- Make prefetch distance adaptive: up to 4MB prefetch doubles for
every, hit same as before, but after that it grows by 1/8 every time
the prefetch read does not complete in time to satisfy the demand.
My tests show that 4MB is sufficient for wide NVMe pool to saturate
single reader thread at 2.5GB/s, while new 64MB maximum allows the
same thread to reach 1.5GB/s on wide HDD pool. Further distance
increase may increase speed even more, but less dramatic and with
higher latency.
- Allow early reuse of inactive prefetch streams: streams that never
saw hits can be reused immediately if there is a demand, while others
can be reused after 1s of inactivity, starting with the oldest. After
2s of inactivity streams are deleted to free resources same as before.
This allows by several times increase strided read performance on HDD
pool in presence of simultaneous random reads, previously filling the
zfetch_max_streams limit for seconds and so blocking most of prefetch.
- Always issue intermediate indirect block reads with SYNC priority.
Each of those reads if delayed for longer may delay up to 1024 other
block prefetches, that may be not good for wide pools.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13452
Original Log Size Limit implementation blocked all writes in case of
limit reached until the TXG is committed and the log is freed. It
caused huge delays and following speed spikes in application writes.
This implementation instead smoothly throttles writes, using exactly
the same mechanism as used for dirty data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: jxdking <lostking2008@hotmail.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Issue #12284Closes#13476
It turns out that "do LZ4 and zstd-1 both fail" is a great heuristic
for "don't even bother trying higher zstd tiers".
By way of illustration:
$ cat /incompress | mbuffer | zfs recv -o compression=zstd-12 evenfaster/lowcomp_1M_zstd12_normal
summary: 39.8 GiByte in 3min 40.2sec - average of 185 MiB/s
$ echo 3 | sudo tee /sys/module/zzstd/parameters/zstd_lz4_pass
3
$ cat /incompress | mbuffer -m 4G | zfs recv -o compression=zstd-12 evenfaster/lowcomp_1M_zstd12_patched
summary: 39.8 GiByte in 48.6sec - average of 839 MiB/s
$ sudo zfs list -p -o name,used,lused,ratio evenfaster/lowcomp_1M_zstd12_normal evenfaster/lowcomp_1M_zstd12_patched
NAME USED LUSED RATIO
evenfaster/lowcomp_1M_zstd12_normal 39549931520 42721221632 1.08
evenfaster/lowcomp_1M_zstd12_patched 39626399744 42721217536 1.07
$ python3 -c "print(39626399744 - 39549931520)"
76468224
$
I'll take 76 MB out of 42 GB for > 4x speedup.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13244
The short-path is now one access() call,
we always modprobe zfs (ZFS_MODULE_LOADING which doesn't use the libzfs
boolean parsing is gone),
and we use a simple inotify IN_CREATE loop with a timerfd timeout
rather than 10ms kernel-style polling
There's one substantial difference: ZFS_MODULE_TIMEOUT=-1
now means "never give up", rather than "wait 10 minutes"
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13330
This changes the behaviour of -B from the illumos one which would,
in the example in the manual, take just ./chroots/lenny;
this, however, is more versatile, and scales much better for systems
with ZFS in /usr/local, for example
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13411Closes#1770
No installation diff, dist lost
-zfs-2.1.99/cmd/fsck_zfs/fsck.zfs
which was distributed erroneously, since it's generated
Also clean gitrev on clean
Also add -e 'any possible bashisms' to default checkbashisms flags,
and fully parallelise it and shellcheck, and it works out-of-tree, too
Also align the Release in the dist META file correctly
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13316
Linux has an unresolved hang if you resize a pipe with bytes
in it.
Since there's no obvious way to detect this happening, added a
workaround to disable resizing the pipe buffer if you set an
environment variable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13309
When calculating mg_aliquot alike to #12046 use number of unique data
disks in the vdev, not the total number of children vdev. Increase
default value of the tunable from 512KB to 1MB to compensate.
Before this change each disk in striped pool was getting 512KB of
sequential data, in 2-wide mirror -- 1MB, in 3-wide RAIDZ1 -- 768KB.
After this change in all the cases each disk should get 1MB.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13388
Increase the default allowed maximum recordsize from 1M to 16M.
As described in the zfs(4) man page, there are significant costs
which need to be considered before using very large blocks.
However, there are scenarios where they make good sense and
it should no longer be necessary to artificially restrict their
use behind a module option.
Note that for 32-bit platforms we continue to leave this
restriction in place due to the limited virtual address space
available (256-512MB). On these systems only a handful
of blocks could be cached at any one time severely impacting
performance and potentially stability.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12830Closes#13302
Previous flushing algorithm limited only total number of log blocks to
the minimum of 256K and 4x number of metaslabs in the pool. As result,
system with 1500 disks with 1000 metaslabs each, touching several new
metaslabs each TXG could grow spacemap log to huge size without much
benefits. We've observed one of such systems importing pool for about
45 minutes.
This patch improves the situation from five sides:
- By limiting maximum period for each metaslab to be flushed to 1000
TXGs, that effectively limits maximum number of per-TXG spacemap logs
to load to the same number.
- By making flushing more smooth via accounting number of metaslabs
that were touched after the last flush and actually need another flush,
not just ms_unflushed_txg bump.
- By applying zfs_unflushed_log_block_pct to the number of metaslabs
that were touched after the last flush, not all metaslabs in the pool.
- By aggressively prefetching per-TXG spacemap logs up to 16 TXGs in
advance, making log spacemap load process for wide HDD pool CPU-bound,
accelerating it by many times.
- By reducing zfs_unflushed_log_block_max from 256K to 128K, reducing
single-threaded by nature log processing time from ~10 to ~5 minutes.
As further optimization we could skip bumping ms_unflushed_txg for
metaslabs not touched since the last flush, but that would be an
incompatible change, requiring new pool feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12789
Currently, determining which datasets are affected by corruption is
a manual process.
The primary difficulty in reporting the list of affected snapshots is
that since the error was initially found, the snapshot where the error
originally occurred in, may have been deleted. To solve this issue, we
add the ID of the head dataset of the original snapshot which the error
was detected in, to the stored error report. Then any time a filesystem
is deleted, the errors associated with it are deleted as well. Any time
a clone promote occurs, we modify reports associated with the original
head to refer to the new head. The stored error reports are identified
by this head ID, the birth time of the block which the error occurred
in, as well as some information about the error itself are also stored.
Once this information is stored, we can find the set of datasets
affected by an error by walking back the list of snapshots in the given
head until we find one with the appropriate birth txg, and then traverse
through the snapshots of the clone family, terminating a branch if the
block was replaced in a given snapshot. Then we report this information
back to libzfs, and to the zpool status command, where it is displayed
as follows:
pool: test
state: ONLINE
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the
entire pool from backup.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-8A
scan: scrub repaired 0B in 00:00:00 with 800 errors on Fri Dec 3
08:27:57 2021
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
sdb ONLINE 0 0 1.58K
errors: Permanent errors have been detected in the following files:
test@1:/test.0.0
/test/test.0.0
/test/1clone/test.0.0
A new feature flag is introduced to mark the presence of this change, as
well as promotion and backwards compatibility logic. This is an updated
version of #9175. Rebase required fixing the tests, updating the ABI of
libzfs, updating the man pages, fixing bugs, fixing the error returns,
and updating the old on-disk error logs to the new format when
activating the feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain <tulsi.jain@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#9175Closes#12812
Also clean up the horrendously verbose -X handling in zfs_main()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13352
Thorough documentation with a dracut.bootup(7)-style flowchart,
dracut.cmdline(7)-style cmdline listing,
and per-file docs like the old README
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13291
Provide explicit requirements towards file system naming convention
in OpenZFS man pages.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Mitigates #13310Closes#13315
Remove handling for allowing doxygen- and embedding in splint(?)-style
comments. This functionality is unused by OpenZFS.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13264
Add support for a -exclude/-X option to `zfs send` to allow dataset
hierarchies to be excluded.
Snapshots can be excluded using a channel program; however,
this can result in failures with 'zfs send -R'; this option allows
them to be excluded. Fortunately, this required a change only to
cmd/zfs/zfs_main.c, using the already-existing callback argument
to zfs_send() that is currently unused.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Sean Eric Fagan <kithrup@mac.com>
Signed-off-by: Sean Eric Fagan <kithrup@mac.com>
Closes#13158
A simple change, but so many tests break with it,
and those are the majority of this.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13078
As such, there are no specific synchronous semantics defined for
the xattrs. But for xattr=on, it does log to ZIL and zil_commit() is
done, if sync=always is set on dataset. This provides sync semantics
for xattr=on with sync=always set on dataset.
For the xattr=sa implementation, it doesn't log to ZIL, so, even with
sync=always, xattrs are not guaranteed to be synced before xattr call
returns to caller. So, xattr can be lost if system crash happens, before
txg carrying xattr transaction is synced.
This change adds xattr=sa logging to ZIL on xattr create/remove/update
and xattrs are synced to ZIL (zil_commit() done) for sync=always.
This makes xattr=sa behavior similar to xattr=on.
Implementation notes:
The actual logging is fairly straight-forward and does not warrant
additional explanation.
However, it has been 14 years since we last added new TX types
to the ZIL [1], hence this is the first time we do it after the
introduction of zpool features. Therefore, here is an overview of the
feature activation and deactivation workflow:
1. The feature must be enabled. Otherwise, we don't log the new
record type. This ensures compatibility with older software.
2. The feature is activated per-dataset, since the ZIL is per-dataset.
3. If the feature is enabled and dataset is not for zvol, any append to
the ZIL chain will activate the feature for the dataset. Likewise
for starting a new ZIL chain.
4. A dataset that doesn't have a ZIL chain has the feature deactivated.
We ensure (3) by activating on the first zil_commit() after the feature
was enabled. Since activating the features requires waiting for txg
sync, the first zil_commit() after enabling the feature will be slower
than usual. The downside is that this is really a conservative
approximation: even if we never append a 'TX_SETSAXATTR' to the ZIL
chain, we pay the penalty for feature activation. The upside is that the
user is in control of when we pay the penalty, i.e., upon enabling the
feature.
We ensure (4) by hooking into zil_sync(), where ZIL destroy actually
happens.
One more piece on feature activation, since it's spread across
multiple functions:
zil_commit()
zil_process_commit_list()
if lwb == NULL // first zil_commit since zil_open
zil_create()
if no log block pointer in ZIL header:
if feature enabled and not active:
// CASE 1
enable, COALESCE txg wait with dmu_tx that allocated the
log block
else // log block was allocated earlier than this zil_open
if feature enabled and not active:
// CASE 2
enable, EXPLICIT txg wait
else // already have an in-DRAM LWB
if feature enabled and not active:
// this happens when we enable the feature after zil_create
// CASE 3
enable, EXPLICIT txg wait
[1] da6c28aaf6
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#8768Closes#9078
ZFS on Linux originally implemented xattr namespaces in a way that is
incompatible with other operating systems. On illumos, xattrs do not
have namespaces. Every xattr name is visible. FreeBSD has two
universally defined namespaces: EXTATTR_NAMESPACE_USER and
EXTATTR_NAMESPACE_SYSTEM. The system namespace is used for protected
FreeBSD-specific attributes such as MAC labels and pnfs state. These
attributes have the namespace string "freebsd:system:" prefixed to the
name in the encoding scheme used by ZFS. The user namespace is used
for general purpose user attributes and obeys normal access control
mechanisms. These attributes have no namespace string prefixed, so
xattrs written on illumos are accessible in the user namespace on
FreeBSD, and xattrs written to the user namespace on FreeBSD are
accessible by the same name on illumos.
Linux has several xattr namespaces. On Linux, ZFS encodes the
namespace in the xattr name for every namespace, including the user
namespace. As a consequence, an xattr in the user namespace with the
name "foo" is stored by ZFS with the name "user.foo" and therefore
appears on FreeBSD and illumos to have the name "user.foo" rather than
"foo". Conversely, none of the xattrs written on FreeBSD or illumos
are accessible on Linux unless the name happens to be prefixed with one
of the Linux xattr namespaces, in which case the namespace is stripped
from the name. This makes xattrs entirely incompatible between Linux
and other platforms.
We want to make the encoding of user namespace xattrs compatible across
platforms. A critical requirement of this compatibility is for xattrs
from existing pools from FreeBSD and illumos to be accessible by the
same names in the user namespace on Linux. It is also necessary that
existing pools with xattrs written by Linux retain access to those
xattrs by the same names on Linux. Making user namespace xattrs from
Linux accessible by the correct names on other platforms is important.
The handling of other namespaces is not required to be consistent.
Add a fallback mechanism for listing and getting xattrs to treat xattrs
as being in the user namespace if they do not match a known prefix.
Do not allow setting or getting xattrs with a name that is prefixed
with one of the namespace names used by ZFS on supported platforms.
Allow choosing between legacy illumos and FreeBSD compatibility and
legacy Linux compatibility with a new tunable. This facilitates
replication and migration of pools between hosts with different
compatibility needs.
The tunable controls whether or not to prefix the namespace to the
name. If the xattr is already present with the alternate prefix,
remove it so only the new version persists. By default the platform's
existing convention is used.
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11919
It's noted very scarcely in the code as it stands, indeed the only
actual comment on this is
/*
* We have finished background destroying, but there is still
* some space left in the dp_free_dir. Transfer this leaked
* space to the dp_leak_dir.
*/
Introduced in fbeddd60b7 ("Illumos 4390 -
I/O errors can corrupt space map when deleting fs/vol"),
which explains, alongside the references, that this can only happen
with a corrupted pool
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13081
Should be `-o keyformat=passphrase` instead of `-o -keyformat=passphrase`
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chuang Zhu <chuang@melty.land>
Closes#13072
zdb -d <pool>/<objset ID> does not work when
other command line arguments are included i.e.
zdb -U <cachefile> -d <pool>/<objset ID>
This change fixes the command line parsing
to handle this situation. Also fix issue
where zdb -r <dataset> <file> does not handle
the root <dataset> of the pool. Introduce -N
option to force <objset ID> to be interpreted
as a numeric objsetID.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#12845Closes#12944
Nowhere in the description of the failmode property does it
clearly state how to bring a suspended pool back online.
Add a few words to property description and the zpool-clear(8)
man page.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12907Closes#9395
This change introduces long options for zdb. It updates the usage
message as well to include the long options.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Manoj Joseph <manoj.joseph@delphix.com>
Closes#12818
On FreeBSD vnode reclamation is single-threaded, protected by single
global lock. Linux seems to be able to use a thread per mount point,
but at this time it creates more harm than good.
Reduce number of threads to 1, adding tunable in case somebody wants
to try more.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12896
Issue #9966
Timers can be enabled as follows:
systemctl enable zfs-scrub-weekly@rpool.timer --now
systemctl enable zfs-scrub-monthly@datapool.timer --now
Each timer will pull in zfs-scrub@${poolname}.service, which is not
schedule-specific.
Added PERIODIC SCRUB section to zpool-scrub.8.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Closes#12193
Strict hole reporting was previously disabled by default as a
performance optimization. However, this has lead to confusion
over the expected behavior and a variety of workarounds being
adopted by consumers of ZFS. Change the default behavior to
always report holes and force the TXG sync.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12746
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Max Zettlmeißl <max@zettlmeissl.de>
Closes#12784
Sometimes, we'd like to know info about the metaslab groups
on special vdevs too. So let's make -MM do something useful.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12750
* etc/systemd/zfs-mount-generator: serialise
The wins for a relatively normal workload are rather slim:
real 0.02119s/0.00985s=2.15029x
user 0.02130s/0.00346s=6.15560x
sys 0.03858s/0.00643s=6.00062x
wall-total 0.014518s/0.005925s=2.45009x
wall-init 0.014518s/0.002457s=5.90684x
wall-real 0.014518s/0.003467s=4.18668x
But this is a big win on machines with a lot of datasets and expensive
forks.
For example, the gain on a VM on my work laptop with 900+ legacy-mount
Docker datasets, the original gains from the C rewrite were
only five-fold:
real 0.516s/0.102s=5.05882x
user 0.237s/0.143s=1.65734x
sys 0.287s/0.100s=2.87x
And this serial variant gains this back there as well:
real 0.102s/0.008s=12.75x
user 0.143s/0.007s=20.42857
sys 0.100s/0.001s=100x
wall-total 0.09717s/0.00319s=30.40255x
wall-init 0.00203s/0.00200s=1.015941x
wall-real 0.09513s/0.00118s=80.02043x
For a total of
real 0.516s/0.008s=64.5x
user 0.237s/0.007s=33.85714x
sys 0.287s/0.001s=287x
Suggested-by: Richard Laager <rlaager@wiktel.com>
* etc/systemd/zfs-mount-generator: pull in network for keylocation=https
Also simplify RequiresMountsFor= handling
Ref: #11956
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12138
Add properties, similar to pool properties, to each vdev.
This makes use of the existing per-vdev ZAP that was added as
part of device evacuation/removal.
A large number of read-only properties are exposed,
many of the members of struct vdev_t, that provide useful
statistics.
Adds support for read-only "removing" vdev property.
Adds the "allocating" property that defaults to "on" and
can be set to "off" to prevent future allocations from that
top-level vdev.
Supports user-defined vdev properties.
Includes support for properties.vdev in SYSFS.
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11711
Update zpool.8 to avoid parseltongue.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Piotr P. Stefaniak <pstef@freebsd.org>
Closes#12763
The code is integrated, builds fine, runs fine, there's not really
any reason not to.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12735
Special allocation class or dedup vdevs may have roughly the same
performance as L2ARC vdevs. Introduce a new tunable to exclude those
buffers from being cacheable on L2ARC.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11761Closes#12285
In case if all label checksums will be invalid on any vdev, the pool
will become unimportable. The zhack with newly added cli options could
be used to restore label checksums and make pool importable again.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#2510Closes#12686
When using lseek(2) to report data/holes memory mapped regions of
the file were ignored. This could result in incorrect results.
To handle this zfs_holey_common() was updated to asynchronously
writeback any dirty mmap(2) regions prior to reporting holes.
Additionally, while not strictly required, the dn_struct_rwlock is
now held over the dirty check to prevent the dnode structure from
changing. This ensures that a clean dnode can't be dirtied before
the data/hole is located. The range lock is now also taken to
ensure the call cannot race with zfs_write().
Furthermore, the code was refactored to provide a dnode_is_dirty()
helper function which checks the dnode for any dirty records to
determine its dirtiness.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11900Closes#12724
This change primarily seeks to make implicit documentation explicit, as
it is not outright stated that options should be comma-separated, nor is
there a reason given for it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Daniel Ebdrup Jensen <debdrup@FreeBSD.org>
Closes#12579
Recognize when the host part of a sharenfs attribute is an ipv6
Literal and pass that through without modification.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Felix Dörre <felix@dogcraft.de>
Closes: #11171Closes#11939Closes: #1894
One might expect "send data as it is on disk, and cannot trigger
compression changes" to imply "does not attempt to compress data
that was not compressed on the sender."
One would be mistaken.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12570
Previously, zpool-iostat did not display any data regarding rebuild I/Os
in either the latency/size histograms (-w/-l/-r) or the queue data (-q).
This fix essentially utilizes the existing infrastructure for tracking
rebuild queue data and displays this data in the proper places within
zpool-iostat's output.
Signed-off-by: Trevor Bautista <tbautista@newmexicoconsortium.org>
Signed-off-by: Trevor Bautista <tbautista@lanl.gov>
Co-authored-by: Trevor Bautista <tbautista@newmexicoconsortium.org>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Document that top-level vdevs cannot be removed unless all top-level
vdevs have the same sector size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Sam Hathaway <sam@sam-hathaway.com>
Closes#11339Closes#12472
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Gordon Bergling <gbergling@googlemail.com>
Closes#12464
Many things has changed since previous default was set many years ago.
Nowadays 8KB does not allow adequate compression or even decent space
efficiency on many of pools due to 4KB disk physical block rounding,
especially on RAIDZ and DRAID. It effectively limits write throughput
to only 2-3GB/s (250-350K blocks/s) due to sync thread, allocation,
vdev queue and other block rate bottlenecks. It keeps L2ARC expensive
despite many optimizations and dedup just unrealistic.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12406
Describe sequential scrub and add examples of scrub status.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#12429
* Add Module Parameters Regarding Log Size Limit
zfs_wrlog_data_max
The upper limit of TX_WRITE log data. Once it is reached,
write operation is blocked, until log data is cleared out
after txg sync. It only counts TX_WRITE log with WR_COPIED
or WR_NEED_COPY.
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: jxdking <lostking2008@hotmail.com>
Closes#12284
zfs-send(8) claimed in the flags list you could use -pR when sending
a readonly filesystem or volume. You cannot.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12336
arc_evict_hdr() returns number of evicted bytes in scope of specific
state. For ghost states it does not mean the amount of really freed
memory, but the logical buffer size. It is correct for the eviction
process, but not for waking up threads waiting for ARC size reduction,
as added in "Revise ARC shrinker algorithm" commit, causing premature
wakeups while ARC is still overflowed, allowing even bigger overflow,
plus processing overhead when next allocation will also get blocked,
probably also for too short time.
To fix that make arc_evict_hdr() also return the amount of really
freed memory, which for the ghost states is only the header, and use
it to update arc_evict_count instead. Originally I was thinking to
not return it at all, since arc_get_data_impl() does not account for
the headers, but decided that some slow allocation progress is better
than long waits, reaching on my tests up to 100ms.
To reduce negative latency effects of long time periods when reclaim
thread can free little real memory, start reclamation process earlier,
before we actually reached the overflow threshold, when we have to
throttle new allocations. We can also do it without taking global
arc_evict_lock, reducing the contention.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12279
Most notably this fixes the vdev_id(8) non-.Xrs in vdev_id.conf.5
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12212
The prevailing style is to use either nothing, or the originating
organisational umbrella (here: OpenZFS), and these aren't Linux manpages
This also deduplicates the substitution code, and makes adding/removing
sexions simpler in future
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12212
zfs_arc_overflow_shift was never a parameter:
ca0bf58d65 ("Illumos 5497 - lock
contention on arcs_mtx") is the only result in
git log -Soverflow_shift, and it wasn't exposed then, nor is it now
zfs_read_chunk_size was renamed to zfs_vnops_read_chunk_size in
e53d678d4a ("Share zfs_fsync, zfs_read,
zfs_write, et al between Linux and FreeBSD")
zio_decompress_fail_fraction was never a parameter: it was added in
c3bd3fb4ac ("OpenZFS 9403 - assertion
failed in arc_buf_destroy()") as a developer aid for setting in zdb, but
it's a dangerous test tunable and has no place in public documentation,
(not to mention that it obviously doesn't work):
> Although this did uncover a few low priority issues, this
unfortuantely also causes ztest to ASSERT in many locations where the
code is working correctly since it is designed to fail on IO errors.
Developers can manually set this variable with the '-o' option to find
and debug issues.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12157
Both were removed in 4fbdb10c7b ("remove
kmem_cache module parameter KMC_EXPIRE_AGE")
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12157
Also yeet pci_slot since it doesn't seem to exist?
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12125
Also remove note about the OS/Net consolidation, now the illumos gate
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12125
The spacing on zhack feature stat pool is a bit iffy(?)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12125
Also rip out the section about potentially including in the OpenZFS
distribution and simplify -e description
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12125
Also re-add articles left out by the slav who wrote this
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12125
Also slim down the description a tad
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12125
I fixed a few typos, but avoided changing anything beyond that;
the sould of the document should be preserved
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12125
This change introduces long options for ztest. It builds the usage
message as well as the long_options array from a single table. It also
adds #defines for the default values.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Manoj Joseph <manoj.joseph@delphix.com>
Closes#12117
Previously, ZFS scaled maxinflight_bytes based on total number of
disks in the pool. A 3-wide mirror was receiving a queue depth of 3
disks, which it should not, since it reads from all the disks inside.
For wide raidz the situation was slightly better, but still a 3-wide
raidz1 received a depth of 3 disks instead of 2.
The new code counts only unique data disks, i.e. 1 disk for mirrors
and non-parity disks for raidz/draid. For draid the math is still
imperfect, since vdev_get_nparity() returns number of parity disks
per group, not per vdev, but still some better than it was.
This should slightly reduce scrub influence on payload for some pool
topologies by avoiding excessive queuing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closing #12046
A plain rewrite of the shell version, and generates identical
units, save for replacing some empty lines with nothing, having fewer
meaningless spaces in After=s and different spacing in the lock scripts,
for a clean git diff -w
This is a gain of anywhere from 0m0.336s vs 0m0.022s (15.27x)
to 0m0.202s vs 0m0.006s (33.67x), depending on the hardware,
a.k.a. from "absolutely unusable" to "perfectly fine"
This also properly deals with canmount=noauto units across multiple
pools
See PR for detailed timings (of an early version) and diffs
Reviewed-by: Antonio Russo <aerusso@aerusso.net>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: InsanePrawn <insane.prawny@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #11915Closes#11917
No changes to the text itself
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12111
Linux man-pages' mount(8) points at fcntl(2), as does mount(2),
and support for it is little-used, deprecated, and configurable
since 4.5.
As far as I can tell, FreeBSD doesn't support nbmand at all ‒
mandatory locks are mostly dead
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12111
zstreamdump(8) was in quite a bad state,
and the wrapper didn't work if invoked without /sbin in $PATH
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12015
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Lauri Tirkkonen <lauri@hacktheplanet.fi>
Closes#12064
While use of dynamic taskqs allows to reduce number of idle threads,
hardcoded 8 taskqs of each kind is a big overkill for small systems,
complicating CPU scheduling, increasing I/O reorder, etc, while
providing no real locking benefits, just not needed there.
On another side, 12*8 worker threads per kind are able to overload
almost any system nowadays. For example, pool of several fast SSDs
with SHA256 checksum makes system barely responsive during scrub, or
with dedup enabled barely responsive during large file deletion.
To address both problems this patch introduces ZTI_SCALE macro, alike
to ZTI_BATCH, but with multiple taskqs, depending on number of CPUs,
to be used in places where lock scalability is needed, while request
ordering is not so much. The code is made to create new taskq for
~6 worker threads (less for small systems, but more for very large)
up to 80% of CPU cores (previous 75% was not good for rounding down).
Both number of threads and threads per taskq are now tunable in case
somebody really wants to use all of system power for ZFS.
While obviously some benchmarks show small peak performance reduction
(not so big really, especially on systems with SMT, where use of the
second threads does not give as much performance as the first ones),
they also show dramatic latency reduction and much more smooth user-
space operation in case of high CPU usage by ZFS.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#11966
FreeBSD historically has not cared about the xattr property; it was
always treated as xattr=on. With xattr=on, xattrs are stored as files
in a hidden xattr directory. With xattr=sa, xattrs are stored as
system attributes and get cached in nvlists during xattr operations.
This makes SA xattrs simpler and more efficient to manipulate. FreeBSD
needs to implement the SA xattr operations for feature parity with
Linux and to ensure that SA xattrs are accessible when migrated or
replicated from Linux.
Following the example set by Linux, refactor our existing extattr vnops
to split off the parts handling dir style xattrs, and add the
corresponding SA handling parts.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11997
mandoc: ./man/man8/zfs-mount-generator.8.in:188:2:
ERROR: skipping end of block that is not open: RE
mandoc: ./man/man8/zfs_ids_to_path.8:38:2:
ERROR: skipping unknown macro: .LP
mandoc: ./man/man8/zfs_ids_to_path.8:48:2:
ERROR: inserting missing end of block: Sh breaks Bl
mandoc: ./man/man8/zfs-wait.8:69:2:
ERROR: skipping end of block that is not open: El
mandoc: ./man/man8/zfs-program.8:460:2:
ERROR: inserting missing end of block: It breaks Bd
mandoc: ./man/man8/zfs-mount-generator.8:188:2:
ERROR: skipping end of block that is not open: RE
mandoc: ./man/man8/zstream.8:43:2:
ERROR: skipping unknown macro: .LP
mandoc: ./man/man8/zstream.8:107:2:
ERROR: inserting missing end of block: Sh breaks Bl
mandoc: ./man/man8/zstream.8:107:2:
ERROR: inserting missing end of block: Sh breaks Bl
make: *** [Makefile:1529: mancheck] Error 1
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12017
Add support for http and https to the keylocation properly to
allow encryption keys to be fetched from the specified URL.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #9543Closes#9947Closes#11956
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11972
zfs_zevent_console committed multiple printk()s per line without
properly continuing them ‒ a single event could easily be fragmented
across over thirty lines, making it useless for direct application
zfs_zevent_cols exists purely to wrap the output from zfs_zevent_console
The niche this was supposed to fill can be better served by something
akin to the all-syslog ZEDLET
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#7082Closes#11996
Afterward, git grep ZoL matches:
* README.md: * [ZoL Site](https://zfsonlinux.org)
- Correct
* etc/default/zfs.in:# ZoL userland configuration.
- Changing this would induce a needless upgrade-check,
if the user has modified the configuration;
this can be updated the next time the defaults change
* module/zfs/dmu_send.c: * ZoL < 0.7 does not handle [...]
- Before 0.7 is ZoL, so fair enough
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #11956
Changed the default specified for zfs_dbgmsg_enable, added
clarification of interaction with zfs_flags.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#11984Closes#11986
The special_small_blocks section directed readers to zpool(8) for
documentation on special allocation classes, while they are actually
documented in zpoolconcepts(8).
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Daniel Stevenson <daniel@dstev.net>
Closes#11918
Before #11710 the flags in zfs-send(8) were sorted.
Restore order and bump the date.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11905
Traversal code, traverse_visitbp() does visit blocks recursively.
Indirect (Non L0) Block of size 128k could contain, 1024 block pointers
of 128 bytes. In case of full traverse OR incremental traverse, where
all blocks were modified, it could traverse large number of blocks
pointed by indirect. Traversal code does issue prefetch of blocks
traversed below indirect. This could result into large number of
async reads queued on vdev queue. So, account for prefetch issued for
blocks pointed by indirect and limit max prefetch in one go.
Module Param:
zfs_traverse_indirect_prefetch_limit: Limit of prefetch while traversing
an indirect block.
Local counters:
prefetched: Local counter to account for number prefetch done.
pidx: Index for which next prefetch to be issued.
ptidx: Index at which next prefetch to be triggered.
Keep "ptidx" somewhere in the middle of blocks prefetched, so that
blocks prefetch read gets the enough time window before their demand
read is issued.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#11802Closes#11803
Several improvements to the operation of the 'compatibility' property:
1) Improved handling of unrecognized features:
Change the way unrecognized features in compatibility files are handled.
* invalid features in files under /usr/share/zfs/compatibility.d
only get a warning (as these may refer to future features not yet in
the library),
* invalid features in files under /etc/zfs/compatibility.d
get an error (as these are presumed to refer to the current system).
2) Improved error reporting from zpool_load_compat.
Note: slight ABI change to zpool_load_compat for better error reporting.
3) compatibility=legacy inhibits all 'zpool upgrade' operations.
4) Detect when features are enabled outside current compatibility set
* zpool set compatibility=foo <-- print a warning
* zpool set feature@xxx=enabled <-- error
* zpool status <-- indicate this state
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11861
It's been observed in the CI that the required 25% of obsolete bytes
in the mapping can be to high a threshold for this test resulting in
condensing never being triggered and a test failure. To prevent these
failures make the existing zfs_condense_indirect_obsolete_pct tuning
available so the obsolete percentage can be reduced from 25% to 5%
during this test.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11869
