mirror of
https://git.proxmox.com/git/mirror_zfs.git
synced 2024-11-17 18:11:00 +03:00
28c91ab66d
165 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Paul Dagnelie
|
dc04a8c757 |
Prevent race in blkptr_verify against device removal
When we check the vdev of the blkptr in zfs_blkptr_verify, we can run into a race condition where that vdev is temporarily unavailable. This happens when a device removal operation and the old vdev_t has been removed from the array, but the new indirect vdev has not yet been inserted. We hold the spa_config_lock while doing our sensitive verification. To ensure that we don't deadlock, we only grab the lock if we don't have config_writer held. In addition, I had to const the tags of the refcounts and the spa_config_lock arguments. Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com> Signed-off-by: Paul Dagnelie <pcd@delphix.com> Closes #9112 |
||
|
Serapheim Dimitropoulos
|
93e28d661e |
Log Spacemap Project
= Motivation At Delphix we've seen a lot of customer systems where fragmentation is over 75% and random writes take a performance hit because a lot of time is spend on I/Os that update on-disk space accounting metadata. Specifically, we seen cases where 20% to 40% of sync time is spend after sync pass 1 and ~30% of the I/Os on the system is spent updating spacemaps. The problem is that these pools have existed long enough that we've touched almost every metaslab at least once, and random writes scatter frees across all metaslabs every TXG, thus appending to their spacemaps and resulting in many I/Os. To give an example, assuming that every VDEV has 200 metaslabs and our writes fit within a single spacemap block (generally 4K) we have 200 I/Os. Then if we assume 2 levels of indirection, we need 400 additional I/Os and since we are talking about metadata for which we keep 2 extra copies for redundancy we need to triple that number, leading to a total of 1800 I/Os per VDEV every TXG. We could try and decrease the number of metaslabs so we have less I/Os per TXG but then each metaslab would cover a wider range on disk and thus would take more time to be loaded in memory from disk. In addition, after it's loaded, it's range tree would consume more memory. Another idea would be to just increase the spacemap block size which would allow us to fit more entries within an I/O block resulting in fewer I/Os per metaslab and a speedup in loading time. The problem is still that we don't deal with the number of I/Os going up as the number of metaslabs is increasing and the fact is that we generally write a lot to a few metaslabs and a little to the rest of them. Thus, just increasing the block size would actually waste bandwidth because we won't be utilizing our bigger block size. = About this patch This patch introduces the Log Spacemap project which provides the solution to the above problem while taking into account all the aforementioned tradeoffs. The details on how it achieves that can be found in the references sections below and in the code (see Big Theory Statement in spa_log_spacemap.c). Even though the change is fairly constraint within the metaslab and lower-level SPA codepaths, there is a side-change that is user-facing. The change is that VDEV IDs from VDEV holes will no longer be reused. To give some background and reasoning for this, when a log device is removed and its VDEV structure was replaced with a hole (or was compacted; if at the end of the vdev array), its vdev_id could be reused by devices added after that. Now with the pool-wide space maps recording the vdev ID, this behavior can cause problems (e.g. is this entry referring to a segment in the new vdev or the removed log?). Thus, to simplify things the ID reuse behavior is gone and now vdev IDs for top-level vdevs are truly unique within a pool. = Testing The illumos implementation of this feature has been used internally for a year and has been in production for ~6 months. For this patch specifically there don't seem to be any regressions introduced to ZTS and I have been running zloop for a week without any related problems. = Performance Analysis (Linux Specific) All performance results and analysis for illumos can be found in the links of the references. Redoing the same experiments in Linux gave similar results. Below are the specifics of the Linux run. After the pool reached stable state the percentage of the time spent in pass 1 per TXG was 64% on average for the stock bits while the log spacemap bits stayed at 95% during the experiment (graph: sdimitro.github.io/img/linux-lsm/PercOfSyncInPassOne.png). Sync times per TXG were 37.6 seconds on average for the stock bits and 22.7 seconds for the log spacemap bits (related graph: sdimitro.github.io/img/linux-lsm/SyncTimePerTXG.png). As a result the log spacemap bits were able to push more TXGs, which is also the reason why all graphs quantified per TXG have more entries for the log spacemap bits. Another interesting aspect in terms of txg syncs is that the stock bits had 22% of their TXGs reach sync pass 7, 55% reach sync pass 8, and 20% reach 9. The log space map bits reached sync pass 4 in 79% of their TXGs, sync pass 7 in 19%, and sync pass 8 at 1%. This emphasizes the fact that not only we spend less time on metadata but we also iterate less times to convergence in spa_sync() dirtying objects. [related graphs: stock- sdimitro.github.io/img/linux-lsm/NumberOfPassesPerTXGStock.png lsm- sdimitro.github.io/img/linux-lsm/NumberOfPassesPerTXGLSM.png] Finally, the improvement in IOPs that the userland gains from the change is approximately 40%. There is a consistent win in IOPS as you can see from the graphs below but the absolute amount of improvement that the log spacemap gives varies within each minute interval. sdimitro.github.io/img/linux-lsm/StockVsLog3Days.png sdimitro.github.io/img/linux-lsm/StockVsLog10Hours.png = Porting to Other Platforms For people that want to port this commit to other platforms below is a list of ZoL commits that this patch depends on: Make zdb results for checkpoint tests consistent |
||
|
George Wilson
|
681a85cb01 |
nopwrites on dmu_sync-ed blocks can result in a panic
After device removal, performing nopwrites on a dmu_sync-ed block will result in a panic. This panic can show up in two ways: 1. an attempt to issue an IOCTL in vdev_indirect_io_start() 2. a failed comparison of zio->io_bp and zio->io_bp_orig in zio_done() To resolve both of these panics, nopwrites of blocks on indirect vdevs should be ignored and new allocations should be performed on concrete vdevs. Reviewed-by: Igor Kozhukhov <igor@dilos.org> Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: Don Brady <don.brady@delphix.com> Signed-off-by: George Wilson <gwilson@delphix.com> Closes #8957 |
||
|
loli10K
|
746d4a451e |
Fix bp_embedded_type enum definition
With the addition of BP_EMBEDDED_TYPE_REDACTED in
|
||
|
Matthew Ahrens
|
accd6d9dc4 |
dedup=verify doesn't clear the blkptr's dedup flag
The logic to handle strong checksum collisions where the data doesn't match is incorrect. It is not clearing the dedup bit of the blkptr, which can cause a panic later in zio_ddt_free() due to the dedup table not matching what is in the blkptr. Reviewed-by: Tom Caputi <tcaputi@datto.com> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Matthew Ahrens <mahrens@delphix.com> External-issue: DLPX-48097 Closes #8936 |
||
|
Matthew Ahrens
|
050d720c43 |
Remove dedupditto functionality
If dedup is in use, the `dedupditto` property can be set, causing ZFS to keep an extra copy of data that is referenced many times (>100x). The idea was that this data is more important than other data and thus we want to be really sure that it is not lost if the disk experiences a small amount of random corruption. ZFS (and system administrators) rely on the pool-level redundancy to protect their data (e.g. mirroring or RAIDZ). Since the user/sysadmin doesn't have control over what data will be offered extra redundancy by dedupditto, this extra redundancy is not very useful. The bulk of the data is still vulnerable to loss based on the pool-level redundancy. For example, if particle strikes corrupt 0.1% of blocks, you will either be saved by mirror/raidz, or you will be sad. This is true even if dedupditto saved another 0.01% of blocks from being corrupted. Therefore, the dedupditto functionality is rarely enabled (i.e. the property is rarely set), and it fulfills its promise of increased redundancy even more rarely. Additionally, this feature does not work as advertised (on existing releases), because scrub/resilver did not repair the extra (dedupditto) copy (see https://github.com/zfsonlinux/zfs/pull/8270). In summary, this seldom-used feature doesn't work, and even if it did it wouldn't provide useful data protection. It has a non-trivial maintenance burden (again see https://github.com/zfsonlinux/zfs/pull/8270). We should remove the dedupditto functionality. For backwards compatibility with the existing CLI, "zpool set dedupditto" will still "succeed" (exit code zero), but won't have any effect. For backwards compatibility with existing pools that had dedupditto enabled at some point, the code will still be able to understand dedupditto blocks and free them when appropriate. However, ZFS won't write any new dedupditto blocks. Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: Igor Kozhukhov <igor@dilos.org> Reviewed-by: Alek Pinchuk <apinchuk@datto.com> Issue #8270 Closes #8310 |
||
|
Paul Dagnelie
|
30af21b025 |
Implement Redacted Send/Receive
Redacted send/receive allows users to send subsets of their data to a target system. One possible use case for this feature is to not transmit sensitive information to a data warehousing, test/dev, or analytics environment. Another is to save space by not replicating unimportant data within a given dataset, for example in backup tools like zrepl. Redacted send/receive is a three-stage process. First, a clone (or clones) is made of the snapshot to be sent to the target. In this clone (or clones), all unnecessary or unwanted data is removed or modified. This clone is then snapshotted to create the "redaction snapshot" (or snapshots). Second, the new zfs redact command is used to create a redaction bookmark. The redaction bookmark stores the list of blocks in a snapshot that were modified by the redaction snapshot(s). Finally, the redaction bookmark is passed as a parameter to zfs send. When sending to the snapshot that was redacted, the redaction bookmark is used to filter out blocks that contain sensitive or unwanted information, and those blocks are not included in the send stream. When sending from the redaction bookmark, the blocks it contains are considered as candidate blocks in addition to those blocks in the destination snapshot that were modified since the creation_txg of the redaction bookmark. This step is necessary to allow the target to rehydrate data in the case where some blocks are accidentally or unnecessarily modified in the redaction snapshot. The changes to bookmarks to enable fast space estimation involve adding deadlists to bookmarks. There is also logic to manage the life cycles of these deadlists. The new size estimation process operates in cases where previously an accurate estimate could not be provided. In those cases, a send is performed where no data blocks are read, reducing the runtime significantly and providing a byte-accurate size estimate. Reviewed-by: Dan Kimmel <dan.kimmel@delphix.com> Reviewed-by: Matt Ahrens <mahrens@delphix.com> Reviewed-by: Prashanth Sreenivasa <pks@delphix.com> Reviewed-by: John Kennedy <john.kennedy@delphix.com> Reviewed-by: George Wilson <george.wilson@delphix.com> Reviewed-by: Chris Williamson <chris.williamson@delphix.com> Reviewed-by: Pavel Zhakarov <pavel.zakharov@delphix.com> Reviewed-by: Sebastien Roy <sebastien.roy@delphix.com> Reviewed-by: Prakash Surya <prakash.surya@delphix.com> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Paul Dagnelie <pcd@delphix.com> Closes #7958 |
||
|
Matthew Ahrens
|
be89734a29 |
compress metadata in later sync passes
Starting in sync pass 5 (zfs_sync_pass_dont_compress), we disable compression (including of metadata). Ostensibly this helps the sync passes to converge (i.e. for a sync pass to not need to allocate anything because it is 100% overwrites). However, in practice it increases the average number of sync passes, because when we turn compression off, a lot of block's size will change and thus we have to re-allocate (not overwrite) them. It also increases the number of 128KB allocations (e.g. for indirect blocks and spacemaps) because these will not be compressed. The 128K allocations are especially detrimental to performance on highly fragmented systems, which may have very few free segments of this size, and may need to load new metaslabs to satisfy 128K allocations. We should increase zfs_sync_pass_dont_compress. In practice on a highly fragmented system we see a few 5-pass txg's, a tiny number of 6-pass txg's, and no txg's with more than 6 passes. Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com> Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com> Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com> Reviewed-by: George Wilson <george.wilson@delphix.com> Signed-off-by: Matthew Ahrens <mahrens@delphix.com> External-issue: DLPX-63431 Closes #8892 |
||
|
Matthew Ahrens
|
5662fd5794 |
single-chunk scatter ABDs can be treated as linear
Scatter ABD's are allocated from a number of pages. In contrast to
linear ABD's, these pages are disjoint in the kernel's virtual address
space, so they can't be accessed as a contiguous buffer. Therefore
routines that need a linear buffer (e.g. abd_borrow_buf() and friends)
must allocate a separate linear buffer (with zio_buf_alloc()), and copy
the contents of the pages to/from the linear buffer. This can have a
measurable performance overhead on some workloads.
https://github.com/zfsonlinux/zfs/commit/87c25d567fb7969b44c7d8af63990e
("abd_alloc should use scatter for >1K allocations") increased the use
of scatter ABD's, specifically switching 1.5K through 4K (inclusive)
buffers from linear to scatter. For workloads that access blocks whose
compressed sizes are in this range, that commit introduced an additional
copy into the read code path. For example, the
sequential_reads_arc_cached tests in the test suite were reduced by
around 5% (this is doing reads of 8K-logical blocks, compressed to 3K,
which are cached in the ARC).
This commit treats single-chunk scattered buffers as linear buffers,
because they are contiguous in the kernel's virtual address space.
All single-page (4K) ABD's can be represented this way. Some multi-page
ABD's can also be represented this way, if we were able to allocate a
single "chunk" (higher-order "page" which represents a power-of-2 series
of physically-contiguous pages). This is often the case for 2-page (8K)
ABD's.
Representing a single-entry scatter ABD as a linear ABD has the
performance advantage of avoiding the copy (and allocation) in
abd_borrow_buf_copy / abd_return_buf_copy. A performance increase of
around 5% has been observed for ARC-cached reads (of small blocks which
can take advantage of this), fixing the regression introduced by
|
||
|
Sara Hartse
|
a887d653b3 |
Restrict kstats and print real pointers
There are several places where we use zfs_dbgmsg and %p to print pointers. In the Linux kernel, these values obfuscated to prevent information leaks which means the pointers aren't very useful for debugging crash dumps. We decided to restrict the permissions of dbgmsg (and some other kstats while we were at it) and print pointers with %px in zfs_dbgmsg as well as spl_dumpstack Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: John Gallagher <john.gallagher@delphix.com> Signed-off-by: sara hartse <sara.hartse@delphix.com> Closes #8467 Closes #8476 |
||
|
Brian Behlendorf
|
1b939560be
|
Add TRIM support
UNMAP/TRIM support is a frequently-requested feature to help prevent performance from degrading on SSDs and on various other SAN-like storage back-ends. By issuing UNMAP/TRIM commands for sectors which are no longer allocated the underlying device can often more efficiently manage itself. This TRIM implementation is modeled on the `zpool initialize` feature which writes a pattern to all unallocated space in the pool. The new `zpool trim` command uses the same vdev_xlate() code to calculate what sectors are unallocated, the same per- vdev TRIM thread model and locking, and the same basic CLI for a consistent user experience. The core difference is that instead of writing a pattern it will issue UNMAP/TRIM commands for those extents. The zio pipeline was updated to accommodate this by adding a new ZIO_TYPE_TRIM type and associated spa taskq. This new type makes is straight forward to add the platform specific TRIM/UNMAP calls to vdev_disk.c and vdev_file.c. These new ZIO_TYPE_TRIM zios are handled largely the same way as ZIO_TYPE_READs or ZIO_TYPE_WRITEs. This makes it possible to largely avoid changing the pipieline, one exception is that TRIM zio's may exceed the 16M block size limit since they contain no data. In addition to the manual `zpool trim` command, a background automatic TRIM was added and is controlled by the 'autotrim' property. It relies on the exact same infrastructure as the manual TRIM. However, instead of relying on the extents in a metaslab's ms_allocatable range tree, a ms_trim tree is kept per metaslab. When 'autotrim=on', ranges added back to the ms_allocatable tree are also added to the ms_free tree. The ms_free tree is then periodically consumed by an autotrim thread which systematically walks a top level vdev's metaslabs. Since the automatic TRIM will skip ranges it considers too small there is value in occasionally running a full `zpool trim`. This may occur when the freed blocks are small and not enough time was allowed to aggregate them. An automatic TRIM and a manual `zpool trim` may be run concurrently, in which case the automatic TRIM will yield to the manual TRIM. Reviewed-by: Jorgen Lundman <lundman@lundman.net> Reviewed-by: Tim Chase <tim@chase2k.com> Reviewed-by: Matt Ahrens <mahrens@delphix.com> Reviewed-by: George Wilson <george.wilson@delphix.com> Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com> Contributions-by: Saso Kiselkov <saso.kiselkov@nexenta.com> Contributions-by: Tim Chase <tim@chase2k.com> Contributions-by: Chunwei Chen <tuxoko@gmail.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Closes #8419 Closes #598 |
||
|
Tony Hutter
|
2bbec1c910 |
Make zpool status counters match error events count
The number of IO and checksum events should match the number of errors seen in zpool status. Previously there was a mismatch between the two counts because zpool status would only count unrecovered errors, while zpool events would get an event for *all* errors (recovered or not). This lead to situations where disks could be faulted for "too many errors", while at the same time showing zero errors in zpool status. This fixes the zpool status error counters to increment at the same times we post the error events. Reviewed-by: Tom Caputi <tcaputi@datto.com> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: Olaf Faaland <faaland1@llnl.gov> Signed-off-by: Tony Hutter <hutter2@llnl.gov> Closes #4851 Closes #7817 |
||
|
Sara Hartse
|
f545b6ae00 |
Delay injection can cause indefinitely hung zios
If we hit the (NSEC_TO_TICK(diff) == 0) condition in zio_delay_interrupt, zio_interrupt is never called and the zio does not progress. Reviewed by: Matt Ahrens <mahrens@delphix.com> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: George Melikov <mail@gmelikov.ru> Signed-off-by: sara hartse <sara.hartse@delphix.com> Closes #8404 |
||
|
Tim Chase
|
638dd5f44e |
zio_deadman_impl() fix and enhancement
Add the zio_deadman_log_all tunable to print all zios in zio_deadman_impl(). Also, in all cases, display the depth of the zio relative to the original parent zio. This is meant to be used by developers to gain diagnostic information for hangs which don't involve fully set-up zio trees or are otherwise stuck or hung in an early stage. Reviewed-by: Olaf Faaland <faaland1@llnl.gov> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: loli10K <ezomori.nozomu@gmail.com> Signed-off-by: Tim Chase <tim@chase2k.com> Closes #8362 |
||
|
Brian Behlendorf
|
d611989fdc
|
Minor spelling corrections
Some minor spelling mistakes and typos. No functional changes. Reviewed-by: Neal Gompa <ngompa@datto.com> Reviewed by: Matt Ahrens <mahrens@delphix.com> Reviewed-by: Giuseppe Di Natale <guss80@gmail.com> Reviewed-by: bunder2015 <omfgbunder@gmail.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Closes #8272 |
||
|
George Wilson
|
18b14b17c8 |
OpenZFS 9993 - zil writes can get delayed in zio pipeline
Authored by: George Wilson <george.wilson@delphix.com> Reviewed by: Prakash Surya <prakash.surya@delphix.com> Reviewed by: Brad Lewis <brad.lewis@delphix.com> Reviewed by: Matt Ahrens <matt@delphix.com> Reviewed by: Tom Caputi <tcaputi@datto.com> Reviewed by: George Melikov <mail@gmelikov.ru> Approved by: Dan McDonald <danmcd@joyent.com> Ported-by: Brian Behlendorf <behlendorf1@llnl.gov> OpenZFS-issue: https://www.illumos.org/issues/9993 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/2258ad0b Closes #8185 |
||
|
Tony Hutter
|
ad796b8a3b |
Add zpool status -s (slow I/Os) and -p (parseable)
This patch adds a new slow I/Os (-s) column to zpool status to show the number of VDEV slow I/Os. This is the number of I/Os that didn't complete in zio_slow_io_ms milliseconds. It also adds a new parsable (-p) flag to display exact values. NAME STATE READ WRITE CKSUM SLOW testpool ONLINE 0 0 0 - mirror-0 ONLINE 0 0 0 - loop0 ONLINE 0 0 0 20 loop1 ONLINE 0 0 0 0 Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed by: Matthew Ahrens <mahrens@delphix.com> Signed-off-by: Tony Hutter <hutter2@llnl.gov> Closes #7756 Closes #6885 |
||
|
Brad Lewis
|
c955398b52 |
OpenZFS 9677 - panic from zio_write_gang_block()
Panic from zio_write_gang_block() when creating dump device on fragmented rpool. Authored by: Brad Lewis <brad.lewis@delphix.com> Reviewed by: Matt Ahrens <matt@delphix.com> Reviewed by: George Wilson <george.wilson@delphix.com> Reviewed by: Prashanth Sreenivasa <pks@delphix.com> Approved by: Robert Mustacchi <rm@joyent.com> Ported-by: Behlendorf <behlendorf1@llnl.gov> OpenZFS-issue: https://illumos.org/issues/9677 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7341a7d Closes #7975 |
||
|
Tim Schumacher
|
424fd7c3e0 |
Prefix all refcount functions with zfs_
Recent changes in the Linux kernel made it necessary to prefix the refcount_add() function with zfs_ due to a name collision. To bring the other functions in line with that and to avoid future collisions, prefix the other refcount functions as well. Reviewed by: Matthew Ahrens <mahrens@delphix.com> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Tim Schumacher <timschumi@gmx.de> Closes #7963 |
||
|
Don Brady
|
cc99f275a2 |
Pool allocation classes
Allocation Classes add the ability to have allocation classes in a pool that are dedicated to serving specific block categories, such as DDT data, metadata, and small file blocks. A pool can opt-in to this feature by adding a 'special' or 'dedup' top-level VDEV. Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com> Reviewed-by: Richard Laager <rlaager@wiktel.com> Reviewed-by: Alek Pinchuk <apinchuk@datto.com> Reviewed-by: Håkan Johansson <f96hajo@chalmers.se> Reviewed-by: Andreas Dilger <andreas.dilger@chamcloud.com> Reviewed-by: DHE <git@dehacked.net> Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com> Reviewed-by: Gregor Kopka <gregor@kopka.net> Reviewed-by: Kash Pande <kash@tripleback.net> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: Matthew Ahrens <mahrens@delphix.com> Signed-off-by: Don Brady <don.brady@delphix.com> Closes #5182 |
||
|
Tom Caputi
|
c3bd3fb4ac |
OpenZFS 9403 - assertion failed in arc_buf_destroy()
Assertion failed in arc_buf_destroy() when concurrently reading block with checksum error. Porting notes: * The ability to zinject decompression errors has been added, but this only works at the zio_decompress() level, where we have all of the info we need to match against the user's zinject options. * The decompress_fault test has been added to test the new zinject functionality * We attempted to set zio_decompress_fail_fraction to (1 << 18) in ztest for further test coverage. Although this did uncover a few low priority issues, this unfortuantely also causes ztest to ASSERT in many locations where the code is working correctly since it is designed to fail on IO errors. Developers can manually set this variable with the '-o' option to find and debug issues. Authored by: Matt Ahrens <mahrens@delphix.com> Reviewed by: George Wilson <george.wilson@delphix.com> Reviewed by: Paul Dagnelie <pcd@delphix.com> Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com> Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov> Approved by: Matt Ahrens <mahrens@delphix.com> Ported-by: Tom Caputi <tcaputi@datto.com> OpenZFS-issue: https://illumos.org/issues/9403 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/fa98e487a9 Closes #7822 |
||
|
Matthew Ahrens
|
62840030a7 |
Reduce taskq and context-switch cost of zio pipe
When doing a read from disk, ZFS creates 3 ZIO's: a zio_null(), the logical zio_read(), and then a physical zio. Currently, each of these results in a separate taskq_dispatch(zio_execute). On high-read-iops workloads, this causes a significant performance impact. By processing all 3 ZIO's in a single taskq entry, we reduce the overhead on taskq locking and context switching. We accomplish this by allowing zio_done() to return a "next zio to execute" to zio_execute(). This results in a ~12% performance increase for random reads, from 96,000 iops to 108,000 iops (with recordsize=8k, on SSD's). Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed by: George Wilson <george.wilson@delphix.com> Signed-off-by: Matthew Ahrens <mahrens@delphix.com> External-issue: DLPX-59292 Closes #7736 |
||
|
Paul Dagnelie
|
492f64e941 |
OpenZFS 9112 - Improve allocation performance on high-end systems
Overview ======== We parallelize the allocation process by creating the concept of "allocators". There are a certain number of allocators per metaslab group, defined by the value of a tunable at pool open time. Each allocator for a given metaslab group has up to 2 active metaslabs; one "primary", and one "secondary". The primary and secondary weight mean the same thing they did in in the pre-allocator world; primary metaslabs are used for most allocations, secondary metaslabs are used for ditto blocks being allocated in the same metaslab group. There is also the CLAIM weight, which has been separated out from the other weights, but that is less important to understanding the patch. The active metaslabs for each allocator are moved from their normal place in the metaslab tree for the group to the back of the tree. This way, they will not be selected for use by other allocators searching for new metaslabs unless all the passive metaslabs are unsuitable for allocations. If that does happen, the allocators will "steal" from each other to ensure that IOs don't fail until there is truly no space left to perform allocations. In addition, the alloc queue for each metaslab group has been broken into a separate queue for each allocator. We don't want to dramatically increase the number of inflight IOs on low-end systems, because it can significantly increase txg times. On the other hand, we want to ensure that there are enough IOs for each allocator to allow for good coalescing before sending the IOs to the disk. As a result, we take a compromise path; each allocator's alloc queue max depth starts at a certain value for every txg. Every time an IO completes, we increase the max depth. This should hopefully provide a good balance between the two failure modes, while not dramatically increasing complexity. We also parallelize the spa_alloc_tree and spa_alloc_lock, which cause very similar contention when selecting IOs to allocate. This parallelization uses the same allocator scheme as metaslab selection. Performance Results =================== Performance improvements from this change can vary significantly based on the number of CPUs in the system, whether or not the system has a NUMA architecture, the speed of the drives, the values for the various tunables, and the workload being performed. For an fio async sequential write workload on a 24 core NUMA system with 256 GB of RAM and 8 128 GB SSDs, there is a roughly 25% performance improvement. Future Work =========== Analysis of the performance of the system with this patch applied shows that a significant new bottleneck is the vdev disk queues, which also need to be parallelized. Prototyping of this change has occurred, and there was a performance improvement, but more work needs to be done before its stability has been verified and it is ready to be upstreamed. Authored by: Paul Dagnelie <pcd@delphix.com> Reviewed by: Matthew Ahrens <mahrens@delphix.com> Reviewed by: George Wilson <george.wilson@delphix.com> Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com> Reviewed by: Alexander Motin <mav@FreeBSD.org> Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov> Approved by: Gordon Ross <gwr@nexenta.com> Ported-by: Paul Dagnelie <pcd@delphix.com> Signed-off-by: Paul Dagnelie <pcd@delphix.com> Porting Notes: * Fix reservation test failures by increasing tolerance. OpenZFS-issue: https://illumos.org/issues/9112 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3f3cc3c3 Closes #7682 |
||
|
Serapheim Dimitropoulos
|
d2734cce68 |
OpenZFS 9166 - zfs storage pool checkpoint
Details about the motivation of this feature and its usage can
be found in this blogpost:
https://sdimitro.github.io/post/zpool-checkpoint/
A lightning talk of this feature can be found here:
https://www.youtube.com/watch?v=fPQA8K40jAM
Implementation details can be found in big block comment of
spa_checkpoint.c
Side-changes that are relevant to this commit but not explained
elsewhere:
* renames members of "struct metaslab trees to be shorter without
losing meaning
* space_map_{alloc,truncate}() accept a block size as a
parameter. The reason is that in the current state all space
maps that we allocate through the DMU use a global tunable
(space_map_blksz) which defauls to 4KB. This is ok for metaslab
space maps in terms of bandwirdth since they are scattered all
over the disk. But for other space maps this default is probably
not what we want. Examples are device removal's vdev_obsolete_sm
or vdev_chedkpoint_sm from this review. Both of these have a
1:1 relationship with each vdev and could benefit from a bigger
block size.
Porting notes:
* The part of dsl_scan_sync() which handles async destroys has
been moved into the new dsl_process_async_destroys() function.
* Remove "VERIFY(!(flags & FWRITE))" in "kernel.c" so zhack can write
to block device backed pools.
* ZTS:
* Fix get_txg() in zpool_sync_001_pos due to "checkpoint_txg".
* Don't use large dd block sizes on /dev/urandom under Linux in
checkpoint_capacity.
* Adopt Delphix-OS's setting of 4 (spa_asize_inflation =
SPA_DVAS_PER_BP + 1) for the checkpoint_capacity test to speed
its attempts to fill the pool
* Create the base and nested pools with sync=disabled to speed up
the "setup" phase.
* Clear labels in test pool between checkpoint tests to avoid
duplicate pool issues.
* The import_rewind_device_replaced test has been marked as "known
to fail" for the reasons listed in its DISCLAIMER.
* New module parameters:
zfs_spa_discard_memory_limit,
zfs_remove_max_bytes_pause (not documented - debugging only)
vdev_max_ms_count (formerly metaslabs_per_vdev)
vdev_min_ms_count
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9166
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7159fdb8
Closes #7570
|
||
|
Brian Behlendorf
|
93ce2b4ca5 |
Update build system and packaging
Minimal changes required to integrate the SPL sources in to the
ZFS repository build infrastructure and packaging.
Build system and packaging:
* Renamed SPL_* autoconf m4 macros to ZFS_*.
* Removed redundant SPL_* autoconf m4 macros.
* Updated the RPM spec files to remove SPL package dependency.
* The zfs package obsoletes the spl package, and the zfs-kmod
package obsoletes the spl-kmod package.
* The zfs-kmod-devel* packages were updated to add compatibility
symlinks under /usr/src/spl-x.y.z until all dependent packages
can be updated. They will be removed in a future release.
* Updated copy-builtin script for in-kernel builds.
* Updated DKMS package to include the spl.ko.
* Updated stale AUTHORS file to include all contributors.
* Updated stale COPYRIGHT and included the SPL as an exception.
* Renamed README.markdown to README.md
* Renamed OPENSOLARIS.LICENSE to LICENSE.
* Renamed DISCLAIMER to NOTICE.
Required code changes:
* Removed redundant HAVE_SPL macro.
* Removed _BOOT from nvpairs since it doesn't apply for Linux.
* Initial header cleanup (removal of empty headers, refactoring).
* Remove SPL repository clone/build from zimport.sh.
* Use of DEFINE_RATELIMIT_STATE and DEFINE_SPINLOCK removed due
to build issues when forcing C99 compilation.
* Replaced legacy ACCESS_ONCE with READ_ONCE.
* Include needed headers for `current` and `EXPORT_SYMBOL`.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
TEST_ZIMPORT_SKIP="yes"
Closes #7556
|
||
|
Pavel Zakharov
|
6cb8e5306d |
OpenZFS 9075 - Improve ZFS pool import/load process and corrupted pool recovery
Some work has been done lately to improve the debugability of the ZFS pool load (and import) process. This includes: 7638 Refactor spa_load_impl into several functions 8961 SPA load/import should tell us why it failed 7277 zdb should be able to print zfs_dbgmsg's To iterate on top of that, there's a few changes that were made to make the import process more resilient and crash free. One of the first tasks during the pool load process is to parse a config provided from userland that describes what devices the pool is composed of. A vdev tree is generated from that config, and then all the vdevs are opened. The Meta Object Set (MOS) of the pool is accessed, and several metadata objects that are necessary to load the pool are read. The exact configuration of the pool is also stored inside the MOS. Since the configuration provided from userland is external and might not accurately describe the vdev tree of the pool at the txg that is being loaded, it cannot be relied upon to safely operate the pool. For that reason, the configuration in the MOS is read early on. In the past, the two configurations were compared together and if there was a mismatch then the load process was aborted and an error was returned. The latter was a good way to ensure a pool does not get corrupted, however it made the pool load process needlessly fragile in cases where the vdev configuration changed or the userland configuration was outdated. Since the MOS is stored in 3 copies, the configuration provided by userland doesn't have to be perfect in order to read its contents. Hence, a new approach has been adopted: The pool is first opened with the untrusted userland configuration just so that the real configuration can be read from the MOS. The trusted MOS configuration is then used to generate a new vdev tree and the pool is re-opened. When the pool is opened with an untrusted configuration, writes are disabled to avoid accidentally damaging it. During reads, some sanity checks are performed on block pointers to see if each DVA points to a known vdev; when the configuration is untrusted, instead of panicking the system if those checks fail we simply avoid issuing reads to the invalid DVAs. This new two-step pool load process now allows rewinding pools accross vdev tree changes such as device replacement, addition, etc. Loading a pool from an external config file in a clustering environment also becomes much safer now since the pool will import even if the config is outdated and didn't, for instance, register a recent device addition. With this code in place, it became relatively easy to implement a long-sought-after feature: the ability to import a pool with missing top level (i.e. non-redundant) devices. Note that since this almost guarantees some loss of data, this feature is for now restricted to a read-only import. Porting notes (ZTS): * Fix 'make dist' target in zpool_import * The maximum path length allowed by tar is 99 characters. Several of the new test cases exceeded this limit resulting in them not being included in the tarball. Shorten the names slightly. * Set/get tunables using accessor functions. * Get last synced txg via the "zfs_txg_history" mechanism. * Clear zinject handlers in cleanup for import_cache_device_replaced and import_rewind_device_replaced in order that the zpool can be exported if there is an error. * Increase FILESIZE to 8G in zfs-test.sh to allow for a larger ext4 file system to be created on ZFS_DISK2. Also, there's no need to partition ZFS_DISK2 at all. The partitioning had already been disabled for multipath devices. Among other things, the partitioning steals some space from the ext4 file system, makes it difficult to accurately calculate the paramters to parted and can make some of the tests fail. * Increase FS_SIZE and FILE_SIZE in the zpool_import test configuration now that FILESIZE is larger. * Write more data in order that device evacuation take lonnger in a couple tests. * Use mkdir -p to avoid errors when the directory already exists. * Remove use of sudo in import_rewind_config_changed. Authored by: Pavel Zakharov <pavel.zakharov@delphix.com> Reviewed by: George Wilson <george.wilson@delphix.com> Reviewed by: Matthew Ahrens <mahrens@delphix.com> Reviewed by: Andrew Stormont <andyjstormont@gmail.com> Approved by: Hans Rosenfeld <rosenfeld@grumpf.hope-2000.org> Ported-by: Tim Chase <tim@chase2k.com> Signed-off-by: Tim Chase <tim@chase2k.com> OpenZFS-issue: https://illumos.org/issues/9075 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/619c0123 Closes #7459 |
||
|
Tom Caputi
|
be9a5c355c |
Add support for decryption faults in zinject
This patch adds the ability for zinject to trigger decryption and authentication faults in the ZIO and ARC layers. This functionality is exposed via the new "decrypt" error type, which may be provided for "data" object types. This patch also refactors some of the core encryption / decryption functions so that they have consistent prototypes, handle errors consistently, and do not have unused arguments. Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Tom Caputi <tcaputi@datto.com> Closes #7474 |
||
|
Matthew Ahrens
|
964c2d69a9 |
OpenZFS 9236 - nuke spa_dbgmsg
We should use zfs_dbgmsg instead of spa_dbgmsg. Or at least, metaslab_condense() should call zfs_dbgmsg because it's important and rare enough to always log. It's possible that the message in zio_dva_allocate() would be too high-frequency for zfs_dbgmsg. Authored by: Matthew Ahrens <mahrens@delphix.com> Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com> Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com> Reviewed by: George Wilson <george.wilson@delphix.com> Reviewed by: Richard Elling <Richard.Elling@RichardElling.com> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Approved by: Richard Lowe <richlowe@richlowe.net> Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov> Patch Notes: * Removed ZFS_DEBUG_SPA from zfs-module-parameters.5 OpenZFS-issue: https://www.illumos.org/issues/9236 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/cfaba7f668 Closes #7467 |
||
|
Matthew Ahrens
|
9e052db462 |
OpenZFS 9290 - device removal reduces redundancy of mirrors
Mirrors are supposed to provide redundancy in the face of whole-disk failure and silent damage (e.g. some data on disk is not right, but ZFS hasn't detected the whole device as being broken). However, the current device removal implementation bypasses some of the mirror's redundancy. Note that in no case is incorrect data returned, but we might get a checksum error when we should have been able to find the right data. There are two underlying problems: 1. When we remove a mirror device, we only read one side of the mirror. Since we can't verify the checksum, this side may be silently bad, but the good data is on the other side of the mirror (which we didn't read). This can cause the removal to "bake in" the busted data – all copies of the data in the new location are the same, busted version, while we left the good version behind. The fix for this is to read and copy both sides of the mirror. If the old and new vdevs are mirrors, we will read both sides of the old mirror, and write each copy to the corresponding side of the new mirror. (If the old and new vdevs have a different number of children, we will do this as best as possible.) Even though we aren't verifying checksums, this ensures that as long as there's a good copy of the data, we'll have a good copy after the removal, even if there's silent damage to one side of the mirror. If we're removing a mirror that has some silent damage, we'll have exactly the same damage in the new location (assuming that the new location is also a mirror). 2. When we read from an indirect vdev that points to a mirror vdev, we only consider one copy of the data. This can lead to reduced effective redundancy, because we might read a bad copy of the data from one side of the mirror, and not retry the other, good side of the mirror. Note that the problem is not with the removal process, but rather after the removal has completed (having copied correct data to both sides of the mirror), if one side of the new mirror is silently damaged, we encounter the problem when reading the relocated data via the indirect vdev. Also note that the problem doesn't occur when ZFS knows that one side of the mirror is bad, e.g. when a disk entirely fails or is offlined. The impact is that reads (from indirect vdevs that point to mirrors) may return a checksum error even though the good data exists on one side of the mirror, and scrub doesn't repair all data on the mirror (if some of it is pointed to via an indirect vdev). The fix for this is complicated by "split blocks" - one logical block may be split into two (or more) pieces with each piece moved to a different new location. In this case we need to read all versions of each split (one from each side of the mirror), and figure out which combination of versions results in the correct checksum, and then repair the incorrect versions. This ensures that we supply the same redundancy whether you use device removal or not. For example, if a mirror has small silent errors on all of its children, we can still reconstruct the correct data, as long as those errors are at sufficiently-separated offsets (specifically, separated by the largest block size - default of 128KB, but up to 16MB). Porting notes: * A new indirect vdev check was moved from dsl_scan_needs_resilver_cb() to dsl_scan_needs_resilver(), which was added to ZoL as part of the sequential scrub work. * Passed NULL for zfs_ereport_post_checksum()'s zbookmark_phys_t parameter. The extra parameter is unique to ZoL. * When posting indirect checksum errors the ABD can be passed directly, zfs_ereport_post_checksum() is not yet ABD-aware in OpenZFS. Authored by: Matthew Ahrens <mahrens@delphix.com> Reviewed by: Tim Chase <tim@chase2k.com> Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov> Ported-by: Tim Chase <tim@chase2k.com> OpenZFS-issue: https://illumos.org/issues/9290 OpenZFS-commit: https://github.com/openzfs/openzfs/pull/591 Closes #6900 |
||
|
Matthew Ahrens
|
a1d477c24c |
OpenZFS 7614, 9064 - zfs device evacuation/removal
OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1eb
Closes #6900
|
||
|
Tom Caputi
|
a2c2ed1bd4 |
Decryption error handling improvements
Currently, the decryption and block authentication code in the ZIO / ARC layers is a bit inconsistent with regards to the ereports that are produces and the error codes that are passed to calling functions. This patch ensures that all of these errors (which begin as ECKSUM) are converted to EIO before they leave the ZIO or ARC layer and that ereports are correctly generated on each decryption / authentication failure. In addition, this patch fixes a bug in zio_decrypt() where ECKSUM never gets written to zio->io_error. Reviewed by: Matt Ahrens <matt@delphix.com> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Tom Caputi <tcaputi@datto.com> Closes #7372 |
||
|
Olaf Faaland
|
cec3a0a1bb |
Report pool suspended due to MMP
When the pool is suspended, record whether it was due to an I/O error or due to MMP writes failing to succeed within the required time. Change spa_suspended from uint8_t to zio_suspend_reason_t to store the reason. When userspace queries pool status via spa_tryimport(), report the reason the pool was suspended in a new key, ZPOOL_CONFIG_SUSPENDED_REASON. In libzfs, when interpreting the returned config nvlist, report suspension due to MMP with a new pool status enum value, ZPOOL_STATUS_IO_FAILURE_MMP. In status_callback(), which generates and emits the message when 'zpool status' is executed, add a case to print an appropriate message for the new pool status enum value. Reviewed-by: George Melikov <mail@gmelikov.ru> Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: Tony Hutter <hutter2@llnl.gov> Signed-off-by: Olaf Faaland <faaland1@llnl.gov> Closes #7296 |
||
|
Tom Caputi
|
b1d217338a |
Raw receives must compress metadnode blocks
Currently, the DMU relies on ZIO layer compression to free LO dnode blocks that no longer have objects in them. However, raw receives disable all compression, meaning that these blocks can never be freed. In addition to the obvious space concerns, this could also cause incremental raw receives to fail to mount since the MAC of a hole is different from that of a completely zeroed block. This patch corrects this issue by adding a special case in zio_write_compress() which will attempt to compress these blocks to a hole even if ZIO_FLAG_RAW_ENCRYPT is set. This patch also removes the zfs_mdcomp_disable tunable, since tuning it could cause these same issues. Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Tom Caputi <tcaputi@datto.com> Closes #7198 |
||
|
George Wilson
|
ddc751d56b |
OpenZFS 8857 - zio_remove_child() panic due to already destroyed parent zio
PROBLEM
=======
It's possible for a parent zio to complete even though it has children
which have not completed. This can result in the following panic:
> $C
ffffff01809128c0 vpanic()
ffffff01809128e0 mutex_panic+0x58(fffffffffb94c904, ffffff597dde7f80)
ffffff0180912950 mutex_vector_enter+0x347(ffffff597dde7f80)
ffffff01809129b0 zio_remove_child+0x50(ffffff597dde7c58, ffffff32bd901ac0,
ffffff3373370908)
ffffff0180912a40 zio_done+0x390(ffffff32bd901ac0)
ffffff0180912a70 zio_execute+0x78(ffffff32bd901ac0)
ffffff0180912b30 taskq_thread+0x2d0(ffffff33bae44140)
ffffff0180912b40 thread_start+8()
> ::status
debugging crash dump vmcore.2 (64-bit) from batfs0390
operating system: 5.11 joyent_20170911T171900Z (i86pc)
image uuid: (not set)
panic message: mutex_enter: bad mutex, lp=ffffff597dde7f80
owner=ffffff3c59b39480 thread=ffffff0180912c40
dump content: kernel pages only
The problem is that dbuf_prefetch along with l2arc can create a zio tree
which confuses the parent zio and allows it to complete with while children
still exist. Here's the scenario:
zio tree:
pio
|--- lio
The parent zio, pio, has entered the zio_done stage and begins to check its
children to see there are still some that have not completed. In zio_done(),
the children are checked in the following order:
zio_wait_for_children(zio, ZIO_CHILD_VDEV, ZIO_WAIT_DONE)
zio_wait_for_children(zio, ZIO_CHILD_GANG, ZIO_WAIT_DONE)
zio_wait_for_children(zio, ZIO_CHILD_DDT, ZIO_WAIT_DONE)
zio_wait_for_children(zio, ZIO_CHILD_LOGICAL, ZIO_WAIT_DONE)
If pio, finds any child which has not completed then it stops executing and
goes to sleep. Each call to zio_wait_for_children() will grab the io_lock
while checking the particular child.
In this scenario, the pio has completed the first call to
zio_wait_for_children() to check for any ZIO_CHILD_VDEV children. Since
the only zio in the zio tree right now is the logical zio, lio, then it
completes that call and prepares to check the next child type.
In the meantime, the lio completes and in its callback creates a child vdev
zio, cio. The zio tree looks like this:
zio tree:
pio
|--- lio
|--- cio
The lio then grabs the parent's io_lock and removes itself.
zio tree:
pio
|--- cio
The pio continues to run but has already completed its check for ZIO_CHILD_VDEV
and will erroneously complete. When the child zio, cio, completes it will panic
the system trying to reference the parent zio which has been destroyed.
SOLUTION
========
The fix is to rework the zio_wait_for_children() logic to accept a bitfield
for all the children types that it's interested in checking. The
io_lock will is held the entire time we check all the children types. Since
the function now accepts a bitfield, a simple ZIO_CHILD_BIT() macro is provided
to allow for the conversion between a ZIO_CHILD type and the bitfield used by
the zio_wiat_for_children logic.
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andriy Gapon <avg@FreeBSD.org>
Reviewed by: Youzhong Yang <youzhong@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Dan McDonald <danmcd@omniti.com>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8857
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/862ff6d99c
Issue #5918
Closes #7168
|
||
|
Tom Caputi
|
ae76f45cda |
Encryption Stability and On-Disk Format Fixes
The on-disk format for encrypted datasets protects not only the encrypted and authenticated blocks themselves, but also the order and interpretation of these blocks. In order to make this work while maintaining the ability to do raw sends, the indirect bps maintain a secure checksum of all the MACs in the block below it along with a few other fields that determine how the data is interpreted. Unfortunately, the current on-disk format erroneously includes some fields which are not portable and thus cannot support raw sends. It is not possible to easily work around this issue due to a separate and much smaller bug which causes indirect blocks for encrypted dnodes to not be compressed, which conflicts with the previous bug. In addition, the current code generates incompatible on-disk formats on big endian and little endian systems due to an issue with how block pointers are authenticated. Finally, raw send streams do not currently include dn_maxblkid when sending both the metadnode and normal dnodes which are needed in order to ensure that we are correctly maintaining the portable objset MAC. This patch zero's out the offending fields when computing the bp MAC and ensures that these MACs are always calculated in little endian order (regardless of the host system's byte order). This patch also registers an errata for the old on-disk format, which we detect by adding a "version" field to newly created DSL Crypto Keys. We allow datasets without a version (version 0) to only be mounted for read so that they can easily be migrated. We also now include dn_maxblkid in raw send streams to ensure the MAC can be maintained correctly. This patch also contains minor bug fixes and cleanups. Reviewed-by: Jorgen Lundman <lundman@lundman.net> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed by: Matthew Ahrens <mahrens@delphix.com> Signed-off-by: Tom Caputi <tcaputi@datto.com> Closes #6845 Closes #6864 Closes #7052 |
||
|
Brian Behlendorf
|
8fb1ede146 |
Extend deadman logic
The intent of this patch is extend the existing deadman code
such that it's flexible enough to be used by both ztest and
on production systems. The proposed changes include:
* Added a new `zfs_deadman_failmode` module option which is
used to dynamically control the behavior of the deadman. It's
loosely modeled after, but independant from, the pool failmode
property. It can be set to wait, continue, or panic.
* wait - Wait for the "hung" I/O (default)
* continue - Attempt to recover from a "hung" I/O
* panic - Panic the system
* Added a new `zfs_deadman_ziotime_ms` module option which is
analogous to `zfs_deadman_synctime_ms` except instead of
applying to a pool TXG sync it applies to zio_wait(). A
default value of 300s is used to define a "hung" zio.
* The ztest deadman thread has been re-enabled by default,
aligned with the upstream OpenZFS code, and then extended
to terminate the process when it takes significantly longer
to complete than expected.
* The -G option was added to ztest to print the internal debug
log when a fatal error is encountered. This same option was
previously added to zdb in commit
|
||
|
Prakash Surya
|
2fe61a7ecc |
OpenZFS 8909 - 8585 can cause a use-after-free kernel panic
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: John Kennedy <jwk404@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Prakash Surya <prakash.surya@delphix.com>
PROBLEM
=======
There's a race condition that exists if `zil_free_lwb` races with either
`zil_commit_waiter_timeout` and/or `zil_lwb_flush_vdevs_done`.
Here's an example panic due to this bug:
> ::status
debugging crash dump vmcore.0 (64-bit) from ip-10-110-205-40
operating system: 5.11 dlpx-5.2.2.0_2017-12-04-17-28-32b6ba51fb (i86pc)
image uuid: 4af0edfb-e58e-6ed8-cafc-d3e9167c7513
panic message:
BAD TRAP: type=e (#pf Page fault) rp=ffffff0010555970 addr=60 occurred in module "zfs" due to a NULL pointer dereference
dump content: kernel pages only
> $c
zio_shrink+0x12()
zil_lwb_write_issue+0x30d(ffffff03dcd15cc0, ffffff03e0730e20)
zil_commit_waiter_timeout+0xa2(ffffff03dcd15cc0, ffffff03d97ffcf8)
zil_commit_waiter+0xf3(ffffff03dcd15cc0, ffffff03d97ffcf8)
zil_commit+0x80(ffffff03dcd15cc0, 9a9)
zfs_write+0xc34(ffffff03dc38b140, ffffff0010555e60, 40, ffffff03e00fb758, 0)
fop_write+0x5b(ffffff03dc38b140, ffffff0010555e60, 40, ffffff03e00fb758, 0)
write+0x250(42, fffffd7ff4832000, 2000)
sys_syscall+0x177()
If there's an outstanding lwb that's in `zil_commit_waiter_timeout`
waiting to timeout, waiting on it's waiter's CV, we must be sure not to
call `zil_free_lwb`. If we end up calling `zil_free_lwb`, then that LWB
may be freed and can result in a use-after-free situation where the
stale lwb pointer stored in the `zil_commit_waiter_t` structure of the
thread waiting on the waiter's CV is used.
A similar situation can occur if an lwb is issued to disk, and thus in
the `LWB_STATE_ISSUED` state, and `zil_free_lwb` is called while the
disk is servicing that lwb. In this situation, the lwb will be freed by
`zil_free_lwb`, which will result in a use-after-free situation when the
lwb's zio completes, and `zil_lwb_flush_vdevs_done` is called.
This race condition is prevented in `zil_close` by calling `zil_commit`
before `zil_free_lwb` is called, which will ensure all outstanding (i.e.
all lwb's in the `LWB_STATE_OPEN` and/or `LWB_STATE_ISSUED` states)
reach the `LWB_STATE_DONE` state before the lwb's are freed
(`zil_commit` will not return untill all the lwb's are
`LWB_STATE_DONE`).
Further, this race condition is prevented in `zil_sync` by only calling
`zil_free_lwb` for lwb's that do not have their `lwb_buf` pointer set.
All lwb's not in the `LWB_STATE_DONE` state will have a non-null value
for this pointer; the pointer is only cleared in
`zil_lwb_flush_vdevs_done`, at which point the lwb's state will be
changed to `LWB_STATE_DONE`.
This race *is* present in `zil_suspend`, leading to this bug.
At first glance, it would appear as though this would not be true
because `zil_suspend` will call `zil_commit`, just like `zil_close`, but
the problem is that `zil_suspend` will set the zilog's `zl_suspend`
field prior to calling `zil_commit`. Further, in `zil_commit`, if
`zl_suspend` is set, `zil_commit` will take a special branch of logic
and use `txg_wait_synced` instead of performing the normal `zil_commit`
logic.
This call to `txg_wait_synced` might be good enough for the data to
reach disk safely before it returns, but it does not ensure that all
outstanding lwb's reach the `LWB_STATE_DONE` state before it returns.
This is because, if there's an lwb "stuck" in
`zil_commit_waiter_timeout`, waiting for it's lwb to timeout, it will
maintain a non-null value for it's `lwb_buf` field and thus `zil_sync`
will not free that lwb. Thus, even though the lwb's data is already on
disk, the lwb will be left lingering, waiting on the CV, and will
eventually timeout and be issued to disk even though the write is
unnecessary.
So, after `zil_commit` is called from `zil_suspend`, we incorrectly
assume that there are not outstanding lwb's, and proceed to free all
lwb's found on the zilog's lwb list. As a result, we free the lwb that
will later be used `zil_commit_waiter_timeout`.
SOLUTION
========
The solution to this, is to ensure all outstanding lwb's complete before
calling `zil_free_lwb` via `zil_destroy` in `zil_suspend`. This patch
accomplishes this goal by forcing the normal `zil_commit` logic when
called from `zil_sync`.
Now, `zil_suspend` will call `zil_commit_impl` which will always use the
normal logic of waiting/issuing lwb's to disk before it returns. As a
result, any lwb's outstanding when `zil_commit_impl` is called will be
guaranteed to reach the `LWB_STATE_DONE` state by the time it returns.
Further, no new lwb's will be created via `zil_commit` since the zilog's
`zl_suspend` flag will be set. This will force all new callers of
`zil_commit` to use `txg_wait_synced` instead of creating and issuing
new lwb's.
Thus, all lwb's left on the zilog's lwb list when `zil_destroy` is
called will be in the `LWB_STATE_DONE` state, and we'll avoid this race
condition.
OpenZFS-issue: https://www.illumos.org/issues/8909
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ece62b6f8d
Closes #6940
|
||
|
Tom Caputi
|
a8b2e30685 |
Support re-prioritizing asynchronous prefetches
When sequential scrubs were merged, all calls to arc_read() (including prefetch IOs) were given ZIO_PRIORITY_ASYNC_READ. Unfortunately, this behaves badly with an existing issue where prefetch IOs cannot be re-prioritized after the issue. The result is that synchronous reads end up in the same vdev_queue as the scrub IOs and can have (in some workloads) multiple seconds of latency. This patch incorporates 2 changes. The first ensures that all scrub IOs are given ZIO_PRIORITY_SCRUB to allow the vdev_queue code to differentiate between these I/Os and user prefetches. Second, this patch introduces zio_change_priority() to provide the missing capability to upgrade a zio's priority. Reviewed by: George Wilson <george.wilson@delphix.com> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Tom Caputi <tcaputi@datto.com> Closes #6921 Closes #6926 |
||
|
Prakash Surya
|
1ce23dcaff |
OpenZFS 8585 - improve batching done in zil_commit()
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Prakash Surya <prakash.surya@delphix.com>
Problem
=======
The current implementation of zil_commit() can introduce significant
latency, beyond what is inherent due to the latency of the underlying
storage. The additional latency comes from two main problems:
1. When there's outstanding ZIL blocks being written (i.e. there's
already a "writer thread" in progress), then any new calls to
zil_commit() will block waiting for the currently oustanding ZIL
blocks to complete. The blocks written for each "writer thread" is
coined a "batch", and there can only ever be a single "batch" being
written at a time. When a batch is being written, any new ZIL
transactions will have to wait for the next batch to be written,
which won't occur until the current batch finishes.
As a result, the underlying storage may not be used as efficiently
as possible. While "new" threads enter zil_commit() and are blocked
waiting for the next batch, it's possible that the underlying
storage isn't fully utilized by the current batch of ZIL blocks. In
that case, it'd be better to allow these new threads to generate
(and issue) a new ZIL block, such that it could be serviced by the
underlying storage concurrently with the other ZIL blocks that are
being serviced.
2. Any call to zil_commit() must wait for all ZIL blocks in its "batch"
to complete, prior to zil_commit() returning. The size of any given
batch is proportional to the number of ZIL transaction in the queue
at the time that the batch starts processing the queue; which
doesn't occur until the previous batch completes. Thus, if there's a
lot of transactions in the queue, the batch could be composed of
many ZIL blocks, and each call to zil_commit() will have to wait for
all of these writes to complete (even if the thread calling
zil_commit() only cared about one of the transactions in the batch).
To further complicate the situation, these two issues result in the
following side effect:
3. If a given batch takes longer to complete than normal, this results
in larger batch sizes, which then take longer to complete and
further drive up the latency of zil_commit(). This can occur for a
number of reasons, including (but not limited to): transient changes
in the workload, and storage latency irregularites.
Solution
========
The solution attempted by this change has the following goals:
1. no on-disk changes; maintain current on-disk format.
2. modify the "batch size" to be equal to the "ZIL block size".
3. allow new batches to be generated and issued to disk, while there's
already batches being serviced by the disk.
4. allow zil_commit() to wait for as few ZIL blocks as possible.
5. use as few ZIL blocks as possible, for the same amount of ZIL
transactions, without introducing significant latency to any
individual ZIL transaction. i.e. use fewer, but larger, ZIL blocks.
In theory, with these goals met, the new allgorithm will allow the
following improvements:
1. new ZIL blocks can be generated and issued, while there's already
oustanding ZIL blocks being serviced by the storage.
2. the latency of zil_commit() should be proportional to the underlying
storage latency, rather than the incoming synchronous workload.
Porting Notes
=============
Due to the changes made in commit
|
||
|
Tom Caputi
|
d4a72f2386 |
Sequential scrub and resilvers
Currently, scrubs and resilvers can take an extremely long time to complete. This is largely due to the fact that zfs scans process pools in logical order, as determined by each block's bookmark. This makes sense from a simplicity perspective, but blocks in zfs are often scattered randomly across disks, particularly due to zfs's copy-on-write mechanisms. This patch improves performance by splitting scrubs and resilvers into a metadata scanning phase and an IO issuing phase. The metadata scan reads through the structure of the pool and gathers an in-memory queue of I/Os, sorted by size and offset on disk. The issuing phase will then issue the scrub I/Os as sequentially as possible, greatly improving performance. This patch also updates and cleans up some of the scan code which has not been updated in several years. Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Authored-by: Saso Kiselkov <saso.kiselkov@nexenta.com> Authored-by: Alek Pinchuk <apinchuk@datto.com> Authored-by: Tom Caputi <tcaputi@datto.com> Signed-off-by: Tom Caputi <tcaputi@datto.com> Closes #3625 Closes #6256 |
||
|
Don Brady
|
1c27024e22 |
Undo c89 workarounds to match with upstream
With PR 5756 the zfs module now supports c99 and the remaining past c89 workarounds can be undone. Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: George Melikov <mail@gmelikov.ru> Signed-off-by: Don Brady <don.brady@delphix.com> Closes #6816 |
||
|
Tom Caputi
|
4807c0badb |
Encryption patch follow-up
* PBKDF2 implementation changed to OpenSSL implementation. * HKDF implementation moved to its own file and tests added to ensure correctness. * Removed libzfs's now unnecessary dependency on libzpool and libicp. * Ztest can now create and test encrypted datasets. This is currently disabled until issue #6526 is resolved, but otherwise functions as advertised. * Several small bug fixes discovered after enabling ztest to run on encrypted datasets. * Fixed coverity defects added by the encryption patch. * Updated man pages for encrypted send / receive behavior. * Fixed a bug where encrypted datasets could receive DRR_WRITE_EMBEDDED records. * Minor code cleanups / consolidation. Signed-off-by: Tom Caputi <tcaputi@datto.com> |
||
|
Don Brady
|
d977122da9 |
Add corruption failure option to zinject(8)
Added a 'corrupt' error option that will flip a bit in the data after a read operation. This is useful for generating checksum errors at the device layer (in a mirror config for example). It is also used to validate the diagnosis of checksum errors from the zfs diagnosis engine. Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Don Brady <don.brady@intel.com> Closes #6345 |
||
|
Tom Caputi
|
b525630342 |
Native Encryption for ZFS on Linux
This change incorporates three major pieces: The first change is a keystore that manages wrapping and encryption keys for encrypted datasets. These commands mostly involve manipulating the new DSL Crypto Key ZAP Objects that live in the MOS. Each encrypted dataset has its own DSL Crypto Key that is protected with a user's key. This level of indirection allows users to change their keys without re-encrypting their entire datasets. The change implements the new subcommands "zfs load-key", "zfs unload-key" and "zfs change-key" which allow the user to manage their encryption keys and settings. In addition, several new flags and properties have been added to allow dataset creation and to make mounting and unmounting more convenient. The second piece of this patch provides the ability to encrypt, decyrpt, and authenticate protected datasets. Each object set maintains a Merkel tree of Message Authentication Codes that protect the lower layers, similarly to how checksums are maintained. This part impacts the zio layer, which handles the actual encryption and generation of MACs, as well as the ARC and DMU, which need to be able to handle encrypted buffers and protected data. The last addition is the ability to do raw, encrypted sends and receives. The idea here is to send raw encrypted and compressed data and receive it exactly as is on a backup system. This means that the dataset on the receiving system is protected using the same user key that is in use on the sending side. By doing so, datasets can be efficiently backed up to an untrusted system without fear of data being compromised. Reviewed by: Matthew Ahrens <mahrens@delphix.com> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: Jorgen Lundman <lundman@lundman.net> Signed-off-by: Tom Caputi <tcaputi@datto.com> Closes #494 Closes #5769 |
||
|
sanjeevbagewadi
|
21df134f4c |
zio_dva_throttle_done() should allow zinjected ZIO
If fault injection is enabled, the ZIO_FLAG_IO_RETRY could be set by zio_handle_device_injection() to generate the FMA events and update stats. Hence, ignore the flag and process such zios. A better fix would be to add another flag in the zio_t to indicate that the zio is failed because of a zinject rule. However, considering the fact that we do this in debug bits, we could do with the crude check using the global flag zio_injection_enabled which is set to 1 when zinject records are added. Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Sanjeev Bagewadi <sanjeev.bagewadi@gmail.com> Closes #6383 Closes #6384 |
||
|
Tony Hutter
|
6710381680 |
Only record zio->io_delay on reads and writes
While investigating https://github.com/zfsonlinux/zfs/issues/6425 I noticed that ioctl ZIOs were not setting zio->io_delay correctly. They would set the start time in zio_vdev_io_start(), but never set the end time in zio_vdev_io_done(), since ioctls skip it and go straight to zio_done(). This was causing spurious "delayed IO" events to appear, which would eventually get rate-limited and displayed as "Missed events" messages in zed. To get around the problem, this patch only sets zio->io_delay for read and write ZIOs, since that's all we care about anyway. Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov> Reviewed-by: George Melikov <mail@gmelikov.ru> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Tony Hutter <hutter2@llnl.gov> Closes #6425 Closes #6440 |
||
|
Olaf Faaland
|
f43615d0cc |
Revert Fix vdev_probe() call wrt SCL_STATE_ALL
This reverts commit
|
||
|
Brian Behlendorf
|
cc9c6bcb73 |
Fix vdev_probe() call outside SCL_STATE_ALL lock
When an IO fails then zio_vdev_io_done() can call vdev_probe() to determine the health of the vdev. This is safe as long as the original zio was submitted with zio_wait() and holds the SCL_STATE_ALL lock over the operation. If zio_no_wait() was used then the done callback will submit the probe IO outside the SCL_STATE_ALL lock and hit this ASSERT in zio_create() ASSERT(!vd || spa_config_held(spa, SCL_STATE_ALL, RW_READER)); Resolve the issue by only allowing vdev_probe() to be called when there's a waiter indicating the caller is using zio_wait(). This assumes that caller is still holding SCL_STATE_ALL. This issue isn't MMP specific but was surfaced when testing. Without this patch it can be reproduced by running: zpool set multihost on <pool> zinject -d <vdev> -e io -T write -f 50 <pool> -L uber Reviewed-by: Olaf Faaland <faaland1@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Don Brady <don.brady@intel.com> Closes #745 Closes #6279 |
||
|
Giuseppe Di Natale
|
1b7c1e5ce9 |
OpenZFS 7578 - Fix/improve some aspects of ZIL writing
- After some ZIL changes 6 years ago zil_slog_limit got partially broken due to zl_itx_list_sz not updated when async itx'es upgraded to sync. Actually because of other changes about that time zl_itx_list_sz is not really required to implement the functionality, so this patch removes some unneeded broken code and variables. - Original idea of zil_slog_limit was to reduce chance of SLOG abuse by single heavy logger, that increased latency for other (more latency critical) loggers, by pushing heavy log out into the main pool instead of SLOG. Beside huge latency increase for heavy writers, this implementation caused double write of all data, since the log records were explicitly prepared for SLOG. Since we now have I/O scheduler, I've found it can be much more efficient to reduce priority of heavy logger SLOG writes from ZIO_PRIORITY_SYNC_WRITE to ZIO_PRIORITY_ASYNC_WRITE, while still leave them on SLOG. - Existing ZIL implementation had problem with space efficiency when it has to write large chunks of data into log blocks of limited size. In some cases efficiency stopped to almost as low as 50%. In case of ZIL stored on spinning rust, that also reduced log write speed in half, since head had to uselessly fly over allocated but not written areas. This change improves the situation by offloading problematic operations from z*_log_write() to zil_lwb_commit(), which knows real situation of log blocks allocation and can split large requests into pieces much more efficiently. Also as side effect it removes one of two data copy operations done by ZIL code WR_COPIED case. - While there, untangle and unify code of z*_log_write() functions. Also zfs_log_write() alike to zvol_log_write() can now handle writes crossing block boundary, that may also improve efficiency if ZPL is made to do that. Sponsored by: iXsystems, Inc. Authored by: Alexander Motin <mav@FreeBSD.org> Reviewed by: Matthew Ahrens <mahrens@delphix.com> Reviewed by: Prakash Surya <prakash.surya@delphix.com> Reviewed by: Andriy Gapon <avg@FreeBSD.org> Reviewed by: Steven Hartland <steven.hartland@multiplay.co.uk> Reviewed by: Brad Lewis <brad.lewis@delphix.com> Reviewed by: Richard Elling <Richard.Elling@RichardElling.com> Approved by: Robert Mustacchi <rm@joyent.com> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: Richard Yao <ryao@gentoo.org> Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov> OpenZFS-issue: https://www.illumos.org/issues/7578 OpenZFS-commit: https://github.com/openzfs/openzfs/commit/aeb13ac Closes #6191 |
||
|
jxiong
|
24fa20340d |
Guarantee PAGESIZE alignment for large zio buffers
In current implementation, only zio buffers in 16KB and bigger are guaranteed PAGESIZE alignment. This breaks Lustre since it assumes that 'arc_buf_t::b_data' must be page aligned when zio buffers are greater than or equal to PAGESIZE. This patch will make the zio buffers to be PAGESIZE aligned when the sizes are not less than PAGESIZE. This change may cause a little bit memory waste but that should be fine because after ABD is introduced, zio buffers are used to hold data temporarily and live in memory for a short while. Reviewed-by: Don Brady <don.brady@intel.com> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Jinshan Xiong <jinshan.xiong@gmail.com> Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com> Closes #6084 |