This continues what was started in
0eef1bde31 by fully converting zvols
to avoid unnecessary dnode_hold() calls. This saves a small amount
of CPU time and slightly improves latencies of operations on zvols.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@prophetstor.com>
Closes#6058
Buildbots and zfs-tests regularly see 7 kilobytes of stack
usage with this function. Convert self-calls to iterations
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#6219
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
The send size estimate for a zvol can be too low, if the size of the
record headers (dmu_replay_record_t's) is a significant portion of the
size. This is typically the case when the data is highly compressible,
especially with embedded blocks.
The problem is that dmu_adjust_send_estimate_for_indirects() assumes
that blocks are the size of the "recordsize" property (128KB). However,
for zvols, the blocks are the size of the "volblocksize" property (8KB).
Therefore, we estimate that there will be 16x less record headers than
there really will be.
The fix is to check the type of the object set (whether it is a zvol or
not) and pick the appropriate property. In addition, while we are at it,
we also add the size of the BEGIN and END records to the estimate.
OpenZFS-issue: https://www.illumos.org/issues/8056
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/faf09cdCloses#6205
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
dbuf_evict_notify() holds the dbuf_evict_lock while checking if it should
do the eviction itself (because the evict thread is not able to keep up).
This can result in massive lock contention. It isn't necessary to hold
the lock, because if we make the wrong choice occasionally, nothing bad
will happen. This commit results in a ~60% performance improvement for
ARC-cached sequential reads.
OpenZFS-issue: https://www.illumos.org/issues/8156
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f73e5d9Closes#6204
dmu_object_alloc() is single-threaded, so when multiple threads are
creating files in a single filesystem, they spend a lot of time waiting
for the os_obj_lock. To improve performance of multi-threaded file
creation, we must make dmu_object_alloc() typically not grab any
filesystem-wide locks.
The solution is to have a "next object to allocate" for each CPU. Each
of these "next object"s is in a different block of the dnode object, so
that concurrent allocation holds dnodes in different dbufs. When a
thread's "next object" reaches the end of a chunk of objects (by default
4 blocks worth -- 128 dnodes), it will be reset to the per-objset
os_obj_next, which will be increased by a chunk of objects (128). Only
when manipulating the os_obj_next will we need to grab the os_obj_lock.
This decreases lock contention dramatically, because each thread only
needs to grab the os_obj_lock briefly, once per 128 allocations.
This results in a 70% performance improvement to multi-threaded object
creation (where each thread is creating objects in its own directory),
from 67,000/sec to 115,000/sec, with 8 CPUs.
Work sponsored by Intel Corp.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/8199
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/374Closes#4703Closes#6117
- After some ZIL changes 6 years ago zil_slog_limit got partially broken
due to zl_itx_list_sz not updated when async itx'es upgraded to sync.
Actually because of other changes about that time zl_itx_list_sz is not
really required to implement the functionality, so this patch removes
some unneeded broken code and variables.
- Original idea of zil_slog_limit was to reduce chance of SLOG abuse by
single heavy logger, that increased latency for other (more latency critical)
loggers, by pushing heavy log out into the main pool instead of SLOG. Beside
huge latency increase for heavy writers, this implementation caused double
write of all data, since the log records were explicitly prepared for SLOG.
Since we now have I/O scheduler, I've found it can be much more efficient
to reduce priority of heavy logger SLOG writes from ZIO_PRIORITY_SYNC_WRITE
to ZIO_PRIORITY_ASYNC_WRITE, while still leave them on SLOG.
- Existing ZIL implementation had problem with space efficiency when it
has to write large chunks of data into log blocks of limited size. In some
cases efficiency stopped to almost as low as 50%. In case of ZIL stored on
spinning rust, that also reduced log write speed in half, since head had to
uselessly fly over allocated but not written areas. This change improves
the situation by offloading problematic operations from z*_log_write() to
zil_lwb_commit(), which knows real situation of log blocks allocation and
can split large requests into pieces much more efficiently. Also as side
effect it removes one of two data copy operations done by ZIL code WR_COPIED
case.
- While there, untangle and unify code of z*_log_write() functions.
Also zfs_log_write() alike to zvol_log_write() can now handle writes crossing
block boundary, that may also improve efficiency if ZPL is made to do that.
Sponsored by: iXsystems, Inc.
Authored by: Alexander Motin <mav@FreeBSD.org>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Andriy Gapon <avg@FreeBSD.org>
Reviewed by: Steven Hartland <steven.hartland@multiplay.co.uk>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7578
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/aeb13acCloses#6191
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
When writing pre-compressed buffers, arc_write() requires that
the compression algorithm used to compress the buffer matches
the compression algorithm requested by the zio_prop_t, which is
set by dmu_write_policy(). This makes dmu_write_policy() and its
callers a bit more complicated.
We simplify this by making arc_write() trust the caller to supply
the type of pre-compressed buffer that it wants to write,
and override the compression setting in the zio_prop_t.
OpenZFS-issue: https://www.illumos.org/issues/8155
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b55ff58Closes#6200
Since torvalds/linux@d0a5b99 IOP_XATTR is used to indicate the inode
has xattr support: clear it for the ctldir inodes to avoid EIO errors.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6189
When inheriting the "snapdev" property to we don't always call
zfs_prop_set_special(): this prevents device nodes from being created in
certain situations. Because "snapdev" is the only *special* property
that is also inheritable we need to call zfs_prop_set_special() even
when we're not reverting it to the received value ('zfs inherit -S').
Additionally, fix a NULL pointer dereference accidentally introduced in
5559ba0 that can be triggered when setting the "snapdev" property to
the value "hidden" twice.
Finally, add a new test case "zvol_misc_snapdev" to the ZFS Test Suite.
Reviewed by: Boris Protopopov <bprotopopov@hotmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6131Closes#6175Closes#6176
If, for example, your aux device was /dev/sdc, but now the aux device is
removed and /dev/sdc points to other device. zpool import will still
use that device and corrupt it.
The problem is that the spa_validate_aux in spa_import, rather than
validate the on-disk label, it would actually write label to disk. We
remove them since spa_load_{spares,l2cache} seems to do everything we
need and they would actually validate on-disk label.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#6158
Move kmem_free() so it's called for every error path: this is
preferred over making `dmu_object_info_t doi` local to accommodate
older kernels with limited stacks.
Reviewed by: Boris Protopopov <bprotopopov@hotmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6177
Added missing ida_simple_remove() in the error handling path.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Closes#6159Closes#6172
In certain cases (dsl_scan_sync() is one), we may end up calling
bpobj_iterate() on an empty bpobj. Even though we don't end up
modifying the bpobj it still gets dirtied, causing unneeded writes
to the pool.
This patch adds an early bail from bpobj_iterate_impl() if bpobj
is empty to prevent unneeded writes.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6164
This reverts commit 959f56b993.
An issue was uncovered by the new zvol_misc_snapdev test case
which needs to be investigated and resolved.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6174
Issue #6131
When inheriting the "snapdev" property to we don't always call
zfs_prop_set_special(): this prevents device nodes from being created in
certain situations. Because "snapdev" is the only *special* property
that is also inheritable we need to call zfs_prop_set_special() even
when we're not reverting it to the received value ('zfs inherit -S').
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6131
Provide a format parameter to super_setup_bdi_name() so we don't
create duplicate names in '/devices/virtual/bdi' sysfs namespace which
would prevent us from mounting more than one ZFS filesystem at a time.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6147
Sync with kernel patches for lz4
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable.git/log/lib/lz4
4a3a99 lz4: add overrun checks to lz4_uncompress_unknownoutputsize()
d5e7ca LZ4 : fix the data abort issue
bea2b5 lib/lz4: Pull out constant tables
99b7e9 lz4: fix system halt at boot kernel on x86_64
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Feng Sun <loyou85@gmail.com>
Closes#5975Closes#5973
This addition will enable us to sync an open TXG to the main pool
on demand. The functionality is similar to 'sync(2)' but 'zpool sync'
will return when data has hit the main storage instead of potentially
just the ZIL as is the case with the 'sync(2)' cmd.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6122
This patch adds a '-f' option to 'zpool offline' to fault a vdev
instead of bringing it offline. Unlike the OFFLINE state, the
FAULTED state will trigger the FMA code, allowing for things like
autoreplace and triggering the slot fault LED. The -f faults
persist across imports, unless they were set with the temporary
(-t) flag. Both persistent and temporary faults can be cleared
with zpool clear.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6094
One pre-check in zfs_ereport_start() was being called after
the nvlists were being allocated. This simply corrects that
issue.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6140
The lock is designed to protect internal state of zvol_state_t and
to avoid taking spa_namespace_lock (e.g. in dmu_objset_own() code path)
while holding zvol_stat_lock. Refactor the code accordingly.
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3484Closes#6065Closes#6134
Fix lock order inversion with zvol_open() as it did not account
for use of zvols as vdevs. The latter use cases resulted in the
lock order inversion deadlocks that involved spa_namespace_lock
and bdev->bd_mutex.
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #6065
Issue #6134
On a raidz vdev, a block that does not span all child vdevs, excluding
its skip sectors if any, may not be affected by a child vdev outage or
failure. In such cases, the block does not need to be resilvered.
However, current resilver algorithm simply resilvers all blocks on a
degraded raidz vdev. Such spurious IO is not only wasteful, but also
adds the risk of overwriting good data.
This patch eliminates such spurious IOs.
Reviewed-by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Isaac Huang <he.huang@intel.com>
Closes#5316
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
A standard practice in ZFS is to keep track of "per-txg" state. Any of
the 3 active TXG's (open, quiescing, syncing) can have different values
for this state. We should assert that we do not attempt to modify other
(inactive) TXG's.
Porting Notes:
- ASSERTV added to txg_sync_waiting() for unused variable.
OpenZFS-issue: https://www.illumos.org/issues/8063
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/01acb46Closes#6109
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Matthew Ahrens <mahrens@delphix.com>
If we do a scrub while a leaf device is offline (via "zpool offline"),
we will inadvertently clear the DTL (dirty time log) of the offline
device, even though it is still damaged. When the device comes back
online, we will incompletely resilver it, thinking that the scrub
repaired blocks written before the scrub was started. The incomplete
resilver can lead to data loss if there is a subsequent failure of a
different leaf device.
The fix is to never clear the DTL of offline devices. Note that if a
device is onlined while a scrub is in progress, the scrub will be
restarted.
The problem can be worked around by running "zpool scrub" after
"zpool online".
OpenZFS-issue: https://www.illumos.org/issues/8166
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/372Closes#5806Closes#6103
The arc layer tracks checksums of its data in the arc header
so that it can ensure that buffers haven't changed when they're
not supposed to. This checksum is only maintained while there
is an uncompressed buffer still attached to the header.
Unfortunately there is a missing call to arc_free_cksum() in
arc_release() that can trigger ASSERTs. This has not been a
common issue because the checksums are only maintained for
debug builds and triggering the bug requires writing a block
(and therefore calling arc_release()) while a compressed buffer
is still being used on a debug build. This simply corrects the
issue.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6105
Linux 4.9 added current_time() as the preferred interface to get
the filesystem time. CURRENT_TIME was retired in Linux 4.12.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6114
This allows users to specify "-o property=value" to override and
"-x property" to exclude properties when receiving a zfs send stream.
Both native and user properties can be specified.
This is useful when using zfs send/receive for periodic
backup/replication because it lets users change properties such as
canmount, mountpoint, or compression without modifying the source.
References:
https://www.illumos.org/issues/2745https://www.illumos.org/issues/3753
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#1350Closes#5349
Document the existence of `createtxg` and `guid` native properties
in man pages and zfs command output.
One of the great features of ZFS is incremental replication of
snapshots, possibly between pools on different machines.
Shell scripts are commonly used to auomate this procedure. They have to
find the most recent common snapshot between both sides and then
perform incremental send & recv.
Currently, scripts rely on the sorting order of `zfs list`, which
defaults to `createtxg`, and the assumption that snapshot names on
either side do not change.
By making `createtxg` and `guid` part of the public ZFS interface,
scripts are enabled to use
a) `createtxg` to determine the logical & temporal order of snapshots
(the creation property is not an equivalent substitute since
multiple snapshots may be created within one second)
b) `guid` to uniquely identify a snapshot, independent of its current
display name
This has the potential of making scripts safer and correct.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: DHE <git@dehacked.net>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#6102
zfsonlinux/spl@8f87971 added __spl_pf_fstrans_check for the xfs related
check, so we use them accordingly.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#6113
Remove the lz4_ac local variable from dmu_write_policy() to resolve
the following unused variable warning on non-debug builds.
dmu.c: In function ‘dmu_write_policy’:
dmu.c:1892:12: warning: unused variable ‘lz4_ac’ [-Wunused-variable]
boolean_t lz4_ac = spa_feature_is_active(os->os_spa,
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The proposed debugging enhancements in zfsonlinux/spl#587
identified the following missing *_destroy/*_fini calls.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#5428
Change the default ZVOL behavior so requests are handled asynchronously.
This behavior is functionally the same as in the zfs-0.6.4 release.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #5902
Linux has read-ahead logic designed to accelerate sequential workloads.
ZFS has its own read-ahead logic called zprefetch that operates on both
ZVOLs and datasets. Having two prefetchers active at the same time can
cause overprefetching, which unnecessarily reduces IOPS performance on
CoW filesystems like ZFS.
Testing shows that entirely disabling the Linux prefetch results in
a significant performance penalty for reads while commensurate benefits
are seen in random writes. It appears that read-ahead benefits are
inversely proportional to random write benefits, and so a single page
of Linux-layer read-ahead appears to offer the middle ground for both
workloads.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Issue #5902
The current ZVOL implementation does not explicitly set merge
options on ZVOL device queues, which results in the default merge
behavior.
Explicitly set QUEUE_FLAG_NOMERGES on ZVOL queues allowing the
ZIO pipeline to do its work.
Initial benchmarks (tiotest with no O_DIRECT) show random write
performance going up almost 3X on 8K ZVOLs, even after significant
rewrites of the logical space allocation.
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: RageLtMan <rageltman@sempervictus>
Issue #5902
This commit allow higher ashift values (up to 16) in 'zpool create'
The ashift value was previously limited to 13 (8K block) in b41c990
because the limited number of uberblocks we could fit in the
statically sized (128K) vdev label ring buffer could prevent the
ability the safely roll back a pool to recover it.
Since b02fe35 the largest uberblock size we support is 8K: this
allow us to store a minimum number of 16 uberblocks in the vdev
label, even with higher ashift values.
Additionally change 'ashift' pool property behaviour: if set it will
be used as the default hint value in subsequent vdev operations
('zpool add', 'attach' and 'replace'). A custom ashift value can still
be specified from the command line, if desired.
Finally, fix a bug in add-o_ashift.ksh caused by a missing variable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2024Closes#4205Closes#4740Closes#5763
When vdev_psize increases, the location of labels 2 and 3 changes
because their location is relative to the end of the device.
The configs for labels 2 and 3 are written during the next spa_sync()
because the vdev is added to the dirty config list. However, the
uberblock rings are not re-written in their new location, leaving the
device vulnerable to the beginning of the device being overwritten or
damaged.
This patch copies the uberblock ring from label 0 to labels 2 and 3,
in their new locations, at the next sync after vdev_psize increases.
Also, add a test zpool_expand_004_pos.ksh to confirm the uberblocks
are copied.
Reviewed-by: BearBabyLiu <liu.huang@zte.com.cn>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5108
When multiple filesystems are in use, memory pressure causes arc_cache
to collapse to a minimum. Allow arc_cache to maintain proportional size
even when hit rates are disproportionate. We do this only via evictable
size from the kernel shrinker, thus it's only in effect under memory
pressure.
AKAMAI: zfs: CR 3695072
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Closes#6035
Could return the wrong pages value
AKAMAI: zfs: CR 3695072
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Issue #6035
Calling it when nothing is evictable will cause extra kswapd cpu. Also
if we didn't shrink it's unlikely to have memory to reap because we
likely just called it microseconds ago. The exception is if we are in
direct reclaim.
You can see how hard this is being hit in kswapd with a light test
workload:
34.95% [zfs] [k] arc_kmem_reap_now
5.40% [spl] [k] spl_kmem_cache_reap_now
3.79% [kernel] [k] _raw_spin_lock
2.86% [spl] [k] __spl_kmem_cache_generic_shrinker.isra.7
2.70% [kernel] [k] shrink_slab.part.37
1.93% [kernel] [k] isolate_lru_pages.isra.43
1.55% [kernel] [k] __wake_up_bit
1.20% [kernel] [k] super_cache_count
1.20% [kernel] [k] __radix_tree_lookup
With ZFS just mounted but only ext4/pagecache memory pressure
arc_kmem_reap_now still consumes excessive CPU:
12.69% [kernel] [k] isolate_lru_pages.isra.43
10.76% [kernel] [k] free_pcppages_bulk
7.98% [kernel] [k] drop_buffers
7.31% [kernel] [k] shrink_page_list
6.44% [zfs] [k] arc_kmem_reap_now
4.19% [kernel] [k] free_hot_cold_page
4.00% [kernel] [k] __slab_free
3.95% [kernel] [k] __isolate_lru_page
3.09% [kernel] [k] __radix_tree_lookup
Same pagecache only workload as above with this patch series:
11.58% [kernel] [k] isolate_lru_pages.isra.43
11.20% [kernel] [k] drop_buffers
9.67% [kernel] [k] free_pcppages_bulk
8.44% [kernel] [k] shrink_page_list
4.86% [kernel] [k] __isolate_lru_page
4.43% [kernel] [k] free_hot_cold_page
4.00% [kernel] [k] __slab_free
3.44% [kernel] [k] __radix_tree_lookup
(arc_kmem_reap_now has 0 samples in perf)
AKAMAI: zfs: CR 3695042
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Issue #6035
Lock contention, by itself, shouldn't indicate a stop condition to the
kernel's slab shrinker. Doing so can cause stalls when the kernel is
trying to free large parts of the cache such as is done by drop_caches
Also, perhaps arc_reclaim_lock should be a spinlock, and this code
eliminated.
AKAMAI: zfs: CR 3593801
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Issue #6035
Move arcstat_need_free increment from all direct calls to when
arc_reclaim_lock is busy and we exit wihout doing anything. Data will
be reclaimed in reclaim thread. The previous location meant that we
both reclaim the memory in this thread, and also schedule the same
amount of memory for reclaim in arc_reclaim, effectively doubling the
requested reclaim.
AKAMAI: zfs: CR 3695072
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Issue #6035
Ensures proper accounting of bytes we requested to free
AKAMAI: zfs: CR 3695072
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Issue #6035
Ghost meta/data buffers are not actually allocated
AKAMAI: zfs: CR 3695072
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Issue #6035
It doesn't need to have a loop to free page in a single scatterlist
entry because it should be single or compound page. The pages can be
freed in one invocation to __free_pages() for both cases.
Reviewed-by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Jinshan Xiong <jinshan.xiong@gmail.com>
Closes#6057
In current implementation, only zio buffers in 16KB and bigger are
guaranteed PAGESIZE alignment. This breaks Lustre since it assumes
that 'arc_buf_t::b_data' must be page aligned when zio buffers are
greater than or equal to PAGESIZE.
This patch will make the zio buffers to be PAGESIZE aligned when
the sizes are not less than PAGESIZE.
This change may cause a little bit memory waste but that should be
fine because after ABD is introduced, zio buffers are used to hold
data temporarily and live in memory for a short while.
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jinshan Xiong <jinshan.xiong@gmail.com>
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Closes#6084
All filesystems were converted to dynamically allocated BDIs. The
destruction of backing_dev_info structures is handled as part of
super block destruction. Refactor the code to abstract away the
details of creating and destroying a BDI.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6089
Authored by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Albert Lee <trisk@forkgnu.org>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: bunder2015 <omfgbunder@gmail.com>
OpenZFS-issue: https://www.illumos.org/issues/7786
OpenZFS-commit: http://github.com/openzfs/openzfs/commit/db8498fCloses#6074
Commit 37f9dac removed the zvol_taskq for processing zvol requests.
This was removed as part of switching to make_request_fn and was
motivated by a concern at the time over dispatch latency.
However, this also made all bio request synchronous, and caused
serious performance issues as the bio submitter would wait for
every bio it submitted, effectively making the IO depth 1.
This patch reinstate zvol_taskq, and to make sure overlapped I/Os
are ordered properly, we take range lock in zvol_request, and pass
it along with bio to the I/O functions zvol_{write,discard,read}.
In order to facilitate benchmarks a zvol_request_sync module
option was added to switch between sync and async request handling.
For the moment, the default behavior is synchronous but this is
likely to change pending additional testing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5824
OpenZFS 7252 - compressed zfs send / receive
OpenZFS 7628 - create long versions of ZFS send / receive options
Authored by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: David Quigley <dpquigl@davequigley.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: David Quigley <dpquigl@davequigley.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Ported-by: bunder2015 <omfgbunder@gmail.com>
Ported-by: Don Brady <don.brady@intel.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Most of 7252 was already picked up during ABD work. This
commit represents the gap from the final commit to openzfs.
- Fixed split_large_blocks check in do_dump()
- An alternate version of the write_compressible() function was
implemented for Linux which does not depend on fio. The behavior
of fio differs significantly based on the exact version.
- mkholes was replaced with truncate for Linux.
OpenZFS-issue: https://www.illumos.org/issues/7252
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/5602294Closes#6067
After run a long time with QAT compression, the variable "inst_num"
is overflow by "atomic_inc_32_nv", which causes its neighbor
variable overwritten. Change its definition from U16 to U32.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Weigang Li <weigang.li@intel.com>
Closes#6051
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Prashanth Sreenivasa <pks@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
dbuf_read() creates a zio_root() to track and wait for all the zio's
that may happen as part of this call. However, if the blkptr_t for
this buffer is NULL or a hole, we will not create any more zio's, so
this zio_root() is unnecessary. This is always the case when calling
dbuf_read() on a bonus buffer, because it has no blkptr (it's part of
the containing dnode). For workloads that read a lot of bonus buffers
(e.g. file creation and removal), creating and destroying these
unnecessary zio's can decrease performance by around 3%.
The fix is to only create/destroy the zio_root() in dbuf_read() if the
blkptr is not NULL and not a hole.
Porting Notes:
- The error handling for when dbuf_read_impl() fails which was
originally added in commit 5f6d0b6f5 has been preserved.
OpenZFS-issue: https://www.illumos.org/issues/8025
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/8ec5c7cCloses#6048
Fixup commit 66aca24. We should have equivalent return
values as generic_file_llseek() and advance to end of file.
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Tested-by: bunder2015 <omfgbunder@gmail.com>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Closes#6050Closes#6053
The existing assertions in vdev_label_read() and vdev_label_write(),
testing which config locks are held, are incorrect. The assertions
test for locks which exceed what is required for safety.
Both vdev_label_{read,write}() are changed to assert SCL_STATE is held
as RW_READER or RW_WRITER. This is safe because:
Changes to the vdev tree occur under SCL_ALL as RW_WRITER, via
spa_vdev_enter() and spa_vdev_exit().
Changes to vdev state occur under SCL_STATE_ALL as RW_WRITER, via
spa_vdev_state_enter() and spa_vdev_state_exit().
Therefore, the new assertions guarantee that the vdev cannot change
out from under a zio, and I/O to a specified leaf vdev's label is
safe.
Furthermore, this is consistent with the SPA locking discussion in
spa_misc.c, "For any zio operation that takes an explicit vdev_t
argument ... zio_read_phys(), or zio_write_phys() ... SCL_STATE as
reader suffices."
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5983
Resilver operations frequently cause only a small amount of dirty data
to be written to disk at a time, resulting in the IO scheduler to only
issue 1 write at a time to the resilvering disk. When it is rotational
media the drive will often travel past the next sector to be written
before receiving a write command from ZFS, significantly delaying the
write of the next sector.
Raise zfs_vdev_async_write_min_active so that drives are kept fed
during resilvering.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Issue #4825Closes#5926
Authored by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
sa_find_idx_tab() is declared as taking and returning "void *" parameters.
These can be declared to be the specific types.
OpenZFS-issue: https://www.illumos.org/issues/8061
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4e64affCloses#6017
Authored by: Andriy Gapon <avg@FreeBSD.org>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
When querying ZPL properties verify that the objset is of type
DMU_OST_ZFS.
OpenZFS-issue: https://www.illumos.org/issues/6101
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ce2243aCloses#6015
Force flushing of txg's can be painfully slow when competing for disk
IO, since this is a process meant to execute asynchronously. Optimize
this path via allowing data/hole seeking if the file is clean, but if
dirty fall back to old logic. This is a compromise to disabling the
feature entirely.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Closes#4306Closes#5962
Authored by: Toomas Soome <tsoome@me.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Andrew Stormont <andyjstormont@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Don Brady <don.brady@intel.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- grub-2.02-beta2-422-gcad5cc0 includes support for large blocks.
- Commit 8aab121 allowed GZIP[1-9].
- Grub allows pools with multiple top-level vdevs.
OpenZFS-issue: https://www.illumos.org/issues/5120
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c8811bdCloses#6007
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Approved by: Gordon Ross <gordon.w.ross@gmail.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Enable internal log for DEBUG builds and in zfs-tests.sh.
- callbacks/zfs_dbgmsg.ksh - Dump interal log via kstat.
- callbacks/zfs_dmesg.ksh - Dump dmesg log.
- default.cfg - 'Test Suite Specific Commands' dropped.
OpenZFS-issue: https://www.illumos.org/issues/7503
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/55a1300Closes#6002
In zfs_ereport_post, if an event is a rate limiting
event, immediately return before any processing is done.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#5998
When we try assign a new transaction to a TXG we must know beforehand
if there is sufficient free space on disk. This is to decide,
in dmu_tx_assign(), if we should reject the TX with ENOSPC.
We rely on spa_get_worst_case_asize() to inflate the size of our
logical writes by a factor of spa_asize_inflation which is
calculated as:
(VDEV_RAIDZ_MAXPARITY + 1) * SPA_DVAS_PER_BP * 2 == 24
The problem with the current implementation is that we don't take
into account what happens with very small writes on VDEVs with large
physical block sizes.
Consider the case of writes to a dataset with recordsize=512,
copies=3 on a VDEV with ashift=13 (usually SSD with 8K block size):
every logical IO will end up allocating 3 * 8K = 24K on disk, so 512
bytes multiplied by 48, which is double the size we account for.
If we allow this kind of writes to be assigned a TX it is possible,
when the pool is almost full, to trigger an allocation failure
(ENOSPC) in the ZIO pipeline, which will in turn result in the whole
pool being suspended.
The bug is fixed by using, in spa_get_worst_case_asize(), the MAX()
value chosen between the logical io size from zfs_write() and the
maximum physical block size used among our VDEVs.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#5941
Authored by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Don Brady <don.brady@intel.com>
Ported-by: Matt Ahrens <mahrens@delphix.com>
RAID-Z requires that space be allocated in multiples of P+1 sectors,
because this is the minimum size block that can have the required amount
of parity. Thus blocks on RAIDZ1 must be allocated in a multiple of 2
sectors; on RAIDZ2 multiple of 3; and on RAIDZ3 multiple of 4. A sector
is a unit of 2^ashift bytes, typically 512B or 4KB.
To satisfy this constraint, the allocation size is rounded up to the
proper multiple, resulting in up to 3 "pad sectors" at the end of some
blocks. The contents of these pad sectors are not used, so we do not
need to read or write these sectors. However, some storage hardware
performs much worse (around 1/2 as fast) on mostly-contiguous writes
when there are small gaps of non-overwritten data between the writes.
Therefore, ZFS creates "optional" zio's when writing RAID-Z blocks that
include pad sectors. If writing a pad sector will fill the gap between
two (required) writes, we will issue the optional zio, thus doubling
performance. The gap-filling performance improvement was introduced in
July 2009.
Writing the optional zio is done by the io aggregation code in
vdev_queue.c. The problem is that it is also subject to the limit on
the size of aggregate writes, zfs_vdev_aggregation_limit, which is by
default 128KB. For a given block, if the amount of data plus padding
written to a leaf device exceeds zfs_vdev_aggregation_limit, the
optional zio will not be written, resulting in a ~2x performance
degradation.
The problem occurs only for certain values of ashift, compressed block
size, and RAID-Z configuration (number of parity and data disks). It
cannot occur with the default recordsize=128KB. If compression is
enabled, all configurations with recordsize=1MB or larger will be
impacted to some degree.
The problem notably occurs with recordsize=1MB, compression=off, with 10
disks in a RAIDZ2 or RAIDZ3 group (with 512B or 4KB sectors). Therefore
this problem has been known as "the 1MB 10-wide RAIDZ2 (or 3) problem".
The problem also occurs with the following configurations:
With recordsize=512KB or 256KB, compression=off, the problem occurs only
in rarely-used configurations:
* 4-wide RAIDZ1 with recordsize=512KB and ashift=12 (4KB sectors)
* 4-wide RAIDZ2 (either recordsize, either ashift)
* 5-wide RAIDZ2 with recordsize=512KB (either ashift)
* 6-wide RAIDZ2 with recordsize=512KB (either ashift)
With recordsize=1MB, compression=off, ashift=9 (512B sectors)
* RAIDZ1 with 4 or 8 disks
* RAIDZ2 with 4, 8, or 10 disks
* RAIDZ3 with 6, 8, 9, or 10 disks
With recordsize=1MB, compression=off, ashift=12 (4KB sectors)
* RAIDZ1 with 7 or 8 disks
* RAIDZ2 with 4, 5, or 10 disks
* RAIDZ3 with 6, 9, or 10 disks
With recordsize=2MB and larger (which can only be selected by changing
kernel tunables), many configurations are affected, including with
higher numbers of disks (up to 18 disks with recordsize=2MB).
Increase zfs_vdev_aggregation_limit to allow the optional zio to be
aggregated, thus eliminating the problem. Setting it to 256KB fixes all
commonly-used configurations.
The solution is to aggregate optional zio's regardless of the
aggregation size limit.
Analysis sponsored by Intel Corp.
OpenZFS-issue: https://www.illumos.org/issues/8005
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/321Closes#5931
Authored by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@nexenta.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/2932
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/810e43bCloses#5984Closes#5216
Authored by: George Wilson <george.wilson@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
We don't want to dirty any data when we're in the final txgs of the pool
export logic. This change introduces checks to make sure that no data is
dirtied after a certain point. It also addresses the culprit of this
specific bug – the space map cannot be upgraded when we're in final
stages of pool export. If we encounter a space map that wants to be
upgraded in this phase, then we simply ignore the request as it will get
retried the next time we set the fragmentation metric on that metaslab.
OpenZFS-issue: https://www.illumos.org/issues/8023
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/2ef00f5Closes#5991
On 32-bit platforms spa_state is 32 bits without cast, and thus
caused a NULL pointer dereference when treated as 64bit in
var arg. Accidentally introduced by bcdb96a.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Nathaniel Clark <nathaniel.l.clark@intel.com>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#5966Closes#5965
Authored by: Steven Hartland <steven.hartland@multiplay.co.uk>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Gordon Ross <gordon.w.ross@gmail.com>
When a member of a RAIDZ has been replaced with a device smaller than
the original, then the top level vdev can report its expand size as
16.0E.
The reduced child asize causes the RAIDZ to have a vdev_asize lower than
its vdev_max_asize which then results in an underflow during the
calculation of the parents expand size.
Fix this by updating the vdev_asize if it shrinks, which is already
protected by a check against vdev_min_asize so should always be safe.
Also for RAIDZ vdevs, ensure that the sum of their child vdev_min_asize
is always greater than the parents vdev_min_size.
Reviewed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7885
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/bb0dbaaCloses#5963
* Add ZPOOL pool state to zfs_post_common to
allow differentiation between export and destroy
by zedlets.
* Add pool name as standard export This ensures
pool name is exported to zedlets.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Nathaniel Clark <nathaniel.l.clark@intel.com>
Closes#5942
Wherever possible it's best to avoid depending on a linear ABD.
Update the code accordingly in the following areas.
- vdev_raidz
- zio, zio_checksum
- zfs_fm
- change abd_alloc_for_io() to use abd_alloc()
Reviewed-by: David Quigley <david.quigley@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#5668
df83110 added the ability to specify a custom "ashift" value from the command
line in 'zpool add' and 'zpool attach'. This commit adds additional checks to
the provided ashift to prevent invalid values from being used, which could
result in disastrous consequences for the whole pool.
Additionally provide ASHIFT_MAX and ASHIFT_MIN definitions in spa.h.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#5878
The offset arguments is wrong when changing to abd_copy_off in a6255b7
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5932Closes#5936
For historical reasons zfs_mknode() was written such that it could
never fail. This poses a problem for Linux since zfs_znode_alloc()
could potentually failure due to low memory. Handle this gracefully
by retrying zfs_znode_alloc() until it succeeds, direct reclaim
will eventually be able to allocate memory.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5535Closes#5908
This patch implement the hardware accelerator method in GZIP compression
in ZFS. When the ZFS pool is enabled GZIP compression, the compression
API will be automatically transferred to the hardware accelerator to
free up CPU resource and speed up the compression time.
* To enable Intel QAT hardware acceleration in ZOL you need to have QAT
hardware and the driver installed:
* QAT hardware DH8950:
http://ark.intel.com/products/79483/Intel-QuickAssist-Adapter-8950
* QAT driver:
https://01.org/intel-quickassist-technology
* Start QAT driver in your system:
service qat_service start
* Enable QAT in ZFS, e.g.:
./configure --with-qat=<qat-driver-path>/QAT1.6
make
* Set GZIP compression in ZFS dataset:
zfs set compression = gzip <dataset>
* Get QAT hardware statistics by:
cat /proc/spl/kstat/zfs/qat
* To disable QAT in ZFS:
insmod zfs.ko zfs_qat_disable=1
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Weigang Li <weigang.li@intel.com>
Closes#5846
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Matthew Ahrens <mahrens@delphix.com>
spa_sync() iterates over all the dirty dnodes and processes each of them
by calling dnode_sync(). If there are many dirty dnodes (e.g. because we
created or removed a lot of files), the single thread of spa_sync()
calling dnode_sync() can become a bottleneck. Additionally, if many
dnodes are dirtied concurrently in open context (e.g. due to concurrent
file creation), the os_lock will experience lock contention via
dnode_setdirty().
The solution is to track dirty dnodes on a multilist_t, and for
spa_sync() to use separate threads to process each of the sublists in
the multilist.
OpenZFS-issue: https://www.illumos.org/issues/7968
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4a2a54cCloses#5752
In torvalds/linux@a528d35, there are changes to the getattr family of functions,
struct kstat, and the interface of inode_operations .getattr.
The inode_operations .getattr and simple_getattr() interface changed to:
int (*getattr) (const struct path *, struct dentry *, struct kstat *,
u32 request_mask, unsigned int query_flags)
The request_mask argument indicates which field(s) the caller intends to use.
Fields the caller has not specified via request_mask may be set in the returned
struct anyway, but their values may be approximate.
The query_flags argument indicates whether the filesystem must update
the attributes from the backing store.
Currently both fields are ignored. It is possible that getattr-related
functions within zfs could be optimized based on the request_mask.
struct kstat includes new fields:
u32 result_mask; /* What fields the user got */
u64 attributes; /* See STATX_ATTR_* flags */
struct timespec btime; /* File creation time */
Fields attribute and btime are cleared; the result_mask reflects this. These
appear to be optional based on simple_getattr() and vfs_getattr() within the
kernel, which take the same approach.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5875
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
When we do a clone swap (caused by "zfs rollback" or "zfs receive"), the
ZPL doesn't completely reload the state from the DMU; some values remain
cached in the zfsvfs_t.
OpenZFS-issue: https://www.illumos.org/issues/6874
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/1fdcbd0Closes#5888
Restructure the handling of mount options to be consistent with
upstream OpenZFS. This required making the following changes.
- The zfs_mntopts_t was renamed vfs_t and adjusted to provide
the minimal needed functionality. This includes a pointer
back to the associated zfsvfs_t. Plus it made it possible
to revert zfs_register_callbacks() and zfsvfs_create() back
to their original prototypes.
- A zfs_mnt_t structure was added for the sole purpose of
providing a structure to pass the osname and raw mount
pointer to zfs_domount() without having to copy them.
- Mount option parsing was moved down from the zpl_* wrapper
functions in to the zfs_* functions. This allowed for the
code to be simplied and it's where similar functionality
appears on other platforms.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Several functions were renamed when ZFS was originally ported to
Linux. Revert the code to the original names to minimize the
delta with upstream OpenZFS.
zfs_sb_teardown -> zfsvfs_teardown
zfs_sb_create -> zfsvfs_create
zfs_sb_setup -> zfsvfs_setup
zfs_sb_free -> zfsvfs_free
get_zfs_sb -> getzfsvfs
zfs_sb_hold -> zfsvfs_hold
zfs_sb_rele -> zfsvfs_rele
zfs_sb_prune_aliases -> zfs_prune_aliases (Linux-only)
zfs_sb_prune -> zfs_prune (Linux only)
Align the zfs_vnops.h and zfs_vfsops.h with upstream as much
as possible. Several prototypes were removed and those that
remain were reordered.
Move the EXPORT_SYMBOL lines to the end of the source files
for consistency with the other source files.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The use of zfs_sb_t instead of zfsvfs_t results in unnecessary
conflicts with the upstream source. Change all instances of
zfs_sb_t to zfsvfs_t including updating the variables names.
Whenever possible the code was updated to be consistent with
hope it appears in the upstream OpenZFS source.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The BLKFLSBUF ioctl is expected to do two things:
- flush dirty pages to stable storage, and
- invalidate clean pages
Unfortunately, the existing implementation of BLKFLSBUF in
zvol_ioctl() only flushes pages which are part of the current
TXG to disk. There may be additional dirty pages in the
page cache which haven't yet been submitted to the DMU and
therefore aren't part of any TXG.
Furthermore because zvol_ioctl() returns 0 the generic
blkdev_flushbuf() does not invalidate the page cache.
Resolve the issue by moving bdev_flush() in to zvol_ioctl()
and explicitly waiting for a full TXG sync. Then invalidate
the page cache. The associated ARC buffers need not be
evicted since they cannot be bypassed using O_DIRECT.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5871Closes#5879
Newer versions of cppcheck find the potential NULL pointer
bug in zfs_write(). The function is difficult to refactor without
extensive work, so suppress the potential NULL pointer error
which cannot occur for now.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#5882
The current implementation for allowing nfs to access snapdir is very buggy.
It uses a special fh for snapdirs, such that the next time nfsd does
fh_to_dentry, it actually returns the root inode inside the snapshot. So nfsd
never knows it cross a mountpoint.
The problem is that nfsd will not hold a reference on the vfsmount of the
snapshot. This cause auto unmounter to unmount the snapshot even though nfs is
still holding dentries in it.
To fix this, we return the inode for the snapdirs themselves. However, we also
trigger automount upon fh_to_dentry, and return ESTALE so nfsd will revalidate
and see the mountpoint and do crossmnt.
Because nfsd will now be aware that these are different filesystems users
must add crossmnt to their export options to access snapshot directories.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#3794Closes#4716Closes#5810Closes#5833
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Tim Chase <tim@chase2k.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7867
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/aa1f740dCloses#5874
Properly annotate functions and data section so that objtool does not complain
when CONFIG_STACK_VALIDATION and CONFIG_FRAME_POINTER are enabled.
Pass KERNELCPPFLAGS to assembler.
Use kfpu_begin()/kfpu_end() to protect SIMD regions in Linux kernel.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#5872Closes#5041
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Background information: This assertion about tx_space_* verifies that we
are not dirtying more stuff than we thought we would. We “need” to know
how much we will dirty so that we can check if we should fail this
transaction with ENOSPC/EDQUOT, in dmu_tx_assign(). While the
transaction is open (i.e. between dmu_tx_assign() and dmu_tx_commit() —
typically less than a millisecond), we call dbuf_dirty() on the exact
blocks that will be modified. Once this happens, the temporary
accounting in tx_space_* is unnecessary, because we know exactly what
blocks are newly dirtied; we call dnode_willuse_space() to track this
more exact accounting.
The fundamental problem causing this bug is that dmu_tx_hold_*() relies
on the current state in the DMU (e.g. dn_nlevels) to predict how much
will be dirtied by this transaction, but this state can change before we
actually perform the transaction (i.e. call dbuf_dirty()).
This bug will be fixed by removing the assertion that the tx_space_*
accounting is perfectly accurate (i.e. we never dirty more than was
predicted by dmu_tx_hold_*()). By removing the requirement that this
accounting be perfectly accurate, we can also vastly simplify it, e.g.
removing most of the logic in dmu_tx_count_*().
The new tx space accounting will be very approximate, and may be more or
less than what is actually dirtied. It will still be used to determine
if this transaction will put us over quota. Transactions that are marked
by dmu_tx_mark_netfree() will be excepted from this check. We won’t make
an attempt to determine how much space will be freed by the transaction
— this was rarely accurate enough to determine if a transaction should
be permitted when we are over quota, which is why dmu_tx_mark_netfree()
was introduced in 2014.
We also won’t attempt to give “credit” when overwriting existing blocks,
if those blocks may be freed. This allows us to remove the
do_free_accounting logic in dbuf_dirty(), and associated routines. This
logic attempted to predict what will be on disk when this txg syncs, to
know if the overwritten block will be freed (i.e. exists, and has no
snapshots).
OpenZFS-issue: https://www.illumos.org/issues/7793
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3704e0a
Upstream bugs: DLPX-32883a
Closes#5804
Porting notes:
- DNODE_SIZE replaced with DNODE_MIN_SIZE in dmu_tx_count_dnode(),
Using the default dnode size would be slightly better.
- DEBUG_DMU_TX wrappers and configure option removed.
- Resolved _by_dnode() conflicts these changes have not yet been
applied to OpenZFS.
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7843
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4d519e7Closes#5868
Commit 933ec99 removes read and write from f_op because the vfs layer will
select iter_write or aio_write automatically. However, for Linux <= 4.0,
loop_set_fd will actually check f_op->write and set read-only if not exists.
This patch add them back and use the generic do_sync_{read,write} for
aio_{read,write} and new_sync_{read,write} for {read,write}_iter.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5776Closes#5855
Linux 4.11 introduces a new type, refcount_t, which conflicts with the
type of the same name defined within ZFS.
Rename the ZFS type zfs_refcount_t. Within the ZFS code, use a macro to
cause references to refcount_t to be changed to zfs_refcount_t at
compile time. This reduces conflicts when later landing OpenZFS
patches.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5823Closes#5842
0eef1bde31
introduced some changes which we slightly improved the style of when
porting to illumos.
There is also one minor error-handling fix, in zap_add() the "zap" may
become NULL in case of an error re-opening the ZAP.
Originally suggested at: https://github.com/openzfs/openzfs/pull/276
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#5805
The commit a6255b7fce removed a few
assertions which help catch errors and improve code readability. It also
duplicated two conditionals, which was unnecessary and made the code
confusing to read. This patch cleans it up.
Reviewed-by: David Quigley <david.quigley@intel.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Isaac Huang <he.huang@intel.com>
Closes#5802
Authored by: Daniel Hoffman <dj.hoffman@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
This change removes all gendered language that did not refer specifically
to an individual person or pet. The convention taken was to use
variations on "they" when referring to users and/or human beings, while
using "it" when referring to code, functions, and/or libraries.
Additionally, we took the liberty to fix up any whitespace issues that
were found in any files that were already being modified.
OpenZFS-issue: https://www.illumos.org/issues/7812
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ad626dbCloses#5822
7200 no blocks must be born in a txg after a snaphot is created
Authored by: Andriy Gapon <andriy.gapon@clusterhq.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Approved by: Gordon Ross <gordon.w.ross@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7199
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/bfaed0bCloses#5817
After a hot spare replaces an OFFLINE vdev, the new
parent spare vdev state is set incorrectly to OFFLINE.
The correct state should be DEGRADED. The incorrect
OFFLINE state will prevent top-level vdev from reading
the spare vdev, thus causing unnecessary reconstruction.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Isaac Huang <he.huang@intel.com>
Closes#5766Closes#5770
The global tunable zfs_arc_num_sublists_per_state is used by the ARC and
the dbuf cache, and other users are planned. We should change this
tunable to be common to all multilists. This tuning may be overridden
on a per-multilist basis.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#5764
A likely cut/paste error caused the description to be applied to
zfs_arc_average_blocksize.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#5788
Doing the following command would return success with zfs creating an orphan
object.
touch $(for i in $(seq 256); do printf "n"; done)
The funny thing is that this will only work once for each directory, because
after upgraded to fzap, zfs_lookup would fail properly since it has additional
length check.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5768
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7104
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4b5c8e9Closes#5679
This is a race condition in the deadlist code.
A thread executing an administrative command that uses
dsl_deadlist_space_range() holds the lock of the whole deadlist_t to
protect the access of all its entries that the deadlist contains in an
avl tree.
Sync threads trying to insert a new entry in the deadlist (through
dsl_deadlist_insert() -> dle_enqueue()) do not hold the deadlist lock at
that moment. If the dle_bpobj is the empty bpobj (our sentinel value),
we close and reopen it. Between these two operations, it is possible
for the dsl_deadlist_space_range() thread to dereference that bpobj
which is NULL during that window.
Threads should hold the a deadlist's dl_lock when they manipulate its
internal data so scenarios like the one above are avoided.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#5762
As explicitly stated in section 2 of the 'Programming rules'
comments at the top of zfs_vnops.c.
If you must call iput() within a tx then use zfs_iput_async().
Move iput() calls after dmu_tx_commit() / dmu_tx_abort when
possible. When not possible convert the iput() calls to
zfs_iput_async().
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5758
Add the appropriate compiler flags to accept c99 code. This will help to
minimize differences with upstream, and aid porting changes. One change was
necessary in zvol.c because the DEFINE_IDA() macro does not work with the new
compiler flags.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#5756
When the code was added this tunable was not exposed via module params. Also it
was not documented. This patch changes the type from a uint32 to a ulong as
done with other percentage tunables and also documents it in the
zfs-module-parameters man page.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: David Quigley <david.quigley@intel.com>
Closes#5750
Authored by: Hans Rosenfeld <hans.rosenfeld@nexenta.com>
Reviewed by: Dan Fields <dan.fields@nexenta.com>
Reviewed by: Alek Pinchuk <alek.pinchuk@nexenta.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7448
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/295438bCloses#5737
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7247
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/2ad25b4Closes#5689
Porting notes:
- tests/zfs-tests/tests/functional/cli_root/zfs_receive/zfs_receive_013_pos.ksh
renamed as zfs_receive_015_pos.ksh, zfs_receive_013_pos.ksh is now
used for OpenZFS test.
- libzfs_sendrecv.c: SMALLEST_POSSIBLE_MAX_DDT_MB is always used
for all 32-bit builds.
For generic_write_checks with 2 args, we can exit when it returns zero because
it means count is zero. However this is not the case for generic_write_checks
with 4 args, where zero means no error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Haakan T Johansson <f96hajo@chalmers.se>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5720Closes#5726
This is effectively dead code for the Linux implementation which can
be removed to improve readability. We want to linter to check the
real production/debug build as much as possible.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#5722
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7072
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c39a2aaCloses#5694
Porting notes:
- vdev.c: 'vdev_get_stats' changes are moved to 'vdev_get_stats_ex'.
- vdev_disk.c: ignored, Linux specific code is different.
This patch adds the necessary infrastructure for ABD to make use
of the vectorized fletcher 4 routines.
- export ABD compatible interface from fletcher_4
- add ABD fletcher_4 tests for data and metadata ABD types.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Original-patch-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: David Quigley <david.quigley@intel.com>
Closes#5589
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Porting Notes: Moved reference_tracking_enable and
reference_history outside of ZFS_DEBUG.
OpenZFS-issue: https://www.illumos.org/issues/7545
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4dd77f9Closes#5701
The deadman in ZoL didn't behave quite as it did in upstream
OpenZFS. In addition to the 2 purposes for which OpenZFS used the
zfs_deadman_synctime_ms parameter, ZoL also used it to determine how
frequently the deadman would fire once it has been triggered.
This patch adds the zfs_deadman_checktime_ms parameter to control how
frequently the subsequent checks are performed.
The deadman is now disabled for suspended pools.
As had been the case, unlike upstream OpenZFS, ZoL will not panic when
a hung IO is detected.
The module parameter documentation has been upated to include the new
parameter and to better describe the operation of the deadmen.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#5695
Authored by: Alex Wilson <alex.wilson@joyent.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7019
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/45b1747Closes#5709
Authored by: Alan Somers <asomers@gmail.com>
7115 6922 generates ESC_ZFS_VDEV_REMOVE_AUX a bit too often
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7136
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b72b6bbCloses#5691
Porting notes:
- Functionally this patch behaves the same as the OpenZFS
version but it was adapted because because ZoL doesn't
have the same illumos sysevent_t infrastructure and functionality.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7490
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/6cedfc3Closes#5693
Authored by: Alan Somers <asomers@gmail.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/6922
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/63364b0Closes#5690
Porting notes:
- 'zfs_dbgmsg_print()' reintroduced to userspace.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7277
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/29bdd2fCloses#5684
After resuming a pool the godfather zio could have both the
ZIO_REEXECUTE_NOW and ZIO_REEXECUTE_SUSPEND bits set. This
can occur if some child zios set ZIO_REEXECUTE_NOW while
other set ZIO_REEXECUTE_SUSPEND. The godfather zio can
inherit both flags in zio_notify_parent().
The child zios which assigned the ZIO_REEXECUTE_SUSPEND flag
will be removed from the godfather's child list and added to
the spa->spa_suspend_zio_root child list. While child zios
with the ZIO_REEXECUTE_NOW bit set remain being monitored
by the godfather zio.
When the godfather zio executes zio_done() the presence of
the ZIO_REEXECUTE_SUSPEND bit results in all io_reexecute
being cleared. These child zios will then not be re-executed
and instead will be destroyed and lost.
The most straight forward way to address this situation is
to only clear the ZIO_REEXECUTE_SUSPEND bit and leave the
ZIO_REEXECUTE_NOW bit set.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: yuxiang <guo.yong33@zte.com.cn>
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7580
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3105d95Closes#5678
The .write/.read file operations callbacks can be retired since
support for .read_iter/.write_iter and .aio_read/.aio_write has
been added. The vfs_write()/vfs_read() entry functions will
select the correct interface for the kernel. This is desirable
because all VFS write/read operations now rely on common code.
This change also add the generic write checks to make sure that
ulimits are enforced correctly on write.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5587Closes#5673
metaslab_t:ms_freetree[TXG_SIZE] is only used in syncing context. We
should replace it with two trees: the freeing tree (ranges that we are
freeing this syncing txg) and the freed tree (ranges which have been
freed this txg).
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7613
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/a8698da2Closes#5598
Authored by: Stephen Blinick <stephen.blinick@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Gordon Ross <gordon.w.ross@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7500
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/653af1bCloses#5639
When importing a pool with a large number of filesystems within the same
parent filesystem, we see that dmu_objset_find_dp() takes a long time.
It is called from 3 places: spa_check_logs(), spa_ld_claim_log_blocks(),
and spa_load_verify().
There are several ways to improve performance here:
1. We don't really need to do spa_check_logs() or
spa_ld_claim_log_blocks() if the pool was closed cleanly.
2. spa_load_verify() uses dmu_objset_find_dp() to check that no
datasets have too long of names.
3. dmu_objset_find_dp() is slow because it's doing
zap_value_search() (which is O(N sibling datasets)) to determine
the name of each dsl_dir when it's opened. In this case we
actually know the name when we are opening it, so we can provide
it and avoid the lookup.
This change implements fix#3 from the above list; i.e. make
dmu_objset_find_dp() provide the name of the dataset so that we don't
have to search for it.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prashanth Sreenivasa <prashksp@gmail.com>
Reviewed-by: David Quigley <david.quigley@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7606
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/cac6babCloses#5662
When doing recv and rollback, dsl_dataset_clone_swap_sync_impl will be
called to swap out the ds_objset and do dmu_objset_evict on the old one.
However, currently zv->zv_objset will not be swapped out accordingly, so
if anyone currently holds a fd on the zvol, we risk hitting a use-after-free.
We fix this by introducing the suspend and resume mechanism of zsb to
zv. Before recv or rollback, we use zvol_suspend to block all access to
zv_objset and shut it down. After the recv or rollback, we use zvol_resume
to swap in zv_objset with the new ds_objset and unblock the access.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#4866Closes#5609
Porting notes:
- This issue was first fixed in ZoL by commit d862cb0d. That fix was
then modified and an equivalent version of the patch landed in the
upstream code base. For additional details see the discussion in
https://github.com/openzfs/openzfs/pull/24 .
This commit aligns ZoL with OpenZFS codebase.
Authored by: Andriy Gapon <avg@icyb.net.ua>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Ned Bass <bass6@llnl.gov>
Reviewed by: Tim Chase <tim@chase2k.com>
Approved by: Gordon Ross <gwr@nexenta.com>
Ported-by: George Melikov mail@gmelikov.ru
OpenZFS-issue: https://www.illumos.org/issues/6529
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/e7e978bCloses#5606
Two threads send_traverse_thread() and receive_writer_thread() should
end with thread_exit();
Mostly a cosmetic issue under IllumOS.
Authored by: Jorgen Lundman <lundman@lundman.net>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7659
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/a569268Closes#5603
Authored by: Igor Kozhukhov ikozhukhov@gmail.com
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7071
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/25f7d99Closes#5597
Authored by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7082
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/10e67aaCloses#5596
