This fixes zfs-mount initscript trying to mount swap volumes
as filesystems or anything that has 'none' as a mountpoint
in /etc/fstab. Additionally, fixes trying to mount swap volumes
as a filesystem on RHEL. RHEL defines mountpoint for swap
as `swap`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Georgy Yakovlev <ya@sysdump.net>
Closes#7346Closes#7347
Authored by: Andriy Gapon <avg@FreeBSD.org>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Don Brady <don.brady@delphix.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Porting Notes:
* Re-enabled and tweaked the zpool_upgrade_007_pos test case
to successfully run in under 5 minutes.
OpenZFS-issue: https://www.illumos.org/issues/9164
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/0e776dc06aCloses#6112Closes#7336
Adds a devid for nvme devices. This is very similar to how the
other 'bus' (scsi|sata|usb) devids are generated. The devid
resides in a name/value pair in the leaf vdevs in a zpool config.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#7356
Currently, when ZFS wants to accelerate compression with QAT, it
passes a destination buffer of the same size as the source buffer.
Unfortunately, if the data is incompressible, QAT can actually
"compress" the data to be larger than the source buffer. When this
happens, the QAT driver will return a FAILED error code and print
warnings to dmesg. This patch fixes these issues by providing the
QAT driver with an additional buffer to work with so that even
completely incompressible source data will not cause an overflow.
This patch also resolves an error handling issue where
incompressible data attempts compression twice: once by QAT and
once in software. To fix this issue, a new (and fake) error code
CPA_STATUS_INOMPRESSIBLE has been added so that the calling code
can correctly account for the difference between a hardware
failure and data that simply cannot be compressed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Weigang Li <weigang.li@intel.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7338
This patch fixes an issue where dsl_scan_prefetch_cb() might
add more prefetch I/Os to the prefetch queue after prefetching
has been completed. This was happening because that code was
checking scn->scn_suspending instead of scn->scn_prefetch_stop.
This occasionally triggered an ASSERT during ztest runs in
dsl_scan_fini() when the code attempted to destroy an AVL tree
that still had entires in it. This patch also includes a number
of spelling corrections and comment cleanups throughout
dsl_scan.c
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7353
Clear executable bit on zfs-import.in, zfs-mount.in,
zfs-share.in, and zfs-zed.in. These are automake files and
should not be marked executable. This fixes a RPM build error
on Fedora 28.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7355Closes#7327
Calling uiomove() in mappedread() under the page lock can result
in a deadlock if the user space page needs to be faulted in.
Resolve the issue by dropping the page lock before the uiomove().
The inode range lock protects against concurrent updates via
zfs_read() and zfs_write().
Reviewed-by: Albert Lee <trisk@forkgnu.org>
Reviewed-by: Chunwei Chen <david.chen@nutanix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7335Closes#7339
RHEL/CentOS 6 supports sys/xattr.h eliminating the need for
libattr-devel as a dependency.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#7344Closes#7351
Authored by: Allan Jude <allanjude@freebsd.org>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9321
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/92b05f3a18Closes#7333
If you run ./configure --with-config=srpm, it will not trigger
the user m4 scripts to populate the dracut and udev directories.
This causes a build error on Fedora 28. Make the dracut and
udev lines conditional to get around this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7326Closes#7328
Currently, ZFS tracks statistics about calls to arc_read()
via the /proc/spl/kstat/zfs/<pool>/reads file for debugging.
Unfortunately, this file currently counts embedded bps as
disk reads since they are technically processed by the ZIO
layer. This pollutes the log since the ARC will never cache
embedded bps. This patch corrects this issue by preventing
the logging of embedded bp reads.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7334
When given an empty string as a rootds value, bootcfg -C fails with
the error message 'could not set nextboot: '' is an invalid name'.
This should be allowed because it represents clearing the nextboot
configuration.
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9193
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/504645d227Closes#7230
Updated the "Intent Log" section of the "zpool" manual page to
properly reflect the actions that may be performed.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Peter Ashford <ashford@accs.com>
Closes#6938Closes#7318
Resolves importing root pool during boot in dracut. This case was
inadvertently broken with the module autoloading change in #7287.
Reviewed-by: Matthew Thode <prometheanfire@gentoo.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Kash Pande <kash@tripleback.net>
Closes#7322
zfs_dbgmsg() should record a message by default. As a general
principal, these messages shouldn't be too verbose. Furthermore, the
amount of memory used is limited to 4MB (by default).
dprintf() should only record a message if this is a debug build, and
ZFS_DEBUG_DPRINTF is set in zfs_flags. This flag is not set by default
(even on debug builds). These messages are extremely verbose, and
sometimes nontrivial to compute.
SET_ERROR() should only record a message if ZFS_DEBUG_SET_ERROR is set
in zfs_flags. This flag is not set by default (even on debug builds).
This brings our behavior in line with illumos. Note that the message
format is unchanged (including file, line, and function, even though
these are not recorded on illumos).
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#7314
This patch simply corrects some spelling / grammar errors in
the QAT and encryption code comments. No functional changes
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7319
This treats /dev/nvme.. devices the same way as /dev/sd... devices. The
motivation behind this is that whole disk detection did not work on nvme
SSDs without that, because it DKC_UNKNOWN was returned for such devices.
Perhaps there should be a separate DKC_ type for this, but I don't know
enough about the code to know the implications of that.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: timor <timor.dd@googlemail.com>
Closes#7304
This patch adds some comments describing the purpose of "portable"
dnode and objset flags so that it is clear when new flags should
be added to the repective flag masks. This patch includes no
functional changes.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7313
The changes piggyback JSON output support on top of channel programs
(#6558). This way the JSON output support is targeted to scripting
use cases and is easily maintainable since it really only touches
one function (zfs_do_channel_program()).
This patch ports Joyent's JSON nvlist library from illumos to enable
easy JSON printing of channel program output nvlist. To keep the
delta small I also took advantage of the fact that printing in
zfs_do_channel_program() was almost always done before exiting
the program.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#7281
In vdev_queue_aggregate() the zio_execute() bypass should not be
called under the vdev queue lock. This can result in a deadlock
as shown in the stack traces below.
Drop the vdev queue lock then walk the parents of the aggregate IO
to determine the list of component IOs to be bypassed. This can
be done safely without holding the io_lock since the new aggregate
IO has not yet been returned and its parents cannot change.
--- THREAD 1 ---
arc_read()
zio_nowait()
zio_vdev_io_start()
vdev_queue_io() <--- mutex_enter(vq->vq_lock)
vdev_queue_io_to_issue()
vdev_queue_aggregate()
zio_execute()
zio_vdev_io_assess()
zio_wait_for_children() <- mutex_enter(zio->io_lock)
--- THREAD 2 --- (inverse order)
arc_read()
zio_change_priority() <- mutex_enter(zio->zio_lock)
vdev_queue_change_io_priority() <- mutex_enter(vq->vq_lock)
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7307
This patch adds some handling to the QAT acceleration functions
that allows them to handle buffers that are not aligned with the
page cache. At the moment this never happens since callers only
happen to work with page-aligned buffers, but this code should
prevent headaches if this isn't always true in the future. This
patch also adds some cleanups to align the QAT compression code
with the encryption and checksumming code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Weigang Li <weigang.li@intel.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7305
When the pool is suspended, record whether it was due to an I/O error or
due to MMP writes failing to succeed within the required time.
Change spa_suspended from uint8_t to zio_suspend_reason_t to store the
reason.
When userspace queries pool status via spa_tryimport(), report the
reason the pool was suspended in a new key,
ZPOOL_CONFIG_SUSPENDED_REASON.
In libzfs, when interpreting the returned config nvlist, report
suspension due to MMP with a new pool status enum value,
ZPOOL_STATUS_IO_FAILURE_MMP.
In status_callback(), which generates and emits the message when 'zpool
status' is executed, add a case to print an appropriate message for the
new pool status enum value.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7296
This patch enables acceleration of SHA256 checksums using Intel
Quick Assist Technology. This patch also fixes up and refactors
some of the code from QAT encryption to make the behavior
consistent.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chengfeix Zhu <chengfeix.zhu@intel.com>
Signed-off-by: Weigang Li <weigang.li@intel.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7295
ZFS Performance test concurrency should be lowered for better latency
Work by Stephen Blinick.
Nightly performance runs typically consist of two levels of concurrency;
and both are fairly high.
Since the IO runs are to a ZFS filesystem, within a zpool, which is
based on some variable number of vdev's, the amount of IO driven to each
device is variable. Additionally, different device types (HDD vs SSD,
etc) can generally handle a different amount of concurrent IO before
saturating.
Nevertheless, in practice, it appears that most tests are well past the
concurrency saturation point and therefore both perform with the same
throughput, the maximum of the device. Because the queuedepth to the
device(s) is so high however, the latency is much higher than the best
possible at that throughput, and increases linearly with the increase in
concurrency.
This means that changes in code that impact latency during normal
operation (before saturation) may not be apparent when a large component
of the measured latency is from the IO sitting in a queue to be
serviced. Therefore, changing the concurrency settings is recommended
Authored by: Stephen Blinick <stephen.blinick@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: John Wren Kennedy <jwk404@gmail.com>
Ported-by: John Wren Kennedy <jwk404@gmail.com>
OpenZFS-issue: https://www.illumos.org/issues/9076
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/562
Upstream bug: DLPX-45477
Closes#7302
In zfs receive, the function receive_spill should account
for spill block endian conversion as a defensive measure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#7300
With compressed ARC (bug 6950) we use up to 25% of our CPU to decompress
indirect blocks, under a workload of random cached reads. To reduce this
decompression cost, we would like to increase the size of the dbuf cache so
that more indirect blocks can be stored uncompressed.
If we are caching entire large files of recordsize=8K, the indirect blocks
use 1/64th as much memory as the data blocks (assuming they have the same
compression ratio). We suggest making the dbuf cache be 1/32nd of all memory,
so that in this scenario we should be able to keep all the indirect blocks
decompressed in the dbuf cache. (We want it to be more than the 1/64th that
the indirect blocks would use because we need to cache other stuff in the dbuf
cache as well.)
In real world workloads, this won't help as dramatically as the example above,
but we think it's still worth it because the risk of decreasing performance is
low. The potential negative performance impact is that we will be slightly
reducing the size of the ARC (by ~3%).
Porting Notes:
* Added modules options to zfs-module-parameters.5 man page.
* Preserved scaling based on target ARC size rather than max ARC size.
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Prashanth Sreenivasa <pks@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9188
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/564
Upstream bug: DLPX-46942
Closes#7273
Historically a dynamic misc minor number was registered for the
/dev/zfs device in order to prevent minor number collisions. This
was fine but it prevented us from being able to use the kernel
module auto-loaded which requires a known reserved value.
Resolve this issue by adding a configure test to find an available
misc minor number which can then be used in MODULE_ALIAS_MISCDEV at
build time. By adding this alias the zfs kmod is added to the list
of known static-nodes and the systemd-tmpfiles-setup-dev service
will create a /dev/zfs character device at boot time.
This in turn allows us to update the 90-zfs.rules file to make it
aware this is a static node. The upshot of this is that whenever
a process (zpool, zfs, zed) opens the /dev/zfs the kmods will be
automatic loaded. This even works for unprivileged users so there
is no longer a need to manually load the modules at boot time.
As an additional bonus the zed now no longer needs to start after
the zfs-import.service since it will trigger the module load.
In the unlikely event the minor number we selected conflicts with
another out of tree unregistered minor number the code falls back
to dynamically allocating it. In this case the modules again
must be manually loaded.
Note that due to the change in the method of registering the minor
number the zimport.sh test case may incorrectly fail when the
static node for the installed packages is created instead of the
dynamic one. This issue will only transiently impact zimport.sh
for this single commit when we transition and are mixing and
matching methods.
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
TEST_ZIMPORT_SKIP="yes"
Closes#7287
When it's set, a DTL range will be cleared even if its scan/scrub had
errors. This allows to work around resilver/scrub upon import when the
pool has errors.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#7293
Change zfs destroy logic so destroying begins before
the entire list of snapshots is built.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#7271
We hit an illegal memory access in the zrlock trace point. The problem
is that zrl->zr_owner and zrl->zr_caller are assigned locklessly. And if
zrl->zr_owner got assigned a longer string between when __string()
calculate the strlen, and when __assign_str() does strcpy. The copy will
overflow the buffer.
==
For example:
Initial condition:
zrl->zr_owner = A
zrl->zr_caller = "abc"
Thread A Thread B
-------------------------------------------------
if (zrl->zr_owner == A) {
DTRACE_PROBE2() {
__string() {
strlen(zrl->zr_caller) -> 3
allocate buf[4]
}
zrl->zr_owner = B
zrl->zr_caller = "abcd"
__assign_str() {
strcpy(buf, zrl->zr_caller) <- buffer overflow
==
Dereferencing zrl->zr_owner->pid may also be problematic, in that the
zrl->zr_owner got changed to other task, and that task exits, freeing
the task_struct. This should be very unlikely, as the other task need to
zrl_remove and exit between the dereferencing zr->zr_owner and
zr->zr_owner->pid. Nevertheless, we'll deal with it as well.
To fix the zrl->zr_caller issue, instead of copy the string content, we
just copy the pointer, this is safe because it always points to
__func__, which is static. As for the zrl->zr_owner issue, we pass in
curthread instead of using zrl->zr_owner.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#7291
When a single pool contains more vdevs than the CONFIG_HZ for
for the kernel the mmp thread will not delay properly. Switch
to using cv_timedwait_sig_hires() to handle higher resolution
delays.
This issue was reported on Arch Linux where HZ defaults to only
100 and this could be fairly easily reproduced with a reasonably
large pool. Most distribution kernels set CONFIG_HZ=250 or
CONFIG_HZ=1000 and thus are unlikely to be impacted.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7205Closes#7289
A config lock should be held while vdev_count_leaves() walks the tree,
otherwise the pointers reference may become invalid during the walk.
SCL_VDEV is a minimal lock provided for such uses cases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7286
When multihost is disabled on a pool, and the pool is resumed via zpool
clear, within a single cycle of the mmp thread's loop (e.g. while it's
in the cv_timedwait call), both mmp_last_write and mmp_delay should be
updated.
The original code mistakenly treated the two cases as if they could not
occur at the same time.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7286
PR #7208 was a patch to allow non-reserved pool names which begin with
mirror, raidz, spare (but do not equal), however we'd rather document
it in the man page for compatibility with other OpenZFS implementations,
to avoid pool names that may not work on non-Linux platforms.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#7216
With rpm-software-management/rpm@5e94633 a package version containing
invalid characters (most commonly a double '-') causes the kmod package
generation to terminate with an error. This change takes advantage of
the newly introduced rpm macro "_wrong_version_format_terminate_build"
to allow kmod packages to be built.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7284
With rpm-software-management/rpm@5e94633 a package version containing
invalid characters (most commonly a double '-') causes the kmod package
generation to terminate with an error. This change takes advantage of
the newly introduced rpm macro "_wrong_version_format_terminate_build"
to allow kmod packages to be built.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#691
get_format_prompt_string() and zpool_state_to_name() return
a string literal which is read-only, thus they should return
`const char*`.
zpool_get_prop_string() returns a non-const string after
successful nv-lookup, and returns a string literal otherwise.
Since this function is designed to be used for read-only purpose,
the return type should also be `const char*`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#7285
This patch adds support for acceleration of AES-GCM encryption
with Intel Quick Assist Technology.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chengfeix Zhu <chengfeix.zhu@intel.com>
Signed-off-by: Weigang Li <weigang.li@intel.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7282
Due to zpool create auto-partioning in Linux (i.e. sdb1),
certain utilities need to use the parition (sdb1) while
others use the whole disk name (sdb).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#6939Closes#7261
Change file related checks to use user namespaces and make
sure involved uids/gids are mappable in the current
namespace.
Note that checks without file ownership information will
still not take user namespaces into account, as some of
these should be handled via 'zfs allow' (otherwise root in a
user namespace could issue commands such as `zpool export`).
This also adds an initial user namespace regression test
for the setgid bit loss, with a user_ns_exec helper usable
in further tests.
Additionally, configure checks for the required user
namespace related features are added for:
* ns_capable
* kuid/kgid_has_mapping()
* user_ns in cred_t
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Closes#6800Closes#7270
The test could fail when attempting to write to a newly created
volume which was missing its device node. Resolve the issue by
calling block_device_wait() which blocks until udev creates the
needed entry.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7276Closes#7277
Implement a new helper within_tolerance to test if a value
is within range of a target.
Because the dbufstats and dbufs kstat file are being read
at slightly different times, it is possible for stats to be
slightly off. Use within_tolerance to determine if the value
is "close enough" to the target.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#7239Closes#7266
Some usage patterns like send/recv of replication streams can
produce a large number of events. In such a case, the current
all-syslog.sh zedlet will hold up to its name, and flood the
logs with mostly redundant information. Two mitigate this
situation, this changeset introduces to new variables
ZED_SYSLOG_SUBCLASS_INCLUDE and ZED_SYSLOG_SUBCLASS_EXCLUDE
to zed.rc that give more control over which event classes end
up in the syslog.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Daniel Kobras <d.kobras@science-computing.de>
Closes#6886Closes#7260
Once per pass through the MMP thread's loop, the vdev tree is walked to
find a suitable leaf to write the next MMP block to. If no such leaf is
found, the thread sleeps for a while and resumes at the top of the loop.
Add an entry to multihost_history when no leaf can be found, and record
the reason in the error column. The error code for such entries is a
bitfield, displayed in hex:
0x1 At least one vdev (interior or leaf) was not writeable.
0x2 At least one writeable leaf vdev was found, but it had a pending
MMP write.
timestamp = the time in seconds since the epoch when no leaf could be
found originally.
duration = the time (in ns) during which no MMP block was written for
this reason. This does not include the preceeding inter-write period
nor the following inter-write period.
vdev_guid = the number of sequential cycles of the MMP thread looop when
this occurred.
Sample output, truncated to fit:
For records of skipped MMP writes the right-most column, vdev_path, is
reported as "-".
id txg timestamp error duration mmp_delay vdev_guid ...
936 11 1520036441 0 146264 891422313 1740883117838 ...
937 11 1520036441 0 163956 888356657 7320395061548 ...
938 11 1520036442 0 130690 885314969 7320395061548 ...
939 11 1520036442 0 2001068577 882296582 1740883117838 ...
940 11 1520036443 0 161806 882296582 7320395061548 ...
941 11 1520036443 0x2 0 998020546 1 ...
942 11 1520036444 0 136585 998020546 7320395061548 ...
943 11 1520036444 0x2 0 998020257 1 ...
944 11 1520036445 5 2002662964 994160219 1740883117838 ...
945 11 1520036445 0x2 998073118 994160219 3 ...
946 11 1520036447 0 247136 994160219 7320395061548 ...
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7212
If something holds the config lock as a writer for too long, MMP will
fail to issue MMP writes in a timely manner. This will result either in
the pool being suspended, or in an extreme case, in the pool not being
protected.
If the time to acquire the config lock exceeds 1/10 of the minimum
zfs_multihost_interval, report it in the zfs debug log.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7212
Datasets can be busy when calling zfs destroy. Introduce
a helper function to destroy datasets and use it to destroy
datasets in zfs_allow_004_pos, zfs_promote_008_pos, and
zfs_destroy_002_pos.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#7224Closes#7246Closes#7249Closes#7267
1) The Coverity Scan reports some issues for the project
quota patch, including:
1.1) zfs_prop_get_userquota() directly uses the const quota
type value as the condition check by wrong.
1.2) dmu_objset_userquota_get_ids() may cause dnode::dn_newgid
to be overwritten by dnode::dn->dn_oldprojid.
2) This patch fixes related issues. It also enhances the logic
for zfs_project_item_alloc() to avoid buffer overflow.
3) Skip project quota ability check if does not change project
quota related things (id or flag). Otherwise, it will cause
chattr (for other non project quota flags) operation failed
if project quota disabled.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fan Yong <fan.yong@intel.com>
Closes#7251Closes#7265
As of https://github.com/torvalds/linux/commit/fb6d47a, get_disk()
is now get_disk_and_module(). Add a configure check to determine
if we need to use get_disk_and_module().
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#7264
Change checksum & IO delay ratelimit thresholds from 5/sec to 20/sec.
This allows zed to actually trigger if a bunch of these events arrive in
a short period of time (zed has a threshold of 10 events in 10 sec).
Previously, if you had, say, 100 checksum errors in 1 sec, it would get
ratelimited to 5/sec which wouldn't trigger zed to fault the drive.
Also, convert the checksum and IO delay thresholds to module params for
easy testing.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7252
In zil_lwb_commit() with TX_WRITE, we copy the log write record (lrw)
into the log write block (lwb) and send it off using zil_lwb_add_txg().
If we also have WR_NEED_COPY, we additionally copy the lwr's data into
the lwb to be sent off. If the lwr + data doesn't fit into the lwb, we
send the lrw and as much data as will fit (dnow bytes), then go back
and do the same with the remaining data.
Each time through this loop we're sending dnow data bytes. I.e.
zil_itx_needcopy_bytes should be incremented by dnow.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Closes#6988Closes#7176
