Linux since 4.7 makes interface 'cpu_has_feature' to use jump labels on
powerpc if CONFIG_JUMP_LABEL_FEATURE_CHECKS is enabled, in this case
however the inline function references GPL-only symbol
'cpu_feature_keys'.
ZFS currently uses 'cpu_has_feature' either directly or indirectly from
several places; while it is unknown how this issue didn't break ZFS on
64-bit little-endian powerpc, it is known to break ZFS with many Linux
versions on both 32-bit and 64-bit big-endian powerpc.
Until this issue is fixed in Linux, we have to workaround it by
overriding affected inline functions without depending on
'cpu_feature_keys'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: WHR <msl0000023508@gmail.com>
Closes#14590
Clang's static analyzer pointed out that if we can pass a -1 array index
to copyname[copies] if there are no valid DVAs. This is an absurd
situation, but it suggests that we are missing an assertion, so we add
it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14575
Traditionally ARC adaptation was limited to MRU/MFU distribution. But
for years people with metadata-centric workload demanded mechanisms to
also manage data/metadata distribution, that in original ZFS was just
a FIFO. As result ZFS effectively got separate states for data and
metadata, minimum and maximum metadata limits etc, but it all required
manual tuning, was not adaptive and in its heart remained a bad FIFO.
This change removes most of existing eviction logic, rewriting it from
scratch. This makes MRU/MFU adaptation individual for data and meta-
data, same as the distribution between data and metadata themselves.
Since most of required states separation was already done, it only
required to make arcs_size state field specific per data/metadata.
The adaptation logic is still based on previous concept of ghost hits,
just now it balances ARC capacity between 4 states: MRU data, MRU
metadata, MFU data and MFU metadata. To simplify arc_c changes instead
of arc_p measured in bytes, this code uses 3 variable arc_meta, arc_pd
and arc_pm, representing ARC balance between metadata and data, MRU and
MFU for data, and MRU and MFU for metadata respectively as 32-bit fixed
point fractions. Since we care about the math result only when need to
evict, this moves all the logic from arc_adapt() to arc_evict(), that
reduces per-block overhead, since per-block operations are limited to
stats collection, now moved from arc_adapt() to arc_access() and using
cheaper wmsums. This also allows to remove ugly ARC_HDR_DO_ADAPT flag
from many places.
This change also removes number of metadata specific tunables, part of
which were actually not functioning correctly, since not all metadata
are equal and some (like L2ARC headers) are not really evictable.
Instead it introduced single opaque knob zfs_arc_meta_balance, tuning
ARC's reaction on ghost hits, allowing administrator give more or less
preference to metadata without setting strict limits.
Some of old code parts like arc_evict_meta() are just removed, because
since introduction of ABD ARC they really make no sense: only headers
referenced by small number of buffers are not evictable, and they are
really not evictable no matter what this code do. Instead just call
arc_prune_async() if too much metadata appear not evictable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14359
This fixes building ZFS for Linux 4.7+ powerpc* architecture, where
Linux was configured without CONFIG_ALTIVEC or CONFIG_VSX.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: WHR <msl0000023508@gmail.com>
Closes#14591
The intent is that this is like ENOTSUP, but specifically for when
something can't be done because we have no support for the requested
crypto parameters; eg unlocking a dataset or receiving a stream
encrypted with a suite we don't support.
Its not intended to be recoverable without upgrading ZFS itself.
If the request could be made to work by enabling a feature or modifying
some other configuration item, then some other code should be used.
load-key: In the future we might have more crypto suites (ie new values
for the `encryption` property. Right now trying to load a key on such
a future crypto suite will look up suite parameters off the end of the
crypto table, resulting in misbehaviour and/or crashes (or, with debug
enabled, trip the assertion in `zio_crypt_key_unwrap`).
Instead, lets check the value we got from the dataset, and if we can't
handle it, abort early.
recv: When receiving a raw stream encrypted with an unknown crypto
suite, `zfs recv` would report a generic `invalid backup stream`
(EINVAL). While technically correct, its not super helpful, so lets
ship a more specific error code and message.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#14577
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#14567
This commit changes the BLAKE3 implementation handling and
also the calls to it from the ztest command.
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
The skeleton file module/icp/include/generic_impl.c can be used for
iterating over different implementations of algorithms.
It is used by SHA256, SHA512 and BLAKE3 currently.
The Solaris SHA2 implementation got replaced with a version which is
based on public domain code of cppcrypto v0.10.
These assembly files are taken from current openssl master:
- sha256-x86_64.S: x64, SSSE3, AVX, AVX2, SHA-NI (x86_64)
- sha512-x86_64.S: x64, AVX, AVX2 (x86_64)
- sha256-armv7.S: ARMv7, NEON, ARMv8-CE (arm)
- sha512-armv7.S: ARMv7, NEON (arm)
- sha256-armv8.S: ARMv7, NEON, ARMv8-CE (aarch64)
- sha512-armv8.S: ARMv7, ARMv8-CE (aarch64)
- sha256-ppc.S: Generic PPC64 LE/BE (ppc64)
- sha512-ppc.S: Generic PPC64 LE/BE (ppc64)
- sha256-p8.S: Power8 ISA Version 2.07 LE/BE (ppc64)
- sha512-p8.S: Power8 ISA Version 2.07 LE/BE (ppc64)
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
These are added:
- zfs_neon_available() for arm and aarch64
- zfs_sha256_available() for arm and aarch64
- zfs_sha512_available() for aarch64
- zfs_shani_available() for x86_64
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Co-Authored-By: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Closes#13741
These are added:
- zfs_neon_available() for arm and aarch64
- zfs_sha256_available() for arm and aarch64
- zfs_sha512_available() for aarch64
- zfs_shani_available() for x86_64
Changes:
- simd_powerpc.h: change license from CDDL to BSD
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
We had three sha2.h headers in different places.
The FreeBSD version, the Linux version and the generic solaris version.
The only assembly used for acceleration was some old x86-64 openssl
implementation for sha256 within the icp module.
For FreeBSD the whole SHA2 files of FreeBSD were copied into OpenZFS,
these files got removed also.
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
With some pathological access patterns it is possible to make ZFS
accumulate almost unlimited amount of speculative prefetch ZIOs.
Combined with linear ABD allocations in RAIDZ code, it appears to
be possible to exhaust system KVA, triggering kernel panic.
Address this by introducing a system-wide counter of active prefetch
requests and blocking prefetch distance doubling per stream hits if
the number of active requests is higher that ~6% of ARC size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14516
openzfsonwindows/openzfs#206 found that it is possible to trip
`VERIFY(list_is_empty(&lwb->lwb_itxs))` when a `zil_commit()` is delayed
by the scheduler long enough for a parallel `zil_suspend()` operation to
exit `zil_commit_impl()`. This is a data race. To prevent this, we
introduce a `zilog->zl_suspend_lock` rwlock to ensure that all
outstanding `zil_commit()` operations finish before `zil_suspend()`
begins and that subsequent operations fallback to `txg_wait_synced()`
after `zil_suspend()` has begun.
On `PREEMPT_RT` Linux kernels, the `rw_enter()` implementation suffers
from writer starvation. This means that a ZIL intensive system can delay
`zil_suspend()` indefinitely. This is a pre-existing problem that
affects everything that uses rw locks, so it needs to be addressed in
the SPL. However, builds against `PREEMPT_RT` Linux kernels are
currently broken due to a GPL symbol issue (#11097), so we can safely
disregard that issue for now.
Reported-by: Arun KV <arun.kv@datacore.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14514
A spurious mutex_exit() in a development branch caused weird issues
until I identified it. An assertion prior to mutex_exit() would have
caught it. Rather than adding assertions before invocations of
mutex_exit() in the code, let us simply add an assertion to
mutex_exit(). It is cheap and will likely improve developer
productivity.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Sponsored-By: Wasabi Technology, Inc.
Closes#14541
Commit 34ce4c4 made zfeature_active() non-static. This is not required.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14546
Hole detection in the zio compression code allows us to
opportunistically skip compression on holes. We can go a step further
by not doing memory allocations on holes either.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Sponsored-by: Wasabi Technology, Inc.
Closes#14500
In commit 0a5b942d4 the FreeBSD SECTION_STATIC macro was set to
".rodata". This assembler directive is supported by LLVM (as a
convenience alias for ".section .rodata") by not by GNU as.
This caused the FreeBSD builds that are done with gcc to fail.
Therefore, use ".section .rodata" instead, similar to the other
asm_linkage.h headers.
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Dimitry Andric <dimitry@andric.com>
Closes#14526
When a page is faulted in for memory mapped I/O the page lock
may be dropped before it has been read and marked up to date.
If a buffered read encounters such a page in mappedread() it
must wait until the page has been updated. Failure to do so
will result in a panic on debug builds and incorrect data on
production builds.
The critical part of this change is in mappedread() where pages
which are not up to date are now handled. Additionally, it
includes the following simplifications.
- zfs_getpage() and zfs_fillpage() could be passed an array of
pages. This could be more efficient if it was used but in
practice only a single page was ever provided. These
interfaces were simplified to acknowledge that.
- update_pages() was modified to correctly set the PG_error bit
on a page when it cannot be read by dmu_read().
- Setting PG_error and PG_uptodate was moved to zfs_fillpage()
from zpl_readpage_common(). This is consistent with the
handling in update_pages() and mappedread().
- Minor additional refactoring to comments and variable
declarations to improve readability.
- Add a test case to exercise concurrent buffered, direct,
and mmap IO to the same file.
- Reduce the mmap_sync test case default run time.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13608Closes#14498
Apply zero padding for checksums consistently. The SNPRINTF_BLKPTR
macro was not updated in commit ac7648179c which results in the
`cli_root/zdb/zdb_checksum.ksh` test case reliably failing.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14497
As of the 4.13 kernel filemap_range_has_page() can be used to
check if there is a page mapped in a given file range. When
available this interface should be used which eliminates the
need for the zp->z_is_mapped boolean.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14493
The zio returned from arc_write() in dmu_objset_sync() uses
zio_nowait(). However we may reach the end of dsl_dataset_sync()
which checks if we need to activate features in the filesystem
without knowing if that zio has even run through the ZIO pipeline yet.
In that case we will flag features to be activated in
dsl_dataset_block_born() but dsl_dataset_sync() has already
completed its run and those features will not actually be activated.
Mitigate this by moving the feature activation code in
dsl_dataset_sync_done(). Also add new ASSERTs in
dsl_scan_visitbp() checking if a block contradicts any filesystem
flags.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13816
In https://github.com/openzfs/zfs/pull/14228 the FreeBSD
SECTION_STATIC was set to ".data" instead of ".rodata". This
commit just restores it back to .rodata.
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#14460
zfs_setproctitle_init() is stubbed out on FreeBSD.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Rob Wing <rob.fx907@gmail.com>
Closes#14441
During snapshot deletion ZFS may issue several reads for each deadlist
to merge them into next snapshot's or pool's bpobj. Number of the dead
lists increases with number of snapshots. On HDD pools it may take
significant time during which sync thread is blocked.
This patch introduces prescient prefetch of required blocks for up to
128 deadlists ahead. Tests show reduction of time required to delete
dataset with 720 snapshots with randomly overwritten file on wide HDD
pool from 75-85 to 22-28 seconds.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Issue #14276Closes#14402
Linux 6.2 changes the second argument of the set_acl operation to be a
"struct dentry *" rather than a "struct inode *". The inode* parameter
is still available as dentry->d_inode, so adjust the call to the _impl
function call to dereference and pass that pointer to it.
Also document that the get_acl -> get_inode_acl member name change from
commit 884a693 was an API change also introduced in Linux 6.2.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#14415
The .align directive used to align storage locations is
ambiguous. On some platforms and assemblers it takes a byte count,
on others the argument is interpreted as a shift value. The current
usage expects the first interpretation.
Replace it with the unambiguous .balign directive which always
expects a byte count, regardless of platform and assembler.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#14422
Introduce four new vdev properties:
checksum_n
checksum_t
io_n
io_t
These properties can be used for configuring the thresholds of zed's
diagnosis engine and are interpeted as <N> events in T <seconds>.
When this property is set to a non-default value on a top-level vdev,
those thresholds will also apply to its leaf vdevs. This behavior can be
overridden by explicitly setting the property on the leaf vdev.
Note that, these properties do not persist across vdev replacement. For
this reason, it is advisable to set the property on the top-level vdev
instead of the leaf vdev.
The default values for zed's diagnosis engine (10 events, 600 seconds)
remains unchanged.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Closes#13805
This is only ever used with unsigned data, so the type itself should be
unsigned. Also, PVS Studio's 2016 FreeBSD kernel report correctly
identified the following assertion as always being true, so we can drop
it:
ASSERT3U(dd->dd_space_towrite[i & TXG_MASK], >=, 0);
The reason it was always true is because it would do casts to give us
unsigned comparisons. This could have been fixed by switching to
`ASSERT3S()`, but upon inspection, it turned out that this variable
never should have been allowed to be signed in the first place.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14408
In original code, zfs_znode_dmu_fini is called in zfs_rmnode without
zfs_znode_hold_enter. It seems to assume it's ok to do so when the znode
is unlinked. However this assumption is not correct, as zfs_zget can be
called by NFS through zpl_fh_to_dentry as pointed out by Christian in
https://github.com/openzfs/zfs/pull/12767, which could result in a
use-after-free bug.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12767Closes#14364
Add new macro ASMABI used by Windows to change
calling API to "sysv_abi".
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#14228
This allows parsing of zfs send progress by checking the process
title.
Doing so requires some changes to the send code in libzfs_sendrecv.c;
primarily these changes move some of the accounting around, to allow
for the code to be verbose as normal, or set the process title. Unlike
BSD, setproctitle() isn't standard in Linux; thus, borrowed it from
libbsd with slight modifications.
Authored-by: Sean Eric Fagan <sef@FreeBSD.org>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14376
I recently gained the ability to run Clang's static analyzer on the
linux kernel modules via a few hacks. This extended coverage to code
that was previously missed since Clang's static analyzer only looked at
code that we built in userspace. Running it against the Linux kernel
modules built from my local branch produced a total of 72 reports
against my local branch. Of those, 50 were reports of logic errors and
22 were reports of dead code. Since we already had cleaned up all of
the previous dead code reports, I felt it would be a good next step to
clean up these dead code reports. Clang did a further breakdown of the
dead code reports into:
Dead assignment 15
Dead increment 2
Dead nested assignment 5
The benefit of cleaning these up, especially in the case of dead nested
assignment, is that they can expose places where our error handling is
incorrect. A number of them were fairly straight forward. However
several were not:
In vdev_disk_physio_completion(), not only were we not using the return
value from the static function vdev_disk_dio_put(), but nothing used it,
so I changed it to return void and removed the existing (void) cast in
the other area where we call it in addition to no longer storing it to a
stack value.
In FSE_createDTable(), the function is dead code. Its helper function
FSE_freeDTable() is also dead code, as are the CPP definitions in
`module/zstd/include/zstd_compat_wrapper.h`. We just delete it all.
In zfs_zevent_wait(), we have an optimization opportunity. cv_wait_sig()
returns 0 if there are waiting signals and 1 if there are none. The
Linux SPL version literally returns `signal_pending(current) ? 0 : 1)`
and FreeBSD implements the same semantics, we can just do
`!cv_wait_sig()` in place of `signal_pending(current)` to avoid
unnecessarily calling it again.
zfs_setattr() on FreeBSD version did not have error handling issue
because the code was removed entirely from FreeBSD version. The error is
from updating the attribute directory's files. After some thought, I
decided to propapage errors on it to userspace.
In zfs_secpolicy_tmp_snapshot(), we ignore a lack of permission from the
first check in favor of checking three other permissions. I assume this
is intentional.
In zfs_create_fs(), the return value of zap_update() was not checked
despite setting an important version number. I see no backward
compatibility reason to permit failures, so we add an assertion to catch
failures. Interestingly, Linux is still using ASSERT(error == 0) from
OpenSolaris while FreeBSD has switched to the improved ASSERT0(error)
from illumos, although illumos has yet to adopt it here. ASSERT(error ==
0) was used on Linux while ASSERT0(error) was used on FreeBSD since the
entire file needs conversion and that should be the subject of
another patch.
dnode_move()'s issue was caused by us not having implemented
POINTER_IS_VALID() on Linux. We have a stub in
`include/os/linux/spl/sys/kmem_cache.h` for it, when it really should be
in `include/os/linux/spl/sys/kmem.h` to be consistent with
Illumos/OpenSolaris. FreeBSD put both `POINTER_IS_VALID()` and
`POINTER_INVALIDATE()` in `include/os/freebsd/spl/sys/kmem.h`, so we
copy what it did.
Whenever a report was in platform-specific code, I checked the FreeBSD
version to see if it also applied to FreeBSD, but it was only relevant a
few times.
Lastly, the patch that enabled Clang's static analyzer to be run on the
Linux kernel modules needs more work before it can be put into a PR. I
plan to do that in the future as part of the on-going static analysis
work that I am doing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14380
d_alias may need to be converted to du.d_alias
depending on the kernel version.
d_alias is currently in only one place in the code which
changes
"hlist_for_each_entry(dentry, &inode->i_dentry, d_alias)"
to
"hlist_for_each_entry(dentry, &inode->i_dentry, d_u.d_alias)"
as neccesary.
This effectively results in a double macro expansion
for code that uses the zfs headers but already has its
own macro for just d_alias (lustre in this case).
Remove the conditional code for hlist_for_each_entry
and have a macro for "d_alias -> du.d_alias" instead.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gian-Carlo DeFazio <defazio1@llnl.gov>
Closes#14377
The Blocking Queue (bqueue) code is used by zfs send/receive to send
messages between the various threads. It uses a shared linked list,
which is locked whenever we enqueue or dequeue. For workloads which
process many blocks per second, the locking on the shared list can be
quite expensive.
This commit changes the bqueue logic to have 3 linked lists:
1. An enquing list, which is used only by the (single) enquing thread,
and thus needs no locks.
2. A shared list, with an associated lock.
3. A dequing list, which is used only by the (single) dequing thread,
and thus needs no locks.
The entire enquing list can be moved to the shared list in constant
time, and the entire shared list can be moved to the dequing list in
constant time. These operations only happen when the `fill_fraction` is
reached, or on an explicit flush request. Therefore, the lock only
needs to be acquired infrequently.
The API already allows for dequing to block until an explicit flush, so
callers don't need to be changed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#14121
This commit supports for spare vdev hotplug. The
spare vdev associated with all the pools will be
marked as "Removed" when the drive is physically
detached and will become "Available" when the
drive is reattached. Currently, the spare vdev
status does not change on the drive removal and
the same is the case with reattachment.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14295
Every ARC buffer holds a reference on the header. It means headers with
buffers are never evictable. When we are evicting a header, there can
be no more buffers to free. Just assert that.
b_evict_lock seems not protecting anything now. Remove it.
Buffers checksum should also be freed with the last uncompressed buffer,
so it should not be there also when we are evicting the header.
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
The bi_rw member of struct bio was renamed to bi_opf in Linux 6.2.
As well, Linux's implementation of bio_set_op_attrs(...) has been
removed.
The HAVE_BIO_BI_OPF macro already appears to be defined, but the
removal of the bio_set_op_attrs(...) implementation makes the build
fall back on the locally-defined implementation, which isn't updated
for the bio->bi_opf change. This commit adds that update.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#14324Closes#14331
Linux 6.2 renamed the get_acl() operation to get_inode_acl() in
the inode_operations struct. This should fix Issue #14323.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#14323Closes#14331
On FreeBSD this reduces this structure size from 64 to 56 bytes.
dnode_handle_t respectively reduces from 72 to 64 bytes. It sounds
like a waste to need 72 bytes to be able to relocate 808 bytes of
dnode_t, which relocation on FreeBSD is not even supported.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14317
This saves 40 bytes per full ARC header, reducing it on FreeBSD from
240 to 200 bytes on production bits.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#14315
Previously the primarycache property was handled only in the dbuf
layer. Since the speculative prefetcher is implemented in the ARC,
it had to be disabled for uncacheable buffers.
This change gives the ARC knowledge about uncacheable buffers
via arc_read() and arc_write(). So when remove_reference() drops
the last reference on the ARC header, it can either immediately destroy
it, or if it is marked as prefetch, put it into a new arc_uncached state.
That state is scanned every second, evicting stale buffers that were
not demand read.
This change also tracks dbufs that were read from the beginning,
but not to the end. It is assumed that such buffers may receive further
reads, and so they are stored in dbuf cache. If a following
reads reaches the end of the buffer, it is immediately evicted.
Otherwise it will follow regular dbuf cache eviction. Since the dbuf
layer does not know actual file sizes, this logic is not applied to
the final buffer of a dnode.
Since uncacheable buffers should no longer stay in the ARC for long,
this patch also tries to optimize I/O by allocating ARC physical
buffers as linear to allow buffer sharing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14243
ARC code was many times significantly modified over the years, that
created significant amount of tangled and potentially broken code.
This should make arc_access()/arc_read() code some more readable.
- Decouple prefetch status tracking from b_refcnt. It made sense
originally, but became highly cryptic over the years. Move all the
logic into arc_access(). While there, clean up and comment state
transitions in arc_access(). Some transitions were weird IMO.
- Unify arc_access() calls to arc_read() instead of sometimes calling
it from arc_read_done(). To avoid extra state changes and checks add
one more b_refcnt for ARC_FLAG_IO_IN_PROGRESS.
- Reimplement ARC_FLAG_WAIT in case of ARC_FLAG_IO_IN_PROGRESS with
the same callback mechanism to not falsely account them as hits. Count
those as "iohits", an intermediate between "hits" and "misses". While
there, call read callbacks in original request order, that should be
good for fairness and random speculations/allocations/aggregations.
- Introduce additional statistic counters for prefetch, accounting
predictive vs prescient and hits vs iohits vs misses.
- Remove hash_lock argument from functions not needing it.
- Remove ARC_FLAG_PREDICTIVE_PREFETCH, since it should be opposite
to ARC_FLAG_PRESCIENT_PREFETCH if ARC_FLAG_PREFETCH is set. We may
wish to add ARC_FLAG_PRESCIENT_PREFETCH to few more places.
- Fix few false positive tests found in the process.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14123
There is a lock order inversion deadlock between `spa_errlog_lock` and
`dp_config_rwlock`:
A thread in `spa_delete_dataset_errlog()` is running from a sync task.
It is holding the `dp_config_rwlock` for writer (see
`dsl_sync_task_sync()`), and waiting for the `spa_errlog_lock`.
A thread in `dsl_pool_config_enter()` is holding the `spa_errlog_lock`
(see `spa_get_errlog_size()`) and waiting for the `dp_config_rwlock` (as
reader).
Note that this was introduced by #12812.
This commit address this by defining the lock ordering to be
dp_config_rwlock first, then spa_errlog_lock / spa_errlist_lock.
spa_get_errlog() and spa_get_errlog_size() can acquire the locks in this
order, and then process_error_block() and get_head_and_birth_txg() can
verify that the dp_config_rwlock is already held.
Additionally, a buffer overrun in `spa_get_errlog()` is corrected. Many
code paths didn't check if `*count` got to zero, instead continuing to
overwrite past the beginning of the userspace buffer at `uaddr`.
Tested by having some errors in the pool (via `zinject -t data
/path/to/file`), one thread running `zpool iostat 0.001`, and another
thread runs `zfs destroy` (in a loop, although it hits the first time).
This reproduces the problem easily without the fix, and works with the
fix.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#14239Closes#14289
This adds support to color zfs diff (in the style of git diff)
conditional on the ZFS_COLOR environment variable.
Signed-off-by: Ethan Coe-Renner <coerenner1@llnl.gov>
We currently compute a 64-bit hash three times, which consumes 0.8% CPU
time on ARC eviction heavy workloads. Caching the 64-bit value in the
dbuf allows us to avoid that overhead.
Sponsored-By: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Closes#14251
If the fields to be listed and sorted by are constrained to those
populated by dsl_dataset_fast_stat(), then zfs list is much faster,
as it does not need to open each objset and reads its properties.
A previous optimization by Pawel Dawidek
(0cee24064a) took advantage
of this to make listing snapshot names sorted only by name much faster.
However, it was limited to `-o name -s name`, this work extends this
optimization to work with:
- name
- guid
- createtxg
- numclones
- inconsistent
- redacted
- origin
and could be further extended to any other properties supported by
dsl_dataset_fast_stat() or similar, that do not require extra locking
or reading from disk.
This was committed before (9a9e2e343dfa2af28bf7910de77ae73aa006de62),
but was reverted due to a regression when used with an older kernel.
If the kernel does not populate zc->zc_objset_stats, we now fallback
to getting the properties via the slower interface, to avoid problems
with newer userland and older kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#14110
We do a simple ifdef to avoid calling enable_kernel_spe()/
disable_kernel_spe() on PowerPC.
Reported-by: Rich Ercolani <Rincebrain@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Tested-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14233Closes#14244
There was the series from me a year ago which fixed most of the
callback vs implementation prototype mismatches. It was based on
running the CFI-enabled kernel (in permissive mode -- warning
instead of panic) and performing a full ZTS cycle, and then fixing
all of the problems caught by CFI.
Now, Clang 16-dev has new warning flag, -Wcast-function-type-strict,
which detect such mismatches at compile-time. It allows to find the
remaining issues missed by the first series.
There are only two of them left: one for the
secpolicy_vnode_setattr() callback and one for taskq_dispatch().
The fix is easy, since they are not used anywhere else.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#14207
I've noticed that some of those counters are used in hot paths like
dnode_hold_impl(), and results of this change is visible in profiler.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#14198
It is protected by z_hold_locks, so we do not need more serialization,
simple integer math should be fine.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#14196
Linux defaults to setting "failfast" on BIOs, so that the OS will not
retry IOs that fail, and instead report the error to ZFS.
In some cases, such as errors reported by the HBA driver, not
the device itself, we would wish to retry rather than generating
vdev errors in ZFS. This new property allows that.
This introduces a per vdev option to disable the failfast option.
This also introduces a global module parameter to define the failfast
mask value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Submitted-by: Klara, Inc.
Closes#14056
If there were no zil entries to replay, skip zil_close. zil_close waits
for a transaction to sync. That can take several seconds, for example
during pool import of a resilvering pool. Skipping zil_close can cut
the time for "zpool import" from 2 hours to 45 seconds on a resilvering
pool with a thousand zvols.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Sponsored-by: Axcient
Closes#13999Closes#14015
Linux 5.17 commit torvalds/linux@5dfbfe71e enables "the idmapping
infrastructure to support idmapped mounts of filesystems mounted
with an idmapping". Update the OpenZFS accordingly to improve the
idmapped mount support.
This pull request contains the following changes:
- xattr setter functions are fixed to take mnt_ns argument. Without
this, cp -p would fail for an idmapped mount in a user namespace.
- idmap_util is enhanced/fixed for its use in a user ns context.
- One test case added to test idmapped mount in a user ns.
Reviewed-by: Christian Brauner <christian@brauner.io>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14097
Most of this file was a pile of defines, apparently from Solaris that
controlled nothing in the source tree. A few things controlled the
definition of unused types or macros which I have removed.
Considerable further cleanup is possible including removal of
architectures FreeBSD never supported. This file should likely converge
with the Linux version to the extent possible.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14127
Only DKIOCFLUSHWRITECACHE is required.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14127
Require that ZFS_LEGACY_SUPPORT be defined for legacy ioctl support to
be built. For now, define it in zfs_ioctl_compat.h so support is always
built. This will allow systems that need never support pre-openzfs
tools a mechanism to remove support at build time. This code should
be removed once the need for tool compatability is gone.
No functional change at this time.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14127
vn_renamepath() is a Solaris-ism that was defined away in the FreeBSD
port. Now that the only use is in the FreeBSD zfs_vnops_os.c, drop it
entierly.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14127
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14127
This fixes -Wsingle-bit-bitfield-constant-conversion warning from
clang-16 like:
lib/libzfs/libzfs_dataset.c:4529:19: error: implicit truncation
from 'int' to a one-bit wide bit-field changes value from
1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
flags.nounmount = B_TRUE;
^ ~~~~~~
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14125
uu_avl and uu_list stored internal next/prev pointers and parent
pointers (unused) obfuscated (byte swapped) to hide them from a long
forgotten leak checker (No one at the 2022 OpenZFS developers meeting
could recall the history.) This would break on CHERI systems and adds
no obvious value. Rename the members, use proper types rather than
uintptr_t, and eliminate the related macros.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14126
Avoid assuming than a uint64_t can hold a pointer and reduce the
number of casts in the process.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14131
Avoid assuming that a pointer can fit in a uint64_t and use uintptr_t
instead.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14131
Nothing consumes this definition so stop defining it.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14128
Check __riscv_xlen == 64 rather than _LP64 and define _LP64 if missing.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14128
`snprintf()` is meant to protect against buffer overflows, but operating
on the buffer using its return value, possibly by calling it again, can
cause a buffer overflow, because it will return how many characters it
would have written if it had enough space even when it did not. In a
number of places, we repeatedly call snprintf() by successively
incrementing a buffer offset and decrementing a buffer length, by its
return value. This is a potentially unsafe usage of `snprintf()`
whenever the buffer length is reached. CodeQL complained about this.
To fix this, we introduce `kmem_scnprintf()`, which will return 0 when
the buffer is zero or the number of written characters, minus 1 to
exclude the NULL character, when the buffer was too small. In all other
cases, it behaves like snprintf(). The name is inspired by the Linux and
XNU kernels' `scnprintf()`. The implementation was written before I
thought to look at `scnprintf()` and had a good name for it, but it
turned out to have identical semantics to the Linux kernel version.
That lead to the name, `kmem_scnprintf()`.
CodeQL only catches this issue in loops, so repeated use of snprintf()
outside of a loop was not caught. As a result, a thorough audit of the
codebase was done to examine all instances of `snprintf()` usage for
potential problems and a few were caught. Fixes for them are included in
this patch.
Unfortunately, ZED is one of the places where `snprintf()` is
potentially used incorrectly. Since using `kmem_scnprintf()` in it would
require changing how it is linked, we modify its usage to make it safe,
no matter what buffer length is used. In addition, there was a bug in
the use of the return value where the NULL format character was not
being written by pwrite(). That has been fixed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14098
The previous version reported all the right info, but the VERIFY3 name
made a little more confusing when looking for the matching location in
the source code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Rob N ★ <robn@despairlabs.com>
Closes#14099
Implement support for Linux's RENAME_* flags (for renameat2). Aside from
being quite useful for userspace (providing race-free ways to exchange
paths and implement mv --no-clobber), they are used by overlayfs and are
thus required in order to use overlayfs-on-ZFS.
In order for us to represent the new renameat2(2) flags in the ZIL, we
create two new transaction types for the two flags which need
transactional-level support (RENAME_EXCHANGE and RENAME_WHITEOUT).
RENAME_NOREPLACE does not need any ZIL support because we know that if
the operation succeeded before creating the ZIL entry, there was no file
to be clobbered and thus it can be treated as a regular TX_RENAME.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Snajdr <snajpa@snajpa.net>
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Closes#12209Closes#14070
This is in preparation for RENAME_EXCHANGE and RENAME_WHITEOUT support
for ZoL, but the changes here allow for far nicer fallbacks than the
previous implementation (the source and target are re-linked in case of
the final link failing).
In addition, a small cleanup was done for the "target exists but is a
different type" codepath so that it's more understandable.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Closes#12209Closes#14070
This allows for much cleaner VERIFY-level assertions.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Closes#14070
Open files, which aren't present in the snapshot, which is being
roll-backed to, need to disappear from the visible VFS image of
the dataset.
Kernel provides d_drop function to drop invalid entry from
the dcache, but inode can be referenced by dentry multiple dentries.
The introduced zpl_d_drop_aliases function walks and invalidates
all aliases of an inode.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pavel Snajdr <snajpa@snajpa.net>
Closes#9600Closes#14070
Follow up for 4938d01d which changed zio_flag from enum to uint64_t.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14100
We ran out of space in enum zio_flag for additional flags. Rather than
introduce enum zio_flag2 and then modify a bunch of functions to take a
second flags variable, we expand the type to 64 bits via `typedef
uint64_t zio_flag_t`.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Richard Yao <richard.yao@klarasystems.com>
Closes#14086
vm_object_page_clean() expects that the associated vnode is locked
as VOP_PUTPAGES() may get called on the vnode.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#14079
The use of __noreturn__ in 55d7afa4ad on
spl_panic() caused objtool warnings on Linux when the kernel is built
with CONFIG_STACK_VALIDATION=y. This patch works around that by
restricting the application of __noreturn__ to builds for static
analyzers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14068
Microzap on-disk format does not include a hash tree, expecting one to
be built in RAM during mzap_open(). The built tree is linked to DMU
user buffer, freed when original DMU buffer is dropped from cache. I've
found that workloads accessing many large directories and having active
eviction from DMU cache spend significant amount of time building and
then destroying the trees. I've also found that for each 64 byte mzap
element additional 64 byte tree element is allocated, that is a waste
of memory and CPU caches.
Improve memory efficiency of the hash tree by switching from AVL-tree
to B-tree. It allows to save 24 bytes per element just on pointers.
Save 32 bits on mze_hash by storing only upper 32 bits since lower 32
bits are always zero for microzaps. Save 16 bits on mze_chunkid, since
microzap can never have so many elements. Respectively with the 16 bits
there can be no more than 16 bits of collision differentiators. As
result, struct mzap_ent now drops from 48 (rounded to 64) to 8 bytes.
Tune B-trees for small data. Reduce BTREE_CORE_ELEMS from 128 to 126
to allow struct zfs_btree_core in case of 8 byte elements to pack into
2KB instead of 4KB. Aside of the microzaps it should also help 32bit
range trees. Allow custom B-tree leaf size to reduce memmove() time.
Split zap_name_alloc() into zap_name_alloc() and zap_name_init_str().
It allows to not waste time allocating/freeing memory when processing
multiple names in a loop during mzap_open().
Together on a pool with 10K directories of 1800 files each and DMU
cache limited to 128MB this reduces time of `find . -name zzz` by 41%
from 7.63s to 4.47s, and saves additional ~30% of CPU time on the DMU
cache reclamation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14039
Currently, additional/extra copies are created for metadata in
addition to the redundancy provided by the pool(mirror/raidz/draid),
due to this 2 times more space is utilized per inode and this decreases
the total number of inodes that can be created in the filesystem. By
setting redundant_metadata to none, no additional copies of metadata
are created, hence can reduce the space consumed by the additional
metadata copies and increase the total number of inodes that can be
created in the filesystem. Additionally, this can improve file create
performance due to the reduced amount of metadata which needs
to be written.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#13680
Adds support for idmapped mounts. Supported as of Linux 5.12 this
functionality allows user and group IDs to be remapped without changing
their state on disk. This can be useful for portable home directories
and a variety of container related use cases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#12923Closes#13671
Various module parameters such as `zfs_arc_max` were originally
`uint64_t` on OpenSolaris/Illumos, but were changed to `unsigned long`
for Linux compatibility because Linux's kernel default module parameter
implementation did not support 64-bit types on 32-bit platforms. This
caused problems when porting OpenZFS to Windows because its LLP64 memory
model made `unsigned long` a 32-bit type on 64-bit, which created the
undesireable situation that parameters that should accept 64-bit values
could not on 64-bit Windows.
Upon inspection, it turns out that the Linux kernel module parameter
interface is extensible, such that we are allowed to define our own
types. Rather than maintaining the original type change via hacks to to
continue shrinking module parameters on 32-bit Linux, we implement
support for 64-bit module parameters on Linux.
After doing a review of all 64-bit kernel parameters (found via the man
page and also proposed changes by Andrew Innes), the kernel module
parameters fell into a few groups:
Parameters that were originally 64-bit on Illumos:
* dbuf_cache_max_bytes
* dbuf_metadata_cache_max_bytes
* l2arc_feed_min_ms
* l2arc_feed_secs
* l2arc_headroom
* l2arc_headroom_boost
* l2arc_write_boost
* l2arc_write_max
* metaslab_aliquot
* metaslab_force_ganging
* zfetch_array_rd_sz
* zfs_arc_max
* zfs_arc_meta_limit
* zfs_arc_meta_min
* zfs_arc_min
* zfs_async_block_max_blocks
* zfs_condense_max_obsolete_bytes
* zfs_condense_min_mapping_bytes
* zfs_deadman_checktime_ms
* zfs_deadman_synctime_ms
* zfs_initialize_chunk_size
* zfs_initialize_value
* zfs_lua_max_instrlimit
* zfs_lua_max_memlimit
* zil_slog_bulk
Parameters that were originally 32-bit on Illumos:
* zfs_per_txg_dirty_frees_percent
Parameters that were originally `ssize_t` on Illumos:
* zfs_immediate_write_sz
Note that `ssize_t` is `int32_t` on 32-bit and `int64_t` on 64-bit. It
has been upgraded to 64-bit.
Parameters that were `long`/`unsigned long` because of Linux/FreeBSD
influence:
* l2arc_rebuild_blocks_min_l2size
* zfs_key_max_salt_uses
* zfs_max_log_walking
* zfs_max_logsm_summary_length
* zfs_metaslab_max_size_cache_sec
* zfs_min_metaslabs_to_flush
* zfs_multihost_interval
* zfs_unflushed_log_block_max
* zfs_unflushed_log_block_min
* zfs_unflushed_log_block_pct
* zfs_unflushed_max_mem_amt
* zfs_unflushed_max_mem_ppm
New parameters that do not exist in Illumos:
* l2arc_trim_ahead
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_arc_sys_free
* zfs_deadman_ziotime_ms
* zfs_delete_blocks
* zfs_history_output_max
* zfs_livelist_max_entries
* zfs_max_async_dedup_frees
* zfs_max_nvlist_src_size
* zfs_rebuild_max_segment
* zfs_rebuild_vdev_limit
* zfs_unflushed_log_txg_max
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
* zfs_vnops_read_chunk_size
* zvol_max_discard_blocks
Rather than clutter the lists with commentary, the module parameters
that need comments are repeated below.
A few parameters were defined in Linux/FreeBSD specific code, where the
use of ulong/long is not an issue for portability, so we leave them
alone:
* zfs_delete_blocks
* zfs_key_max_salt_uses
* zvol_max_discard_blocks
The documentation for a few parameters was found to be incorrect:
* zfs_deadman_checktime_ms - incorrectly documented as int
* zfs_delete_blocks - not documented as Linux only
* zfs_history_output_max - incorrectly documented as int
* zfs_vnops_read_chunk_size - incorrectly documented as long
* zvol_max_discard_blocks - incorrectly documented as ulong
The documentation for these has been fixed, alongside the changes to
document the switch to fixed width types.
In addition, several kernel module parameters were percentages or held
ashift values, so being 64-bit never made sense for them. They have been
downgraded to 32-bit:
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_per_txg_dirty_frees_percent
* zfs_unflushed_log_block_pct
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
Of special note are `zfs_vdev_max_auto_ashift` and
`zfs_vdev_min_auto_ashift`, which were already defined as `uint64_t`,
and passed to the kernel as `ulong`. This is inherently buggy on big
endian 32-bit Linux, since the values would not be written to the
correct locations. 32-bit FreeBSD was unaffected because its sysctl code
correctly treated this as a `uint64_t`.
Lastly, a code comment suggests that `zfs_arc_sys_free` is
Linux-specific, but there is nothing to indicate to me that it is
Linux-specific. Nothing was done about that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Original-patch-by: Andrew Innes <andrew.c12@gmail.com>
Original-patch-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13984Closes#14004
On older kernels, the definition for `module_param_call()` typecasts
function pointers to `(void *)`, which triggers -Werror, causing the
check to return false when it should return true.
Fixing this breaks the build process on some older kernels because they
define a `__check_old_set_param()` function in their headers that checks
for a non-constified `->set()`. We workaround that through the c
preprocessor by defining `__check_old_set_param(set)` to `(set)`, which
prevents the build failures.
However, it is now apparent that all kernels that we support have
adopted the GRSecurity change, so there is no need to have an explicit
autotools check for it anymore. We therefore remove the autotools check,
while adding the workaround to our headers for the build time
non-constified `->set()` check done by older kernel headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13984Closes#14004
In libzutil, for zpool_search_import and zpool_find_config, we use
libpc_handle_t internally, which does not maintain error code and it is
not exposed in the interface. Due to this, the error information is not
propagated to the caller. Instead, an error message is printed on
stderr.
This commit adds lpc_error field in libpc_handle_t and exposes it in
the interface, which can be used by the users of libzutil to get the
appropriate error information and handle it accordingly.
Users of the API can also control if they want to print the error
message on stderr.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13969
Some header files define structures like this one:
typedef const struct zio_checksum_info {
/* ... */
const char *ci_name;
} zio_abd_checksum_func_t;
So we can use `zio_abd_checksum_func_t` for const declarations now.
It's not needed that we use the `const` qualifier again like this:
`const zio_abd_checksum_func_t *varname;`
This patch solves the double const qualifiers, which were found by
smatch.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13961
Both Clang's Static Analyzer and Synopsys' Coverity would ignore
assertions. Following Clang's advice, we annotate our assertions:
https://clang-analyzer.llvm.org/annotations.html#custom_assertions
This makes both Clang's Static Analyzer and Coverity properly identify
assertions. This change reduced Clang's reported defects from 246 to
180. It also reduced the false positives reported by Coverityi by 10,
while enabling Coverity to find 9 more defects that previously were
false negatives.
A couple examples of this would be CID-1524417 and CID-1524423. After
submitting a build to coverity with the modified assertions, CID-1524417
disappeared while the report for CID-1524423 no longer claimed that the
assertion tripped.
Coincidentally, it turns out that it is possible to more accurately
annotate our headers than the Coverity modelling file permits in the
case of format strings. Since we can do that and this patch annotates
headers whenever `__coverity_panic__()` would have been used in the
model file, we drop all models that use `__coverity_panic__()` from the
model file.
Upon seeing the success in eliminating false positives involving
assertions, it occurred to me that we could also modify our headers to
eliminate coverity's false positives involving byte swaps. We now have
coverity specific byteswap macros, that do nothing, to disable
Coverity's false positives when we do byte swaps. This allowed us to
also drop the byteswap definitions from the model file.
Lastly, a model file update has been done beyond the mentioned
deletions:
* The definitions of `umem_alloc_aligned()`, `umem_alloc()` andi
`umem_zalloc()` were originally implemented in a way that was
intended to inform coverity that when KM_SLEEP has been passed these
functions, they do not return NULL. A small error in how this was
done was found, so we correct it.
* Definitions for umem_cache_alloc() and umem_cache_free() have been
added.
In practice, no false positives were avoided by making these changes,
but in the interest of correctness from future coverity builds, we make
them anyway.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13902
ZED does not take any action for disk removal events if there is no
spare VDEV available. Added zpool_vdev_remove_wanted() in libzfs
and vdev_remove_wanted() in vdev.c to remove the VDEV through ZED
on removal event. This means that if you are running zed and
remove a disk, it will be properly marked as REMOVED.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13797
Bit 28 is used by an internal Nutanix feature which might be
upstreamed in the future.
Bit 29 is the last unused bit. It is reserved to indicate a
to-be-designed extension to the stream format which will accomodate
more feature flags.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Issue #13795Closes#13796
Commit 985c33b132 added DMU_BACKUP_FEATURE_BLAKE3 but it is not used by
the code.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Issue #13795Closes#13796
In #13871, zfs_vdev_aggregation_limit_non_rotating and
zfs_vdev_aggregation_limit being signed was pointed out as a possible
reason not to eliminate an unnecessary MAX(unsigned, 0) since the
unsigned value was assigned from them.
There is no reason for these module parameters to be signed and upon
inspection, it was found that there are a number of other module
parameters that are signed, but should not be, so we make them unsigned.
Making them unsigned made it clear that some other variables in the code
should also be unsigned, so we also make those unsigned. This prevents
users from setting negative values that could potentially cause bad
behaviors. It also makes the code slightly easier to understand.
Mostly module parameters that deal with timeouts, limits, bitshifts and
percentages are made unsigned by this. Any that are boolean are left
signed, since whether booleans should be considered signed or unsigned
does not matter.
Making zfs_arc_lotsfree_percent unsigned caused a
`zfs_arc_lotsfree_percent >= 0` check to become redundant, so it was
removed. Removing the check was also necessary to prevent a compiler
error from -Werror=type-limits.
Several end of line comments had to be moved to their own lines because
replacing int with uint_t caused us to exceed the 80 character limit
enforced by cstyle.pl.
The following were kept signed because they are passed to
taskq_create(), which expects signed values and modifying the
OpenSolaris/Illumos DDI is out of scope of this patch:
* metaslab_load_pct
* zfs_sync_taskq_batch_pct
* zfs_zil_clean_taskq_nthr_pct
* zfs_zil_clean_taskq_minalloc
* zfs_zil_clean_taskq_maxalloc
* zfs_arc_prune_task_threads
Also, negative values in those parameters was found to be harmless.
The following were left signed because either negative values make
sense, or more analysis was needed to determine whether negative values
should be disallowed:
* zfs_metaslab_switch_threshold
* zfs_pd_bytes_max
* zfs_livelist_min_percent_shared
zfs_multihost_history was made static to be consistent with other
parameters.
A number of module parameters were marked as signed, but in reality
referenced unsigned variables. upgrade_errlog_limit is one of the
numerous examples. In the case of zfs_vdev_async_read_max_active, it was
already uint32_t, but zdb had an extern int declaration for it.
Interestingly, the documentation in zfs.4 was right for
upgrade_errlog_limit despite the module parameter being wrongly marked,
while the documentation for zfs_vdev_async_read_max_active (and friends)
was wrong. It was also wrong for zstd_abort_size, which was unsigned,
but was documented as signed.
Also, the documentation in zfs.4 incorrectly described the following
parameters as ulong when they were int:
* zfs_arc_meta_adjust_restarts
* zfs_override_estimate_recordsize
They are now uint_t as of this patch and thus the man page has been
updated to describe them as uint.
dbuf_state_index was left alone since it does nothing and perhaps should
be removed in another patch.
If any module parameters were missed, they were not found by `grep -r
'ZFS_MODULE_PARAM' | grep ', INT'`. I did find a few that grep missed,
but only because they were in files that had hits.
This patch intentionally did not attempt to address whether some of
these module parameters should be elevated to 64-bit parameters, because
the length of a long on 32-bit is 32-bit.
Lastly, it was pointed out during review that uint_t is a better match
for these variables than uint32_t because FreeBSD kernel parameter
definitions are designed for uint_t, whose bit width can change in
future memory models. As a result, we change the existing parameters
that are uint32_t to use uint_t.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13875
Coverity found a bug in `zfs_secpolicy_create_clone()` where it is
possible for us to pass an unterminated string when `zfs_get_parent()`
returns an error. Upon inspection, it is clear that using `strlcpy()`
would have avoided this issue.
Looking at the codebase, there are a number of other uses of `strncpy()`
that are unsafe and even when it is used safely, switching to
`strlcpy()` would make the code more readable. Therefore, we switch all
instances where we use `strncpy()` to use `strlcpy()`.
Unfortunately, we do not portably have access to `strlcpy()` in
tests/zfs-tests/cmd/zfs_diff-socket.c because it does not link to
libspl. Modifying the appropriate Makefile.am to try to link to it
resulted in an error from the naming choice used in the file. Trying to
disable the check on the file did not work on FreeBSD because Clang
ignores `#undef` when a definition is provided by `-Dstrncpy(...)=...`.
We workaround that by explictly including the C file from libspl into
the test. This makes things build correctly everywhere.
We add a deprecation warning to `config/Rules.am` and suppress it on the
remaining `strncpy()` usage. `strlcpy()` is not portably avaliable in
tests/zfs-tests/cmd/zfs_diff-socket.c, so we use `snprintf()` there as a
substitute.
This patch does not tackle the related problem of `strcpy()`, which is
even less safe. Thankfully, a quick inspection found that it is used far
more correctly than strncpy() was used. A quick inspection did not find
any problems with `strcpy()` usage outside of zhack, but it should be
said that I only checked around 90% of them.
Lastly, some of the fields in kstat_t varied in size by 1 depending on
whether they were in userspace or in the kernel. The origin of this
discrepancy appears to be 04a479f706 where
it was made for no apparent reason. It conflicts with the comment on
KSTAT_STRLEN, so we shrink the kernel field sizes to match the userspace
field sizes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13876
When receiving full/newfs on existing dataset, then it should be done
with "-F" flag. Its enforced for initial receive in checks done in
zfs_receive_one function of libzfs. Similarly, on resuming full/newfs
recv on existing dataset, it should be done with "-F" flag.
When dataset doesn't exist, then full/new recv is done on newly created
dataset and it's marked INCONSISTENT. But when receiving on existing
dataset, recv is first done on %recv and its marked INCONSISTENT.
Existing dataset is not marked INCONSISTENT. Resume of full/newfs
receive with dataset not INCONSISTENT indicates that its resuming newfs
on existing dataset. So, enforce "-F" flag in this case.
Also return an error from dmu_recv_resume_begin_check() in zfs kernel,
when its resuming full/newfs recv without force.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chunwei Chen <david.chen@nutanix.com>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#13856Closes#13857
The extern declaration is only for Linux, move this line
into the right #ifdef section.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Martin Matuska <mm@FreeBSD.org>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13934Closes#13936
Incorrectly sizing the array of hash locks used to protect the
dbuf hash table can lead to contention and reduce performance.
We could unconditionally allocate a larger array for the locks
but it's wasteful, particularly for a low-memory system.
Instead, dynamically allocate the array of locks and scale
it based on total system memory.
Additionally, add a new `dbuf_mutex_cache_shift` module option
which can be used to override the hash lock array size. This is
disabled by default (dbuf_mutex_hash_shift=0) and can only be
set at module load time. The minimum target array size is set
to 8192, this matches the current constant value.
Note that the count of the dbuf hash table and count of the
mutex array were added to the /proc/spl/kstat/zfs/dbufstats
kstat.
Finally, this change removes the _KERNEL conditional checks.
These were not required since for the user space build there
is no difference between the kmem and vmem interfaces.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13928
This reverts commit 34dbc618f5. While this
change resolved the lock contention observed for certain workloads, it
inadventantly reduced the maximum hash inserts/removes per second. This
appears to be due to the slightly higher acquisition cost of a rwlock vs
a mutex.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
There were never any users and it so happens the operation is not even
supported by rrm locks -- the macros were wrong for Linux and FreeBSD
when not using it's RMS locks.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#13906
Provides the missing full barrier variant to the membar primitive set.
While not used right now, this is probably going to change down the
road.
Name taken from Solaris, to follow the existing routines.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#13907
The FreeBSD project's coverity scans found dead code in `zfs_readdir()`.
Also, the comment above `zfs_readdir()` is out of date.
I fixed the comment and deleted all of the dead code, plus additional
dead code that was found upon review.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13924
Coverity caught a possible NULL pointer dereference in dead code. We can
delete it all.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chunwei Chen <david.chen@nutanix.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13900
param_set_arc_free_target(SYSCTL_HANDLER_ARGS) and
param_set_arc_no_grow_shift(SYSCTL_HANDLER_ARGS) defined in
sysctl_os.c must be made available to arc_os.c.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#13915
Add needed cpu feature tests for powerpc architecture.
Overview:
zfs_altivec_available() - needed by RAID-Z
zfs_vsx_available() - needed by BLAKE3
zfs_isa207_available() - needed by SHA2
Part 1 - Userspace
- use getauxval() for Linux and elf_aux_info() for FreeBSD
- direct including <sys/auxv.h> fails with double definitions
- so we self define the needed functions and definitions
Part 2 - Kernel space FreeBSD
- use exported cpu_features of <powerpc/cpu.h>
Part 3 - Kernel space Linux
- use cpu_has_feature() function of <asm/cpufeature.h>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13725
Apply similar options to BLAKE3 as it is done for zfs_fletcher_4_impl.
The zfs module parameter on Linux changes from icp_blake3_impl to
zfs_blake3_impl.
You can check and set it on Linux via sysfs like this:
```
[bash]# cat /sys/module/zfs/parameters/zfs_blake3_impl
cycle [fastest] generic sse2 sse41 avx2
[bash]# echo sse2 > /sys/module/zfs/parameters/zfs_blake3_impl
[bash]# cat /sys/module/zfs/parameters/zfs_blake3_impl
cycle fastest generic [sse2] sse41 avx2
```
The modprobe module parameters may also be used now:
```
[bash]# modprobe zfs zfs_blake3_impl=sse41
[bash]# cat /sys/module/zfs/parameters/zfs_blake3_impl
cycle fastest generic sse2 [sse41] avx2
```
On FreeBSD the BLAKE3 implementation can be set via sysctl like this:
```
[bsd]# sysctl vfs.zfs.blake3_impl
vfs.zfs.blake3_impl: cycle [fastest] generic sse2 sse41 avx2
[bsd]# sysctl vfs.zfs.blake3_impl=sse2
vfs.zfs.blake3_impl: cycle [fastest] generic sse2 sse41 avx2 \
-> cycle fastest generic [sse2] sse41 avx2
```
This commit changes also some Blake3 internals like these:
- blake3_impl_ops_t was renamed to blake3_ops_t
- all functions are named blake3_impl_NAME() now
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13725
Add a meaningful error message for ECKSUM to common error messages.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#6805Closes#13808Closes#13898
- Some optimizations for bqueue enqueue/dequeue.
- Added a fix to prevent deadlock when both bqueue_enqueue_impl()
and bqueue_dequeue() waits for signal to be triggered.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13855
Replace ZFS_ENTER and ZFS_VERIFY_ZP, which have hidden returns, with
functions that return error code. The reason we want to do this is
because hidden returns are not obvious and had caused some missing fail
path unwinding.
This patch changes the common, linux, and freebsd parts. Also fixes
fail path unwinding in zfs_fsync, zpl_fsync, zpl_xattr_{list,get,set}, and
zfs_lookup().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#13831
We inherited membar_consumer() and membar_producer() from OpenSolaris,
but we had replaced membar_consumer() with Linux's smp_rmb() in
zfs_ioctl.c. The FreeBSD SPL consequently implemented a shim for the
Linux-only smp_rmb().
We reinstate membar_consumer() in platform independent code and fix the
FreeBSD SPL to implement membar_consumer() in a way analogous to Linux.
Reviewed-by: Konstantin Belousov <kib@FreeBSD.org>
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13843
Unused code detected by coverity.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13868
In our codebase, `cond_resched() and `schedule()` are Linux kernel
functions that have replaced the OpenSolaris `kpreempt()` functions in
the codebase to such an extent that `kpreempt()` in zfs_context.h was
broken. Nobody noticed because we did not actually use it. The header
had defined `kpreempt()` as `yield()`, which works on OpenSolaris and
Illumos where `sched_yield()` is a wrapper for `yield()`, but that does
not work on any other platform.
The FreeBSD platform specific code implemented shims for these, but the
shim for `schedule()` forced us to wait, which is different than merely
rescheduling to another thread as the original Linux code does, while
the shim for `cond_resched()` had the same definition as its kernel
kpreempt() shim.
After studying this, I have concluded that we should reintroduce the
kpreempt() function in platform independent code with the following
definitions:
- In the Linux kernel:
kpreempt(unused) -> cond_resched()
- In the FreeBSD kernel:
kpreempt(unused) -> kern_yield(PRI_USER)
- In userspace:
kpreempt(unused) -> sched_yield()
In userspace, nothing changes from this cleanup. In the kernels, the
function `fm_fini()` will now call `kern_yield(PRI_USER)` on FreeBSD and
`cond_resched()` on Linux. This is instead of `pause("schedule", 1)` on
FreeBSD and `schedule()` on Linux. This makes our behavior consistent
across platforms.
Note that Linux's SPL continues to use `cond_resched()` and
`schedule()`. However, those functions have been removed from both the
FreeBSD code and userspace code.
This should have the benefit of making it slightly easier to port the
code to new platforms by making how things should be mapped less
confusing.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13845
The are a few cases where stale entries in /etc/exports.d/zfs.exports
will cause the nfs-server service to fail when starting up.
Since the nfs-server startup consumes /etc/exports.d/zfs.exports, the
zfs-share service (which rebuilds the list of zfs exports) should run
before the nfs-server service.
To make the zfs-share service resilient to stale exports, this change
truncates the zfs config file as part of the zfs share -a operation.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#13775
Users were seeing floods of `config_sync` events when autoexpand was
enabled. This happened because all "disk status change" udev events
invoke the autoexpand codepath, which calls zpool_relabel_disk(),
which in turn cause another "disk status change" event to happen,
in a feedback loop. Note that "disk status change" happens every time
a user calls close() on a block device.
This commit breaks the feedback loop by only allowing an autoexpand
to happen if the disk actually changed size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes: #7132Closes: #7366Closes#13729
When iterating through children physical ashifts for vdev, prefer
ones above the maximum logical ashift, that we can actually use,
but within the administrator defined maximum.
When selecting top-level vdev ashift, do not set it to the defined
maximum in case physical ashift is even higher, but just ignore one.
Using the maximum does not prevent misaligned writes, but reduces
space efficiency. Since ZFS tries to write data sequentially and
aggregates the writes, in many cases large misanigned writes may be
not as bad as the space penalty otherwise.
Allow internal physical ashifts for vdevs higher than SHIFT_MAX.
May be one day allocator or aggregation could benefit from that.
Reduce zfs_vdev_max_auto_ashift default from 16 (64KB) to 14 (16KB),
so that ZFS may still use bigger ashifts up to SHIFT_MAX (64KB),
but only if it really has to or explicitly told to, but not as an
"optimization".
There are some read-intensive NVMe SSDs that report Preferred Write
Alignment of 64KB, and attempt to build RAIDZ2 of those leads to a
space inefficiency that can't be justified. Instead these changes
make ZFS fall back to logical ashift of 12 (4KB) by default and
only warn user that it may be suboptimal for performance.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#13798
Without this patch, the
ASSERT3U(dbuf_is_metadata(db), ==, arc_is_metadata(buf));
at the beginning of dbuf_assign_arcbuf can panic
if the object type is a DMU_OT_NEWTYPE that has
DMU_OT_METADATA set.
While we're at it, fix DMU_OT_IS_ENCRYPTED as well.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#13842
Some ARM BSPs run the Android kernel, which has
a modified xattr_handler->get() function signature.
This adds support to compile against these kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Walter Huf <hufman@gmail.com>
Closes#13824
This will be used to implement kqfilter support for zvol cdevs.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rob Wing <rew@FreeBSD.org>
Closes#13773
This commit adds DD_FIELD string used in extensified dsl_dir zap object
for snapshots_changed property.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13819
Only the single snapshot rename is provided.
The recursive or more complex rename can be scripted.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#13802
FreeBSD had a few platform-specific ARC tunables in the wrong place:
- Move FreeBSD-specifc ARC tunables into the same vfs.zfs.arc node as
the rest of the ARC tunables.
- Move the handlers from arc_os.c to sysctl_os.c and add compat sysctls
for the legacy names.
While here, some additional clean up:
- Most handlers are specific to a particular variable and don't need a
pointer passed through the args.
- Group blocks of related variables, handlers, and sysctl declarations
into logical sections.
- Match variable types for temporaries in handlers with the type of the
global variable.
- Remove leftover comments.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13756
ZFS_MODULE_PARAM_CALL handlers implement their own locking if needed
and do not require Giant.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13756
The vfs_*_feature() macros turn anything that uses them into dead code,
so we can delete all of it.
As a side effect, zfs_set_fuid_feature() is now identical in
module/os/freebsd/zfs/zfs_vnops_os.c and
module/os/linux/zfs/zfs_vnops_os.c. A few other functions are identical
too. Future cleanup could move these into a common file.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13832
This reverts commit 80a650b7bb. This change
inadvertently introduced a regression in ztest where one of the new ASSERTs
is triggered in dsl_scan_visitbp().
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #12275Closes#13799
When scrubbing an encrypted filesystem with unloaded key still report an
error in zpool status.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@axcient.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13675Closes#13717
The 6.0 kernel added a printf-style var-arg for args > 0 to the
register_shrinker function, in order to add names to shrinkers, in
commit e33c267ab70de4249d22d7eab1cc7d68a889bac2. This enables the
shrinkers to have friendly names exposed in /sys/kernel/debug/shrinker/.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#13748
This is an oddly specific function that has never had any consumers in
the history of this repo. Get rid of it and the pile of helper
functions that exist for it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13724
Make dd_snap_cmtime property persistent across mount and unmount
operations by storing in ZAP and restore the value from ZAP on hold
into dd_snap_cmtime instead of updating it.
Expose dd_snap_cmtime as 'snapshots_changed' property that provides a
mechanism to quickly determine whether snapshot list for dataset has
changed without having to mount a dataset or iterate the snapshot list.
It specifies the time at which a snapshot for a dataset was last
created or deleted. This allows us to be more efficient how often we
query snapshots.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13635
This type of recv is used to heal corrupted data when a replica
of the data already exists (in the form of a send file for example).
With the provided send stream, corrective receive will read from
disk blocks described by the WRITE records. When any of the reads
come back with ECKSUM we use the data from the corresponding WRITE
record to rewrite the corrupted block.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Alek Pinchuk <apinchuk@axcient.com>
Closes#9372
ZIL kstats are reported in an inclusive way, i.e., same counters are
shared to capture all the activities happening in zil. Added support
to report zil stats for every datset individually by combining them
with already exposed dataset kstats.
Wmsum uses per cpu counters and provide less overhead as compared
to atomic operations. Updated zil kstats to replace wmsum counters
to avoid atomic operations.
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13636
It may happen that scan bookmark points to a block that was turned
into a part of a big hole. In such case dsl_scan_visitbp() may skip
it and dsl_scan_check_resume() will not be called for it. As result
new scan suspend won't be possible until the end of the object, that
may take hours if the object is a multi-terabyte ZVOL on a slow HDD
pool, stretching TXG to all that time, creating all sorts of problems.
This patch changes the resume condition to any greater or equal block,
so even if we miss the bookmarked block, the next one we find will
delete the bookmark, allowing new suspend.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13643
Makes the case sensitivity setting visible on Linux in /proc/mounts.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13607
If NEED_SOLARIS_BOOLEAN is defined we define an enum boolean_t, which
defines B_TRUE/B_FALSE as well. If we have both the define and the enum
things don't build (because that translates to
'enum { 0, 1 } boolean_t').
While here also remove an incorrect '#else'. With it in place we only
parse a section if the include guard is triggered. So we'd only use that
code if this file is included twice. This is clearly unintended, and
also means we don't get the 'boolean_t' definition. Fix this.
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Kristof Provost <kprovost@netgate.com>
Sponsored-By: Rubicon Communications, LLC ("Netgate")
Closes#13596
Block statistics calculation during scrub I/O issue in case of sorted
scrub accounted ditto blocks several times. Embedded blocks on other
side were not accounted at all. This change moves the accounting from
issue to scan stage, that fixes both problems and also allows to avoid
pool-wide locking and the lock contention it created.
Since this statistics is quite specific and is not even exposed now
anywhere, disable its calculation by default to not waste CPU time.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13579
Restructure the code in zfs_log_xvattr() to use a lr_attr_end
structure when accessing lr_attr_t elements located after the
variable sized array. This makes the code more understandable
and resolves the accessing beyond the end of the field warnings.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
The current codebase does not support raw sending buffers with block
size > 128kB when large_blocks is not active. This can happen in the
codepath dsl_dataset_sync()->dmu_objset_sync()->zio_nowait() which
calls back dmu_objset_write_done()->dsl_dataset_block_born(). If
dsl_dataset_sync() completes its run before dsl_dataset_block_born() is
called, we will end up not activating some of the necessary flags, while
having blocks based on those flags written in the filesystem. A
subsequent send will then panic.
Fix this by directly deciding in dmu_objset_sync() whether these flags
need to be activated later by dsl_dataset_sync(). Instead of panicking
due to a NULL pointer dereference in dmu_dump_write() in case of a send,
print out an error message. Also during scrub verify there are no
contradicting filesystem flags.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12275Closes#12438
- Introduce first element offset within a leaf. It allows to reduce
by ~50% average memmove() size when adding/removing elements. If the
added/removed element is in the first half of the leaf, we may shift
elements before it and adjust the bth_first instead of moving more
elements after it.
- Use memcpy() instead of memmove() when we know there is no overlap.
- Switch from uint64_t to uint32_t. It does not limit anything,
but 32-bit arches should appreciate it greatly in hot paths.
- Store leaf capacity in struct btree to avoid 64-bit divisions.
- Adjust zfs_btree_insert_into_leaf() to always result in balanced
leaves after splitting, no matter where the new element was inserted.
Not that we care about it much, but it should also allow B-trees with
as little as two elements per leaf instead of 4 previously.
When scrubbing pool of 12 SSDs, storing 1.5TB of 4KB zvol blocks this
reduces amount of time spent in memmove() inside the scan thread from
13.7% to 5.7% and total scrub time by ~15 seconds out of 9 minutes.
It should also reduce spacemaps load time, but I haven't measured it.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13582
- Reduce size and comparison complexity of q_exts_by_size B-tree.
Previous code used two 64-bit divisions and many other operations to
compare two B-tree elements. It created enormous overhead. This
implementation moves the math to the upper level and stores the score
in the B-tree elements themselves. Since all that we need to store in
that B-tree is the extent score and offset, those can fit into single
8 byte value instead of 24 bytes of q_exts_by_addr element and can be
compared with single operation.
- Better decouple secondary tree logic from main range_tree by moving
rt_btree_ops and related functions into dsl_scan.c as ext_size_ops.
Those functions are very small to worry about the code duplication and
range_tree does not need to know details such as rt_btree_compare.
- Instead of accounting number of pending bytes per pool, that needs
atomic on global variable per block, account the number of non-empty
per-vdev queues, that change much more rarely.
- When extent scan is interrupted by TXG end, continue it in the next
TXG instead of selecting next best extent. It allows to avoid leaving
one truncated (and so likely not the best any more) extent each TXG.
On top of some other optimizations this saves about 1.5 minutes out of
10 to scrub pool of 12 SSDs, storing 1.5TB of 4KB zvol blocks.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13576
The kmem_alloc(sizeof (*ctx), KM_NOSLEEP) call on FreeBSD can't be
used in this code segment. Work around this by pre-allocating a percpu
context array for later use.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13568
When building modules (as well as the kernel) with ARCH=um, the options
-Dsetjmp=kernel_setjmp and -Dlongjmp=kernel_longjmp are passed to the C
preprocessor for C files. This causes the setjmp and longjmp used in
module/lua/ldo.c to be kernel_setjmp and kernel_longjmp respectively in
the object file. However, the setjmp and longjmp that is intended to be
called is defined in an architecture dependent assembly file under the
directory module/lua/setjmp. Since it is an assembly and not a C file,
the preprocessor define is not given and the names do not change. This
becomes an issue when modpost is trying to create the Module.symvers
and sees no defined symbol for kernel_setjmp and kernel_longjmp. To fix
this, if the macro CONFIG_UML is defined, then setjmp and longjmp
macros are undefined.
When building with ARCH=um for x86 sub-architectures, CONFIG_X86 is not
defined. Instead, CONFIG_UML_X86 is defined. Despite this, the UML x86
sub-architecture can use the same object files as the x86 architectures
because the x86 sub-architecture UML kernel is running with the same
instruction set as CONFIG_X86. So the modules/Kbuild build file is
updated to add the same object files that CONFIG_X86 would add when
CONFIG_UML_X86 is defined.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Glenn Washburn <development@efficientek.com>
Closes#13547
This allows ZFS datasets to be delegated to a user/mount namespace
Within that namespace, only the delegated datasets are visible
Works very similarly to Zones/Jailes on other ZFS OSes
As a user:
```
$ unshare -Um
$ zfs list
no datasets available
$ echo $$
1234
```
As root:
```
# zfs list
NAME ZONED MOUNTPOINT
containers off /containers
containers/host off /containers/host
containers/host/child off /containers/host/child
containers/host/child/gchild off /containers/host/child/gchild
containers/unpriv on /unpriv
containers/unpriv/child on /unpriv/child
containers/unpriv/child/gchild on /unpriv/child/gchild
# zfs zone /proc/1234/ns/user containers/unpriv
```
Back to the user namespace:
```
$ zfs list
NAME USED AVAIL REFER MOUNTPOINT
containers 129M 47.8G 24K /containers
containers/unpriv 128M 47.8G 24K /unpriv
containers/unpriv/child 128M 47.8G 128M /unpriv/child
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will.andrews@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Buddy <https://buddy.works>
Closes#12263
When read and writing the UID/GID, we always want the value
relative to the root user namespace, the kernel will take care
of remapping this to the user namespace for us.
Calling from_kuid(user_ns, uid) with a unmapped uid will return -1
as that uid is outside of the scope of that namespace, and will result
in the files inside the namespace all being owned by 'nobody' and not
being allowed to call chmod or chown on them.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#12263
Add support for the kernel's block multiqueue (blk-mq) interface in
the zvol block driver. blk-mq creates multiple request queues on
different CPUs rather than having a single request queue. This can
improve zvol performance with multithreaded reads/writes.
This implementation uses the blk-mq interfaces on 4.13 or newer
kernels. Building against older kernels will fall back to the
older BIO interfaces.
Note that you must set the `zvol_use_blk_mq` module param to
enable the blk-mq API. It is disabled by default.
In addition, this commit lets the zvol blk-mq layer process whole
`struct request` IOs at a time, rather than breaking them down
into their individual BIOs. This reduces dbuf lock contention
and overhead versus the legacy zvol submit_bio() codepath.
sequential dd to one zvol, 8k volblocksize, no O_DIRECT:
legacy submit_bio() 292MB/s write 453MB/s read
this commit 453MB/s write 885MB/s read
It also introduces a new `zvol_blk_mq_chunks_per_thread` module
parameter. This parameter represents how many volblocksize'd chunks
to process per each zvol thread. It can be used to tune your zvols
for better read vs write performance (higher values favor write,
lower favor read).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13148
Issue #12483
This commit adds BLAKE3 checksums to OpenZFS, it has similar
performance to Edon-R, but without the caveats around the latter.
Homepage of BLAKE3: https://github.com/BLAKE3-team/BLAKE3
Wikipedia: https://en.wikipedia.org/wiki/BLAKE_(hash_function)#BLAKE3
Short description of Wikipedia:
BLAKE3 is a cryptographic hash function based on Bao and BLAKE2,
created by Jack O'Connor, Jean-Philippe Aumasson, Samuel Neves, and
Zooko Wilcox-O'Hearn. It was announced on January 9, 2020, at Real
World Crypto. BLAKE3 is a single algorithm with many desirable
features (parallelism, XOF, KDF, PRF and MAC), in contrast to BLAKE
and BLAKE2, which are algorithm families with multiple variants.
BLAKE3 has a binary tree structure, so it supports a practically
unlimited degree of parallelism (both SIMD and multithreading) given
enough input. The official Rust and C implementations are
dual-licensed as public domain (CC0) and the Apache License.
Along with adding the BLAKE3 hash into the OpenZFS infrastructure a
new benchmarking file called chksum_bench was introduced. When read
it reports the speed of the available checksum functions.
On Linux: cat /proc/spl/kstat/zfs/chksum_bench
On FreeBSD: sysctl kstat.zfs.misc.chksum_bench
This is an example output of an i3-1005G1 test system with Debian 11:
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1196 1602 1761 1749 1762 1759 1751
skein-generic 546 591 608 615 619 612 616
sha256-generic 240 300 316 314 304 285 276
sha512-generic 353 441 467 476 472 467 426
blake3-generic 308 313 313 313 312 313 312
blake3-sse2 402 1289 1423 1446 1432 1458 1413
blake3-sse41 427 1470 1625 1704 1679 1607 1629
blake3-avx2 428 1920 3095 3343 3356 3318 3204
blake3-avx512 473 2687 4905 5836 5844 5643 5374
Output on Debian 5.10.0-10-amd64 system: (Ryzen 7 5800X)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1840 2458 2665 2719 2711 2723 2693
skein-generic 870 966 996 992 1003 1005 1009
sha256-generic 415 442 453 455 457 457 457
sha512-generic 608 690 711 718 719 720 721
blake3-generic 301 313 311 309 309 310 310
blake3-sse2 343 1865 2124 2188 2180 2181 2186
blake3-sse41 364 2091 2396 2509 2463 2482 2488
blake3-avx2 365 2590 4399 4971 4915 4802 4764
Output on Debian 5.10.0-9-powerpc64le system: (POWER 9)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1213 1703 1889 1918 1957 1902 1907
skein-generic 434 492 520 522 511 525 525
sha256-generic 167 183 187 188 188 187 188
sha512-generic 186 216 222 221 225 224 224
blake3-generic 153 152 154 153 151 153 153
blake3-sse2 391 1170 1366 1406 1428 1426 1414
blake3-sse41 352 1049 1212 1174 1262 1258 1259
Output on Debian 5.10.0-11-arm64 system: (Pi400)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 487 603 629 639 643 641 641
skein-generic 271 299 303 308 309 309 307
sha256-generic 117 127 128 130 130 129 130
sha512-generic 145 165 170 172 173 174 175
blake3-generic 81 29 71 89 89 89 89
blake3-sse2 112 323 368 379 380 371 374
blake3-sse41 101 315 357 368 369 364 360
Structurally, the new code is mainly split into these parts:
- 1x cross platform generic c variant: blake3_generic.c
- 4x assembly for X86-64 (SSE2, SSE4.1, AVX2, AVX512)
- 2x assembly for ARMv8 (NEON converted from SSE2)
- 2x assembly for PPC64-LE (POWER8 converted from SSE2)
- one file for switching between the implementations
Note the PPC64 assembly requires the VSX instruction set and the
kfpu_begin() / kfpu_end() calls on PowerPC were updated accordingly.
Reviewed-by: Felix Dörre <felix@dogcraft.de>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Closes#10058Closes#12918
As of the Linux 5.19 kernel the asm/fpu/internal.h header was
entirely removed. It has been effectively empty since the 5.16
kernel and provides no required functionality.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13529
As of the Linux 5.19 kernel an identically named zap_flags_t typedef
is declared in the include/linux/mm_types.h linux header. Sadly,
the inclusion of this header cannot be easily avoided. To resolve
the conflict a #define is used to remap the name in the OpenZFS
sources when building against the Linux kernel.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
As of the Linux 5.19 kernel the disk_*_io_acct() helper functions
have been replaced by the bdev_*_io_acct() functions.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
Linux 5.19 commit torvalds/linux@44abff2c0 removed the
blk_queue_secure_erase() helper function. The preferred
interface is to now use the bdev_max_secure_erase_sectors()
function to check for discard support.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
Linux 5.19 commit torvalds/linux@70200574cc removed the
blk_queue_discard() helper function. The preferred interface
is to now use the bdev_max_discard_sectors() function to check
for discard support.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
In current zil_commit() process, transaction lwb_tx is assigned in
zil_lwb_write_issue(), and is committed in zil_lwb_flush_vdevs_done().
Thus, during lwb write out process, the txg is held in open or quiesing
state, until zil_lwb_flush_vdevs_done() is called. If the zil's zio
latency is high, it will cause txg_sync_thread() to starve.
The goal here is to defer waiting for zil_lwb_flush_vdevs_done to the
'syncing' txg state. That is, in zil_sync().
In this patch, it achieves the goal without holding transaction.
A new function zil_lwb_flush_wait_all() is introduced. It waits for
the completion of all the zil_lwb_flush_vdevs_done() by given txg.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: jxdking <lostking2008@hotmail.com>
Closes#12321
This was breaking the kmod port build on FreeBSD with Clang 13.
Use the same trick as we do for ASSERT() to make DNODE_VERIFY() use
its parameter at compile time without actually using it at run time
in non-debug builds.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13507
- Make prefetch distance adaptive: up to 4MB prefetch doubles for
every, hit same as before, but after that it grows by 1/8 every time
the prefetch read does not complete in time to satisfy the demand.
My tests show that 4MB is sufficient for wide NVMe pool to saturate
single reader thread at 2.5GB/s, while new 64MB maximum allows the
same thread to reach 1.5GB/s on wide HDD pool. Further distance
increase may increase speed even more, but less dramatic and with
higher latency.
- Allow early reuse of inactive prefetch streams: streams that never
saw hits can be reused immediately if there is a demand, while others
can be reused after 1s of inactivity, starting with the oldest. After
2s of inactivity streams are deleted to free resources same as before.
This allows by several times increase strided read performance on HDD
pool in presence of simultaneous random reads, previously filling the
zfetch_max_streams limit for seconds and so blocking most of prefetch.
- Always issue intermediate indirect block reads with SYNC priority.
Each of those reads if delayed for longer may delay up to 1024 other
block prefetches, that may be not good for wide pools.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13452
It turns out that wrapping the atomic macro in () breaks build
on Linux/SPARC64. Oops.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13506
