In a4b21eadec we added the zap_micro_max_size tuneable to raise the size
at which "micro" (single-block) ZAPs are upgraded to "fat" (multi-block)
ZAPs. Before this, a microZAP was limited to 128KiB, which was the old
largest block size. The side effect of raising the max size past 128KiB
is that it be stored in a large block, requiring the large_blocks
feature.
Unfortunately, this means that a backup stream created without the
--large-block (-L) flag to zfs send would split the microZAP block into
smaller blocks and send those, as is normal behaviour for large blocks.
This would be received correctly, but since microZAPs are limited to the
first block in the object by definition, the entries in the later blocks
would be inaccessible. For directory ZAPs, this gives the appearance of
files being lost.
This commit adds a feature flag, large_microzap, that must be enabled
for microZAPs to grow beyond 128KiB, and which will be activated the
first time that occurs. This feature is later checked when generating
the stream and if active, the send operation will abort unless
--large-block has also been requested.
Changing the limit still requires zap_micro_max_size to be changed. The
state of this flag effectively sets the upper value for this tuneable,
that is, if the feature is disabled, the tuneable will be clamped to
128KiB.
A stream flag is also added to ensure that the receiver also activates
its own feature flag upon receiving the stream. This is not strictly
necessary to _use_ the received microZAP, since it doesn't care how
large its block is, but it is required to send the microZAP object on,
otherwise the original problem occurs again.
Because it's difficult to reliably distinguish a microZAP from a fatZAP
from outside the ZAP code, and because it seems unlikely that most
users are affected (a fairly niche tuneable combined with what should be
an uncommon use of send), and for the sake of expediency, this change
activates the feature the first time a microZAP grows to use a large
block, and is never deactivated after that. This can be improved in the
future.
This commit changes nothing for existing pools that already have large
microZAPs. The feature will not be retroactively applied, but will be
activated the next time a microZAP grows past the limit.
Don't use large_blocks feature for enable/disable tests. The
large_microzap depends on large_blocks, so it gets enabled as a
dependency, breaking the test. Instead use feature "longname", which has
the exact same feature characteristics.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16593
Current output:
> receiving correctivefull stream of a into b
New output:
> receiving corrective full stream of a into b
Signed-off-by: glibg10b <56197853+glibg10b@users.noreply.github.com>
Reviewed-by: Rob Norris <rob.norris@klarasystems.com>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
C99 6.7.8.17 says that when an undesignated initialiser is used, only
the first element of a union is initialised. If the first element is not
the largest within the union, how the remaining space is initialised is
up to the compiler.
GCC extends the initialiser to the entire union, while Clang treats the
remainder as padding, and so initialises according to whatever
automatic/implicit initialisation rules are currently active.
When Linux is compiled with CONFIG_INIT_STACK_ALL_PATTERN,
-ftrivial-auto-var-init=pattern is added to the kernel CFLAGS. This flag
sets the policy for automatic/implicit initialisation of variables on
the stack.
Taken together, this means that when compiling under
CONFIG_INIT_STACK_ALL_PATTERN on Clang, the "zero" initialiser will only
zero the first element in a union, and the rest will be filled with a
pattern. This is significant for aes_ctx_t, which in
aes_encrypt_atomic() and aes_decrypt_atomic() is initialised to zero,
but then used as a gcm_ctx_t, which is the fifth element in the union,
and thus gets pattern initialisation. Later, it's assumed to be zero,
resulting in a hang.
As confusing and undiscoverable as it is, by the spec, we are at fault
when we initialise a structure containing a union with the zero
initializer. As such, this commit replaces these uses with an explicit
memset(0).
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16135Closes#16206
Reviewed-by: Rob Norris <robn@despairlabs.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jason Lee <jasonlee@lanl.gov>
Closes#16074
POSIX timers target the process, not the thread (as does SIGINFO),
so we need to block it in the main thread which will die if interrupted.
Ref: https://101010.pl/@ed1conf@bsd.network/110731819189629373
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#15113
f6a0dac84 modified the zfs_iter_* functions to take a new "flags"
parameter, and introduced a variety of flags to ask the kernel to limit
the results in various ways, reducing the amount of work the caller
needed to do to filter out things they didn't need.
Unfortunately this change broke the ABI for existing clients (read:
older versions of the `zfs` program), and was reverted 399b98198.
dc95911d2 reintroduced the original patch, with the understanding that a
backwards-compatible fix would be made before the 2.2 release branch was
tagged. This commit is that fix.
This introduces zfs_iter_*_v2 functions that have the new flags
argument, and reverts the existing functions to not have the flags
parameter, as they were before. The old functions are now reimplemented
in terms of the new, with flags set to 0.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Original-patch-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Closes#14597
After addressing coverity complaints involving `nvpair_name()`, the
compiler started complaining about dropping const. This lead to a rabbit
hole where not only `nvpair_name()` needed to be constified, but also
`nvpair_value_string()`, `fnvpair_value_string()` and a few other static
functions, plus variable pointers throughout the code. The result became
a fairly big change, so it has been split out into its own patch.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14612
The intent is that this is like ENOTSUP, but specifically for when
something can't be done because we have no support for the requested
crypto parameters; eg unlocking a dataset or receiving a stream
encrypted with a suite we don't support.
Its not intended to be recoverable without upgrading ZFS itself.
If the request could be made to work by enabling a feature or modifying
some other configuration item, then some other code should be used.
load-key: In the future we might have more crypto suites (ie new values
for the `encryption` property. Right now trying to load a key on such
a future crypto suite will look up suite parameters off the end of the
crypto table, resulting in misbehaviour and/or crashes (or, with debug
enabled, trip the assertion in `zio_crypt_key_unwrap`).
Instead, lets check the value we got from the dataset, and if we can't
handle it, abort early.
recv: When receiving a raw stream encrypted with an unknown crypto
suite, `zfs recv` would report a generic `invalid backup stream`
(EINVAL). While technically correct, its not super helpful, so lets
ship a more specific error code and message.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#14577
strlcat() is supposed to be given the length of the destination buffer,
including the existing contents. Unfortunately, I had been overzealous
when I wrote a51288aabb, since I gave it
the length of the destination buffer, minus the existing contents. This
likely caused a regression on large strings.
On the topic of being overzealous, the use of strlcat() in
dmu_send_estimate_fast() was unnecessary because recv_clone_name is a
fixed length string. We continue using strlcat() mostly as defensive
programming, in case the string length is ever changed, even though it
is unnecessary.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14476
After commit 19d3961, progress reporting (-v) with replication flag
enabled does not report the progress on the console. This commit
fixes the issue by updating the logic to check for pa->progress
instead of pa_verbosity in send_progress_thread().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14448
In the zstream code, Coverity reported:
"The argument could be controlled by an attacker, who could invoke the
function with arbitrary values (for example, a very high or negative
buffer size)."
It did not report this in the kernel. This is likely because the
userspace code stored this in an int before passing it into the
allocator, while the kernel code stored it in a uint32_t.
However, this did reveal a potentially real problem. On 32-bit systems
and systems with only 4GB of physical memory or less in general, it is
possible to pass a large enough value that the system will hang. Even
worse, on Linux systems, the kernel memory allocator is not able to
support allocations up to the maximum 4GB allocation size that this
allows.
This had already been limited in userspace to 64MB by
`ZFS_SENDRECV_MAX_NVLIST`, but we need a hard limit in the kernel to
protect systems. After some discussion, we settle on 256MB as a hard
upper limit. Attempting to receive a stream that requires more memory
than that will result in E2BIG being returned to user space.
Reported-by: Coverity (CID-1529836)
Reported-by: Coverity (CID-1529837)
Reported-by: Coverity (CID-1529838)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14285
If zfs_receive_one() gets back EINVAL, check for the more likely case,
embedded block pointers + encryption and return that error, before
falling back to the less likely case, a resumable stream when the
kernel has not been upgraded to support resume.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Sponsored-by: rsync.net
Sponsored-by: Klara Inc.
Closes#14379
This allows parsing of zfs send progress by checking the process
title.
Doing so requires some changes to the send code in libzfs_sendrecv.c;
primarily these changes move some of the accounting around, to allow
for the code to be verbose as normal, or set the process title. Unlike
BSD, setproctitle() isn't standard in Linux; thus, borrowed it from
libbsd with slight modifications.
Authored-by: Sean Eric Fagan <sef@FreeBSD.org>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14376
Currently, the receiver fails to override the encryption
property for the plain replicated dataset with the error:
"cannot receive incremental stream: encryption property
'encryption' cannot be set for incremental streams.". The
problem is resolved by allowing the receiver to override
the encryption property for plain replicated send.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14253Closes#13533
If the fields to be listed and sorted by are constrained to those
populated by dsl_dataset_fast_stat(), then zfs list is much faster,
as it does not need to open each objset and reads its properties.
A previous optimization by Pawel Dawidek
(0cee24064a) took advantage
of this to make listing snapshot names sorted only by name much faster.
However, it was limited to `-o name -s name`, this work extends this
optimization to work with:
- name
- guid
- createtxg
- numclones
- inconsistent
- redacted
- origin
and could be further extended to any other properties supported by
dsl_dataset_fast_stat() or similar, that do not require extra locking
or reading from disk.
This was committed before (9a9e2e343dfa2af28bf7910de77ae73aa006de62),
but was reverted due to a regression when used with an older kernel.
If the kernel does not populate zc->zc_objset_stats, we now fallback
to getting the properties via the slower interface, to avoid problems
with newer userland and older kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#14110
`zfs_send_cb_impl()` calls `dump_filesystems()`, which calls
`dump_filesystem()`, which will return `-1` as an error when
`zfs_open()` returns `NULL`.
This will be passed to `zfs_standard_error()`, which passes it to
`zfs_standard_error_fmt()`, which passes it to `strerror()`.
To fix this, we modify zfs_open() to set `errno` whenever it returns
NULL. Most of the cases already have `errno` set (since they pass it to
`zfs_standard_error_fmt()`, which makes this easy. Then we modify
`dump_filesystem()` to pass `errno` instead of `-1`.
Reported-by: Coverity (CID-1524598)
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14264
Squelch false positives reported by GCC 12 with UBSan.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#14150
These were categorized as the following:
* Dead assignment 23
* Dead increment 4
* Dead initialization 6
* Dead nested assignment 18
Most of these are harmless, but since actual issues can hide among them,
we correct them.
That said, there were a few return values that were being ignored that
appeared to merit some correction:
* `destroy_callback()` in `cmd/zfs/zfs_main.c` ignored the error from
`destroy_batched()`. We handle it by returning -1 if there is an
error.
* `zfs_do_upgrade()` in `cmd/zfs/zfs_main.c` ignored the error from
`zfs_for_each()`. We handle it by doing a binary OR of the error
value from the subsequent `zfs_for_each()` call to the existing
value. This is how errors are mostly handled inside `zfs_for_each()`.
The error value here is passed to exit from the zfs command, so doing
a binary or on it is better than what we did previously.
* `get_zap_prop()` in `module/zfs/zcp_get.c` ignored the error from
`dsl_prop_get_ds()` when the property is not of type string. We
return an error when it does. There is a small concern that the
`zfs_get_temporary_prop()` call would handle things, but in the case
that it does not, we would be pushing an uninitialized numval onto
the lua stack. It is expected that `dsl_prop_get_ds()` will succeed
anytime that `zfs_get_temporary_prop()` does, so that not giving it a
chance to fix things is not a problem.
* `draid_merge_impl()` in `tests/zfs-tests/cmd/draid.c` used
`nvlist_add_nvlist()` twice in ways in which errors are expected to
be impossible, so we switch to `fnvlist_add_nvlist()`.
A few notable ones did not merit use of the return value, so we
suppressed it with `(void)`:
* `write_free_diffs()` in `lib/libzfs/libzfs_diff.c` ignored the error
value from `describe_free()`. A look through the commit history
revealed that this was intentional.
* `arc_evict_hdr()` in `module/zfs/arc.c` did not need to use the
returned handle from `arc_hdr_realloc()` because it is already
referenced in lists.
* `spa_vdev_detach()` in `module/zfs/spa.c` has a comment explicitly
saying not to use the error from `vdev_label_init()` because whatever
causes the error could be the reason why a detach is being done.
Unfortunately, I am not presently able to analyze the kernel modules
with Clang's static analyzer, so I could have missed some cases of this.
In cases where reports were present in code that is duplicated between
Linux and FreeBSD, I made a conscious effort to fix the FreeBSD version
too.
After this commit is merged, regressions like dee8934 should become
extremely obvious with Clang's static analyzer since a regression would
appear in the results as the only instance of unused code. That assumes
that Coverity does not catch the issue first.
My local branch with fixes from all of my outstanding non-draft pull
requests shows 118 reports from Clang's static anlayzer after this
patch. That is down by 51 from 169.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13986
GCC 12.1.1_p20220625's static analyzer caught these.
Of the two in the btree test, one had previously been caught by Coverity
and Smatch, but GCC flagged it as a false positive. Upon examining how
other test cases handle this, the solution was changed from
`ASSERT3P(node, !=, NULL);` to using `perror()` to be consistent with
the fixes to the other fixes done to the ZTS code.
That approach was also used in ZED since I did not see a better way of
handling this there. Also, upon inspection, additional unchecked
pointers from malloc()/calloc()/strdup() were found in ZED, so those
were handled too.
In other parts of the code, the existing methods to avoid issues from
memory allocators returning NULL were used, such as using
`umem_alloc(size, UMEM_NOFAIL)` or returning `ENOMEM`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13979
Coverity caught unsafe use of `strcpy()` in `ztest_dmu_objset_own()`,
`nfs_init_tmpfile()` and `dump_snapshot()`. It also caught an unsafe use
of `strlcat()` in `nfs_init_tmpfile()`.
Inspired by this, I did an audit of every single usage of `strcpy()` and
`strcat()` in the code. If I could not prove that the usage was safe, I
changed the code to use either `strlcpy()` or `strlcat()`, depending on
which function was originally used. In some cases, `snprintf()` was used
to replace multiple uses of `strcat` because it was cleaner.
Whenever I changed a function, I preferred to use `sizeof(dst)` when the
compiler is able to provide the string size via that. When it could not
because the string was passed by a caller, I checked the entire call
tree of the function to find out how big the buffer was and hard coded
it. Hardcoding is less than ideal, but it is safe unless someone shrinks
the buffer sizes being passed.
Additionally, Coverity reported three more string related issues:
* It caught a case where we do an overlapping memory copy in a call to
`snprintf()`. We fix that via `kmem_strdup()` and `kmem_strfree()`.
* It caught `sizeof (buf)` being used instead of `buflen` in
`zdb_nicenum()`'s call to `zfs_nicenum()`, which is passed to
`snprintf()`. We change that to pass `buflen`.
* It caught a theoretical unterminated string passed to `strcmp()`.
This one is likely a false positive, but we have the information
needed to do this more safely, so we change this to silence the false
positive not just in coverity, but potentially other static analysis
tools too. We switch to `strncmp()`.
* There was a false positive in tests/zfs-tests/cmd/dir_rd_update.c. We
suppress it by switching to `snprintf()` since other static analysis
tools might complain about it too. Interestingly, there is a possible
real bug there too, since it assumes that the passed directory path
ends with '/'. We add a '/' to fix that potential bug.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13913
When receiving full/newfs on existing dataset, then it should be done
with "-F" flag. Its enforced for initial receive in checks done in
zfs_receive_one function of libzfs. Similarly, on resuming full/newfs
recv on existing dataset, it should be done with "-F" flag.
When dataset doesn't exist, then full/new recv is done on newly created
dataset and it's marked INCONSISTENT. But when receiving on existing
dataset, recv is first done on %recv and its marked INCONSISTENT.
Existing dataset is not marked INCONSISTENT. Resume of full/newfs
receive with dataset not INCONSISTENT indicates that its resuming newfs
on existing dataset. So, enforce "-F" flag in this case.
Also return an error from dmu_recv_resume_begin_check() in zfs kernel,
when its resuming full/newfs recv without force.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chunwei Chen <david.chen@nutanix.com>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#13856Closes#13857
This reverts commit 80a650b7bb. This change
inadvertently introduced a regression in ztest where one of the new ASSERTs
is triggered in dsl_scan_visitbp().
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #12275Closes#13799
This type of recv is used to heal corrupted data when a replica
of the data already exists (in the form of a send file for example).
With the provided send stream, corrective receive will read from
disk blocks described by the WRITE records. When any of the reads
come back with ECKSUM we use the data from the corresponding WRITE
record to rewrite the corrupted block.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Alek Pinchuk <apinchuk@axcient.com>
Closes#9372
The current codebase does not support raw sending buffers with block
size > 128kB when large_blocks is not active. This can happen in the
codepath dsl_dataset_sync()->dmu_objset_sync()->zio_nowait() which
calls back dmu_objset_write_done()->dsl_dataset_block_born(). If
dsl_dataset_sync() completes its run before dsl_dataset_block_born() is
called, we will end up not activating some of the necessary flags, while
having blocks based on those flags written in the filesystem. A
subsequent send will then panic.
Fix this by directly deciding in dmu_objset_sync() whether these flags
need to be activated later by dsl_dataset_sync(). Instead of panicking
due to a NULL pointer dereference in dmu_dump_write() in case of a send,
print out an error message. Also during scrub verify there are no
contradicting filesystem flags.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12275Closes#12438
zfs_send_cb_impl fails to report error for some flags.
Use second error variable for send_conclusion_record.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13558
Every errbuf array in libzfs is 1024 chars.
Define ERRBUFLEN in a shared header, and use it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13539
This is in line with all the other uses of the progress thread
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11560Closes#13284
bcopy() has a confusing argument order and is actually a move, not a
copy; they're all deprecated since POSIX.1-2001 and removed in -2008,
and we shim them out to mem*() on Linux anyway
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12996
By introducing lzc_send_wrapper() and routing all ZFS_IOC_SEND*
users through it, we fix a Linux 5.10-introduced bug (see comment)
This is all /transparent/ to the users API, ABI, and usage-wise,
and disabled on FreeBSD and if the output is already a pipe,
and transparently nestable (i.e. zfs_send_one() is wrapped,
but so is lzc_send_redacted() it calls to ‒ this wouldn't be strictly
necessary if ZFS_IOC_SEND_PROGRESS wasn't strictly denominational w.r.t.
the descriptor the send is happening on)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11445Closes#13133
Notably, this also means that the pipe is expanded before each
dataset is received, so updates to /p/s/f/pipe-max-size are reflected
for each new dataset
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13133
New `zfs_type_t` value `ZFS_TYPE_INVALID` is introduced.
Variable initialization is now possible to make GCC happy.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12167Closes#13103
Provide two digits of precision when reporting send/receive
times. Tiny snapshots may take significantly less than a second
and rounding up to a full second can introduce a significant error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13047
Unfortunately macOS has obj-C keyword "fallthrough" in the OS headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#13097
`configure` now accepts `--enable-asan` and `--enable-ubsan` switches
which results in passing `-fsanitize=address`
and `-fsanitize=undefined`, respectively, to the compiler. Those
flags are enabled in GitHub workflows for ZTS and zloop. Errors
reported by both instrumentations are corrected, except for:
- Memory leak reporting is (temporarily) suppressed. The cost of
fixing them is relatively high compared to the gains.
- Checksum computing functions in `module/zcommon/zfs_fletcher*`
have UBSan errors suppressed. It is completely impractical
to enforce 64-byte payload alignment there due to performance
impact.
- There's no ASan heap poisoning in `module/zstd/lib/zstd.c`. A custom
memory allocator is used there rendering that measure
unfeasible.
- Memory leaks detection has to be suppressed for `cmd/zvol_id`.
`zvol_id` is run by udev with the help of `ptrace(2)`. Tracing is
incompatible with memory leaks detection.
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12928
Improve the readability of zfs_send_resume_impl by moving resume nvl
decoding into a separate helper function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12967
Factor out get_bookmarks, find_redact_pair, and get_redact_complete
helper functions to improve the readability of find_redact_book.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12967
* Capitalize and punctuate complete sentences.
* Add a blank line between functions.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12967
* Add a high level comment.
* Eliminate unnecessarily void arg.
* Capitalize and punctuate complete sentences in comments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12967
* Add a high level comment.
* Avoid unnecessary line wrapping.
* Simplify size accounting logic.
* Eliminate unnecessary buffer on the stack.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12967
