumos changeset: 13700:2889e2596bd6
https://www.illumos.org/issues/2619https://www.illumos.org/issues/2747
NOTE: The grub specific changes were not ported. This change
must be made to the Linux grub packages.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Commit 57a4edd allows the bootfs property to be set on any pool.
However, many of the zpool commands still prevent you from using
EFI labeled devices for the root pool. For example:
# zpool attach rpool /dev/sda /dev/sdb
cannot label 'sdb': EFI labeled devices are not supported on
root pools. on root devices.
For non-Solaris builds such as Linux disable this error.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1077
The 'zpool replace' command would fail when given a short name
because unlike on other platforms the short name cannot be
deterministically expanded to a single path. Multiple path
prefixes must be checked and in addition the partition suffix
for whole disks is determined by the prefix.
To handle this complexity a zfs_strcmp_pathname() function was
added which takes either a short or fully qualified device name.
Short names will be expanded using the prefixes in the default
import search path, or the ZPOOL_IMPORT_PATH environment variable
if it's defined. All posible expansions are then compared against
the comparison path. Care is taken to strip redundant slashes to
ensure legitimate matches are not missed.
In the context of this work the existing zfs_resolve_shortname()
function was extended to consider the ZPOOL_IMPORT_PATH when set.
The zfs_append_partition() interface was also simplified to take
only a single buffer.
The vast majority of these changes rework existing Linux specific
code which was originally written to accomidate udev. However,
there is some minimal cleanup which removes Illumos specific code.
This was done to improve readability but the basic flow and intent
of the upstream code was maintained.
These changes are the logical conclusion of the previos work to
adjust the 'zpool import' search behavior, see commit 44867b6a.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#544Closes#976
Commit 858219c makes more sense down below in the 'if (verbose)'
section of the code. Initially, buf and path will never point
to the same location. Once 'path = buf' is set on a raidz vdev,
the code may drop into the verbose section depending on the
verbose flag. In here, using a tmpbuf makes sense since now
'buf == path'.
This issue does not occur in the upstream Solaris code because
their implementations of snprintf() allow for buf and path to
be the same address.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#57
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/1693
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#678
Currently, zpool online -e (dynamic vdev expansion) doesn't work on
whole disks because we're invoking ioctl(BLKRRPART) from userspace
while ZFS still has a partition open on the disk, which results in
EBUSY.
This patch moves the BLKRRPART invocation from the zpool utility to the
module. Specifically, this is done just before opening the device in
vdev_disk_open() which is called inside vdev_reopen(). This requires
jumping through some hoops to get to the disk device from the partition
device, and to make sure we can still open the partition after the
BLKRRPART call.
Note that this new code path is triggered on dynamic vdev expansion
only; other actions, like creating a new pool, are unchanged and still
call BLKRRPART from userspace.
This change also depends on API changes which are available in 2.6.37
and latter kernels. The build system has been updated to detect this,
but there is no compatibility mode for older kernels. This means that
online expansion will NOT be available in older kernels. However, it
will still be possible to expand the vdev offline.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#808
Currently, zpool_vdev_online() calls zpool_relabel_disk() with a short
partition device name, which is obviously wrong because (1)
zpool_relabel_disk() expects a full, absolute path to use with open()
and (2) efi_write() must be called on an opened disk device, not a
partition device.
With this patch, zpool_relabel_disk() gets called with a full disk
device path. The path is determined using the same algorithm as
zpool_find_vdev().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #808
The error handling code around zpool_relabel_disk() is either inexistent
or wrong. The function call itself is not checked, and
zpool_relabel_disk() is generating error messages from an unitialized
buffer.
Before:
# zpool online -e homez sdb; echo $?
`: cannot relabel 'sdb1': unable to open device: 2
0
After:
# zpool online -e homez sdb; echo $?
cannot expand sdb: cannot relabel 'sdb1': unable to open device: 2
1
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #808
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Alexander Eremin <alexander.eremin@nexenta.com>
Reviewed by: Alexander Stetsenko <ams@nexenta.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/1748
This commit modifies the user to kernel space ioctl ABI. Extra
care should be taken when updating to ensure both the kernel
modules and utilities are updated. If only the user space
component is updated both the 'zpool events' command and the
'zpool reguid' command will not work until the kernel modules
are updated.
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#665
When a device is already open O_EXCL by another process the
`zpool import` will correctly fail. However, the default failure
message isn't very helpful. It may in fact be harmful if you
take its advise and destroy your pool.
cannot import 'tank': pool is busy
Destroy and re-create the pool from
a backup source.
Improve the error message in the EBUSY case to simply print a
message indicating that the devices are current in use. The user
will need to manually identify which process has the device open
exclusively and why.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Some devices have exhibited sensitivity to the ending alignment of
partitions. In particular, even if the first partition begins at 1
MiB, we have seen many sd driver task abort errors with certain SSDs
if the first partition doesn't end on a 1 MiB boundary. This occurs
when the vdev label is read during pool creation or importation and
causes a delay of about 30 seconds per device. It can also be
simulated with dd when the pool isn't imported:
dd if=/dev/sda1 of=/dev/null bs=262144 count=1
For the record, this problem was observed with SMARTMOD
SG9XCA2E200GE01 200GB SSDs. Unfortunately I don't have a good
explanation for this behavior. It seems to have something to do with
highly fragmented single-sector requests being issued to the device,
which it may not support. With end-aligned partitions at least
page-sized requests were queued and issued to the driver according
to blktrace. In any case, aligning the partition end is a fairly
innocuous work-around, wasting at most 1 MiB of space.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#574
New SSDs are now available which use an internal 8k block size.
To make sure ZFS can get the maximum performance out of these
devices we're increasing the maximum ashift to 13 (8KB).
This value is still small enough that we can fit 16 uberblocks
in the vdev ring label. However, I don't want to increase this
any futher or it will limit the ability the safely roll back a
pool to recover it.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#565
Commit zfsonlinux/zfs@57a4eddc4d
allows the bootfs property to be set on any pool, but does not
accommodate subsequent vdev changes. For example:
# zpool replace rpool /dev/sda /dev/sdb
operation not supported on this type of pool
property 'bootfs' is not supported on EFI labeled devices
For non-Solaris builds, disable the check that emits this error.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
While we initially allowed you to set your ashift as large as 17
(SPA_MAXBLOCKSIZE) that is actually unsafe. What wasn't considered
at the time is that each uberblock written to the vdev label ring
buffer will be of this size. Now the buffer is statically sized
to 128k and we need to be able to fit several uberblocks in it.
With a large ashift that becomes a problem.
Therefore I'm reducing the maximum configurable ashift value to 12.
This is large enough for the 4k sector drives and small enough that
we can still keep the most recent 32 uberblock in the vdev label
ring buffer.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#425
Some disks with internal sectors larger than 512 bytes (e.g., 4k) can
suffer from bad write performance when ashift is not configured
correctly. This is caused by the disk not reporting its actual sector
size, but a sector size of 512 bytes. The drive may behave this way
for compatibility reasons. For example, the WDC WD20EARS disks are
known to exhibit this behavior.
When creating a zpool, ZFS takes that wrong sector size and sets the
"ashift" property accordingly (to 9: 1<<9=512), whereas it should be
set to 12 for 4k sectors (1<<12=4096).
This patch allows an adminstrator to manual specify the known correct
ashift size at 'zpool create' time. This can significantly improve
performance in certain cases. However, it will have an impact on your
total pool capacity. See the updated ashift property description
in the zpool.8 man page for additional details.
Valid values for the ashift property range from 9 to 17 (512B-128KB).
Additionally, you may set the ashift to 0 if you wish to auto-detect
the sector size based on what the disk reports, this is the default
behavior. The most common ashift values are 9 and 12.
Example:
zpool create -o ashift=12 tank raidz2 sda sdb sdc sdd
Closes#280
Original-patch-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
zpool status displays abbreviated vdev names without leading path components
and, in the case of whole disks, without partition information. Also, the
zpool subcommands 'create' and 'add' support using shorthand devices names
without qualified paths. Prior to this change, however, removing a device
generally required specifying its name as it is stored in the vdev label. So
while zpool status might list a cache disk with a name like A16, removing it
would require a full path such as /dev/disk/zpool/A16-part1, which is
non-intuitive.
This change adds support for shorthand device names with the remove subcommand
so one can simply type, for example,
zpool remove tank A16
A consequence of this change is that including the partition information when
removing a whole-disk vdev now results in an error. While this is arguably the
correct behavior, it is a departure from how zpool previously worked in this
project.
This change removes the only reference to ctd_check_path(), so that function is
also removed to avoid compiler warnings.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Under Solaris, the slice number is chopped off when displaying the device name
if the vdev is a whole disk. Under Linux we should similarly discard the
partition number. This commit adds the logic to perform the name truncation
for devices ending in -partX, XpX, or X, where X is a string of digits. The
second case handles devices like md0p0. The third case is limited to scsi and
ide disks, i.e. those beginning with "sd" or "hd", in order to avoid stripping
the number from names like "loop0".
This commit removes the Solaris-specific code for removing slices, since we no
longer reasonably expect our changes to be merged in upstream. The partition
stripping code was moved off to a helper function to improve readability.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Top-level vdev names in zpool status output should follow a <type-id> naming
convention. In the case of raidz devices, the type portion of the name was
missing.
This commit fixes a bug in zpool_vdev_name() where in this snprintf call
(void) snprintf(buf, sizeof (buf), "%s-%llu", path,
(u_longlong_t)id);
buf and path may point to the same location. The result is that buf ends up
containing only the "-id" part. This only occurred for raidz devices because
the code for appending the parity level to the type string stored its result in
buf then set path to point there. To fix this we allocate a new temporary
buffer on the stack instead of reusing buf.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#57
This topic branch contains all the changes needed to integrate the user
side zfs tools with Linux style devices. Primarily this includes fixing
up the Solaris libefi library to be Linux friendly, and integrating with
the libblkid library which is provided by e2fsprogs.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This topic branch leverages the Solaris style FMA call points
in ZFS to create a user space visible event notification system
under Linux. This new system is called zevent and it unifies
all previous Solaris style ereports and sysevent notifications.
Under this Linux specific scheme when a sysevent or ereport event
occurs an nvlist describing the event is created which looks almost
exactly like a Solaris ereport. These events are queued up in the
kernel when they occur and conditionally logged to the console.
It is then up to a user space application to consume the events
and do whatever it likes with them.
To make this possible the existing /dev/zfs ABI has been extended
with two new ioctls which behave as follows.
* ZFS_IOC_EVENTS_NEXT
Get the next pending event. The kernel will keep track of the last
event consumed by the file descriptor and provide the next one if
available. If no new events are available the ioctl() will block
waiting for the next event. This ioctl may also be called in a
non-blocking mode by setting zc.zc_guid = ZEVENT_NONBLOCK. In the
non-blocking case if no events are available ENOENT will be returned.
It is possible that ESHUTDOWN will be returned if the ioctl() is
called while module unloading is in progress. And finally ENOMEM
may occur if the provided nvlist buffer is not large enough to
contain the entire event.
* ZFS_IOC_EVENTS_CLEAR
Clear are events queued by the kernel. The kernel will keep a fairly
large number of recent events queued, use this ioctl to clear the
in kernel list. This will effect all user space processes consuming
events.
The zpool command has been extended to use this events ABI with the
'events' subcommand. You may run 'zpool events -v' to output a
verbose log of all recent events. This is very similar to the
Solaris 'fmdump -ev' command with the key difference being it also
includes what would be considered sysevents under Solaris. You
may also run in follow mode with the '-f' option. To clear the
in kernel event queue use the '-c' option.
$ sudo cmd/zpool/zpool events -fv
TIME CLASS
May 13 2010 16:31:15.777711000 ereport.fs.zfs.config.sync
class = "ereport.fs.zfs.config.sync"
ena = 0x40982b7897700001
detector = (embedded nvlist)
version = 0x0
scheme = "zfs"
pool = 0xed976600de75dfa6
(end detector)
time = 0x4bec8bc3 0x2e5aed98
pool = "zpios"
pool_guid = 0xed976600de75dfa6
pool_context = 0x0
While the 'zpool events' command is handy for interactive debugging
it is not expected to be the primary consumer of zevents. This ABI
was primarily added to facilitate the addition of a user space
monitoring daemon. This daemon would consume all events posted by
the kernel and based on the type of event perform an action. For
most events simply forwarding them on to syslog is likely enough.
But this interface also cleanly allows for more sophisticated
actions to be taken such as generating an email for a failed drive.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
