1) As implemented the `zpool labelclear` command overwrites
the calculated offsets of all four vdev labels even when only a
single valid label is found. If the device as been re-purposed
but still contains a valid label this can result in space no
longer owned by ZFS being zeroed. Prevent this by verifying
every label removed is intact before it's overwritten.
2) Address a small bug in zpool_do_labelclear() which prevented
labelclear from working on file vdevs. Only block devices support
BLKFLSBUF, try the ioctl() but when it's reported as unsupported
this should not be fatal.
3) Fix `zpool labelclear` so it can be run on vdevs which were
removed from the pool with `zpool remove`. Additionally, allow
intact but partial labels to be cleared as in the case of a failed
`zpool attach` or `zpool replace`.
4) Remove LABELCLEAR and LABELREAD variables for test cases.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8500Closes#8373Closes#6261
This patch attempts to address some user concerns that have arisen
since errata 4 was introduced.
* The errata warning has been made less scary for users without
any encrypted datasets.
* The errata warning now clears itself without a pool reimport if
the bookmark_v2 feature is enabled and no encrypted datasets
exist.
* It is no longer possible to create new encrypted datasets without
enabling the bookmark_v2 feature, thus helping to ensure that the
errata is resolved.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Issue ##8308
Closes#8504
Currently, there is an issue in the raw receive code where
raw receives are allowed to happen on top of previously
non-raw received datasets. This is a problem because the
source-side dataset doesn't know about how the blocks on
the destination were encrypted. As a result, any MAC in
the objset's checksum-of-MACs tree that is a parent of both
blocks encrypted on the source and blocks encrypted by the
destination will be incorrect. This will result in
authentication errors when we decrypt the dataset.
This patch fixes this issue by adding a new check to the
raw receive code. The code now maintains an "IVset guid",
which acts as an identifier for the set of IVs used to
encrypt a given snapshot. When a snapshot is raw received,
the destination snapshot will take this value from the
DRR_BEGIN payload. Non-raw receives and normal "zfs snap"
operations will cause ZFS to generate a new IVset guid.
When a raw incremental stream is received, ZFS will check
that the "from" IVset guid in the stream matches that of
the "from" destination snapshot. If they do not match, the
code will error out the receive, preventing the problem.
This patch requires an on-disk format change to add the
IVset guids to snapshots and bookmarks. As a result, this
patch has errata handling and a tunable to help affected
users resolve the issue with as little interruption as
possible.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8308
The zpool iostat latency histograms (-w) has column names
'sync_queue' and 'async_queue', which do not match the man page, nor
the equivalent columns in average latency. Change the column
names to be 'syncq_wait' and 'asyncq_wait' to be consistent.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#8338
When `zpool iostat` fills the terminal the headers should be
printed again. `zpool iostat -n` can be used to suppress this.
If the command is not attached to a tty, headers will not be
printed so as to not break existing scripts.
Reviewed-by: Joshua M. Clulow <josh@sysmgr.org>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Damian Wojsław <damian@wojslaw.pl>
Closes#8235Closes#8262
Only display the full details of the vdev initialization state
in 'zpool status' output when requested with the -i option.
By default display '(initializing)' after vdevs when they are
being actively initialized. This is consistent with the
established precident of appending '(resilvering), etc' and
fits within the default 80 column terminal width making it
easy to read.
Additionally, updated the 'zpool initialize' documentation to
make it clear the options are mutually exclusive, but allow
duplicate options like all other zfs/zpool commands.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8230
PROBLEM
========
The first access to a block incurs a performance penalty on some platforms
(e.g. AWS's EBS, VMware VMDKs). Therefore we recommend that volumes are
"thick provisioned", where supported by the platform (VMware). This can
create a large delay in getting a new virtual machines up and running (or
adding storage to an existing Engine). If the thick provision step is
omitted, write performance will be suboptimal until all blocks on the LUN
have been written.
SOLUTION
=========
This feature introduces a way to 'initialize' the disks at install or in the
background to make sure we don't incur this first read penalty.
When an entire LUN is added to ZFS, we make all space available immediately,
and allow ZFS to find unallocated space and zero it out. This works with
concurrent writes to arbitrary offsets, ensuring that we don't zero out
something that has been (or is in the middle of being) written. This scheme
can also be applied to existing pools (affecting only free regions on the
vdev). Detailed design:
- new subcommand:zpool initialize [-cs] <pool> [<vdev> ...]
- start, suspend, or cancel initialization
- Creates new open-context thread for each vdev
- Thread iterates through all metaslabs in this vdev
- Each metaslab:
- select a metaslab
- load the metaslab
- mark the metaslab as being zeroed
- walk all free ranges within that metaslab and translate
them to ranges on the leaf vdev
- issue a "zeroing" I/O on the leaf vdev that corresponds to
a free range on the metaslab we're working on
- continue until all free ranges for this metaslab have been
"zeroed"
- reset/unmark the metaslab being zeroed
- if more metaslabs exist, then repeat above tasks.
- if no more metaslabs, then we're done.
- progress for the initialization is stored on-disk in the vdev’s
leaf zap object. The following information is stored:
- the last offset that has been initialized
- the state of the initialization process (i.e. active,
suspended, or canceled)
- the start time for the initialization
- progress is reported via the zpool status command and shows
information for each of the vdevs that are initializing
Porting notes:
- Added zfs_initialize_value module parameter to set the pattern
written by "zpool initialize".
- Added zfs_vdev_{initializing,removal}_{min,max}_active module options.
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: loli10K <ezomori.nozomu@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Signed-off-by: Tim Chase <tim@chase2k.com>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/9102
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c3963210ebCloses#8230
The verbose output of 'zpool list' was not correctly aligned due
to differences in the vdev name lengths. Minimally update the
code the correct the alignment using the same strategy employed
by 'zpool status'.
Missing dashes were added for the empty defaults columns, and
the vdev state is now printed for all vdevs.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7308Closes#8147
This patch adds a new slow I/Os (-s) column to zpool status to show the
number of VDEV slow I/Os. This is the number of I/Os that didn't
complete in zio_slow_io_ms milliseconds. It also adds a new parsable
(-p) flag to display exact values.
NAME STATE READ WRITE CKSUM SLOW
testpool ONLINE 0 0 0 -
mirror-0 ONLINE 0 0 0 -
loop0 ONLINE 0 0 0 20
loop1 ONLINE 0 0 0 0
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7756Closes#6885
Adds a libzutil for utility functions that are common to libzfs and
libzpool consumers (most of what was in libzfs_import.c). This
removes the need for utilities to link against both libzpool and
libzfs.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#8050
Currently, if a resilver is triggered for any reason while an
existing one is running, zfs will immediately restart the existing
resilver from the beginning to include the new drive. This causes
problems for system administrators when a drive fails while another
is already resilvering. In this case, the optimal thing to do to
reduce risk of data loss is to wait for the current resilver to end
before immediately replacing the second failed drive, which allows
the system to operate with two incomplete drives for the minimum
amount of time.
This patch introduces the resilver_defer feature that essentially
does this for the admin without forcing them to wait and monitor
the resilver manually. The change requires an on-disk feature
since we must mark drives that are part of a deferred resilver in
the vdev config to ensure that we do not assume they are done
resilvering when an existing resilver completes.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: @mmaybee
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7732
Historically, zpool status prints "(repairing)" for any drives that
have errors during a scrub:
NAME STATE READ WRITE CKSUM
mypool ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
/tmp/file1 ONLINE 13 0 0 (repairing)
/tmp/file2 ONLINE 0 0 0
/tmp/file3 ONLINE 0 0 0
This was accidentally broken in "OpenZFS 9166 - zfs storage pool
checkpoint" (d2734cc). This patch adds it back in.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7779Closes#7978
Bandwidth and iops are average per second while *_wait are averages
per request for latency or, for queue depths, an instantaneous
measurement at the end of an interval (according to man zpool).
When calculating the first two it makes sense to do
x/interval_duration (x being the increase in total bytes or number of
requests over the duration of the interval, interval_duration in
seconds) to 'scale' from amount/interval_duration to amount/second.
But applying the same math for the latter (*_wait latencies/queue) is
wrong as there is no interval_duration component in the values (these
are time/requests to get to average_time/request or already an
absulute number).
This bug leads to the only correct continuous *_wait figures for both
latencies and queue depths from 'zpool iostat -l/q' being with
duration=1 as then the wrong math cancels itself (x/1 is a nop).
This removes temporal scaling from latency and queue depth figures.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gregor Kopka <gregor@kopka.net>
Closes#7945Closes#7694
This change improve the handling of invalid filesystem properties when
specified at pool creation: this is useful when 'zpool create -n'
(dry run) is executed to detect invalid fs-level options (-O) before
the actual command is run.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7620Closes#7878
Allocation Classes add the ability to have allocation classes in a
pool that are dedicated to serving specific block categories, such
as DDT data, metadata, and small file blocks. A pool can opt-in to
this feature by adding a 'special' or 'dedup' top-level VDEV.
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Reviewed-by: Andreas Dilger <andreas.dilger@chamcloud.com>
Reviewed-by: DHE <git@dehacked.net>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Gregor Kopka <gregor@kopka.net>
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#5182
argv[] gets modified during string parsing for input arguments. This
is reflected in the live process listing. Don't do that.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#7760
= Motivation
While dealing with another performance issue (see 126118f) we noticed
that we spend a lot of time in various places in the kernel when
constructing long nvlists. The problem is that when an nvlist is created
with the NV_UNIQUE_NAME set (which is the case most of the time), we do
a linear search through the whole list to ensure uniqueness for every
entry we add.
An example of the above scenario can be seen in the following
flamegraph, where more than have the time of the zfsdev_ioctl() is spent
on constructing nvlists. Flamegraph:
https://sdimitro.github.io/img/flame/sdimitro_snap_unmount3.svg
Adding a table to speed up lookups will help situations where we just
construct an nvlist (like the scenario above), in addition to regular
lookups and removals.
= What this patch does
In this diff we've implemented a hash-table on top of the nvlist code
that converts most nvlist operations from O(# number of entries) to
O(1)* (the start is for amortized time as the hash-table grows and
shrinks depending on the # of entries - plain lookup is strictly O(1)).
= Performance Analysis
To analyze the performance improvement I just used the setup from the
snapshot deletion issue mentioned above in the Motivation section.
Basically I created 10K filesystems with one snapshot each and then I
just used the API of libZFS_Core to pass down an nvlist of all the
snapshots to have them deleted. The reason I used my own driver program
was to have clean performance results of what actually happens in the
kernel. The flamegraphs and wall clock times mentioned below were
gathered from the start to the end of the driver program's run. Between
trials the testpool used was completely destroyed, the system was
rebooted and the testpool was completely recreated. The reason for this
dance was to get consistent results.
== Results (before patch):
=== Sampling Flamegraphs
[Trial 1] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A.svg
[Trial 2] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A2.svg
[Trial 3] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A3.svg
=== Wall clock times (in seconds)
```
[Trial 4]
real 5.3
user 0.4
sys 2.3
[Trial 5]
real 8.2
user 0.4
sys 2.4
[Trial 6]
real 6.0
user 0.5
sys 2.3
```
== Results (after patch):
=== Sampling Flamegraphs
[Trial 1] https://sdimitro.github.io/img/flame/DLPX-53417/trial-Ae.svg
[Trial 2] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A2e.svg
[Trial 3] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A3e.svg
=== Wall clock times (in seconds)
```
[Trial 4]
real 4.9
user 0.0
sys 0.9
[Trial 5]
real 3.8
user 0.0
sys 0.9
[Trial 6]
real 3.6
user 0.0
sys 0.9
```
== Analysis
The results between the trials are consistent so in this sections I will
only talk about the flamegraph results from trial-1 and the wall-clock
results from trial-4.
From trial-1 we can see that zfs_dev_ioctl() goes from 2,331 to 996
samples counts. Specifically, the samples from fnvlist_add_nvlist() and
spa_history_log_nvl() are almost gone (~500 & ~800 to 5 & 5 samples),
leaving zfs_ioc_destroy_snaps() to dominate most samples from
zfs_dev_ioctl().
From trial-4 we see that the user time dropped to 0 secods. I believe
the consistent 0.4 seconds before my patch was applied was due to my
driver program constructing the long nvlist of snapshots so it can pass
it to the kernel. As for the system time, the effect there is more clear
(2.3 down to 0.9 seconds).
Porting Notes:
* DATA_TYPE_DONTCARE case added to switch in fm_nvprintr() and
zpool_do_events_nvprint().
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9580
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b5eca7b1Closes#7748
Details about the motivation of this feature and its usage can
be found in this blogpost:
https://sdimitro.github.io/post/zpool-checkpoint/
A lightning talk of this feature can be found here:
https://www.youtube.com/watch?v=fPQA8K40jAM
Implementation details can be found in big block comment of
spa_checkpoint.c
Side-changes that are relevant to this commit but not explained
elsewhere:
* renames members of "struct metaslab trees to be shorter without
losing meaning
* space_map_{alloc,truncate}() accept a block size as a
parameter. The reason is that in the current state all space
maps that we allocate through the DMU use a global tunable
(space_map_blksz) which defauls to 4KB. This is ok for metaslab
space maps in terms of bandwirdth since they are scattered all
over the disk. But for other space maps this default is probably
not what we want. Examples are device removal's vdev_obsolete_sm
or vdev_chedkpoint_sm from this review. Both of these have a
1:1 relationship with each vdev and could benefit from a bigger
block size.
Porting notes:
* The part of dsl_scan_sync() which handles async destroys has
been moved into the new dsl_process_async_destroys() function.
* Remove "VERIFY(!(flags & FWRITE))" in "kernel.c" so zhack can write
to block device backed pools.
* ZTS:
* Fix get_txg() in zpool_sync_001_pos due to "checkpoint_txg".
* Don't use large dd block sizes on /dev/urandom under Linux in
checkpoint_capacity.
* Adopt Delphix-OS's setting of 4 (spa_asize_inflation =
SPA_DVAS_PER_BP + 1) for the checkpoint_capacity test to speed
its attempts to fill the pool
* Create the base and nested pools with sync=disabled to speed up
the "setup" phase.
* Clear labels in test pool between checkpoint tests to avoid
duplicate pool issues.
* The import_rewind_device_replaced test has been marked as "known
to fail" for the reasons listed in its DISCLAIMER.
* New module parameters:
zfs_spa_discard_memory_limit,
zfs_remove_max_bytes_pause (not documented - debugging only)
vdev_max_ms_count (formerly metaslabs_per_vdev)
vdev_min_ms_count
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9166
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7159fdb8Closes#7570
1. Add a proc entry to display the pool's state:
$ cat /proc/spl/kstat/zfs/tank/state
ONLINE
This is done without using the spa config locks, so it will
never hang.
2. Fix 'zpool status' and 'zpool list -o health' output to print
"SUSPENDED" instead of "ONLINE" for suspended pools.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7331Closes#7563
We want to be able to pass various settings during import/open of a
pool, which are not only related to rewind. Instead of adding a new
policy and duplicate a bunch of code, we should just rename
rewind_policy to a more generic term like load_policy.
For instance, we'd like to set spa->spa_import_flags from the nvlist,
rather from a flags parameter passed to spa_import as in some cases we
want those flags not only for the import case, but also for the open
case. One such flag could be ZFS_IMPORT_MISSING_LOG (as used in zdb)
which would allow zfs to open a pool when logs are missing.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9235
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/d2b1e44Closes#7532
Some work has been done lately to improve the debugability of the ZFS pool
load (and import) process. This includes:
7638 Refactor spa_load_impl into several functions
8961 SPA load/import should tell us why it failed
7277 zdb should be able to print zfs_dbgmsg's
To iterate on top of that, there's a few changes that were made to make the
import process more resilient and crash free. One of the first tasks during the
pool load process is to parse a config provided from userland that describes
what devices the pool is composed of. A vdev tree is generated from that config,
and then all the vdevs are opened.
The Meta Object Set (MOS) of the pool is accessed, and several metadata objects
that are necessary to load the pool are read. The exact configuration of the
pool is also stored inside the MOS. Since the configuration provided from
userland is external and might not accurately describe the vdev tree
of the pool at the txg that is being loaded, it cannot be relied upon to safely
operate the pool. For that reason, the configuration in the MOS is read early
on. In the past, the two configurations were compared together and if there was
a mismatch then the load process was aborted and an error was returned.
The latter was a good way to ensure a pool does not get corrupted, however it
made the pool load process needlessly fragile in cases where the vdev
configuration changed or the userland configuration was outdated. Since the MOS
is stored in 3 copies, the configuration provided by userland doesn't have to be
perfect in order to read its contents. Hence, a new approach has been adopted:
The pool is first opened with the untrusted userland configuration just so that
the real configuration can be read from the MOS. The trusted MOS configuration
is then used to generate a new vdev tree and the pool is re-opened.
When the pool is opened with an untrusted configuration, writes are disabled
to avoid accidentally damaging it. During reads, some sanity checks are
performed on block pointers to see if each DVA points to a known vdev;
when the configuration is untrusted, instead of panicking the system if those
checks fail we simply avoid issuing reads to the invalid DVAs.
This new two-step pool load process now allows rewinding pools accross
vdev tree changes such as device replacement, addition, etc. Loading a pool
from an external config file in a clustering environment also becomes much
safer now since the pool will import even if the config is outdated and didn't,
for instance, register a recent device addition.
With this code in place, it became relatively easy to implement a
long-sought-after feature: the ability to import a pool with missing top level
(i.e. non-redundant) devices. Note that since this almost guarantees some loss
of data, this feature is for now restricted to a read-only import.
Porting notes (ZTS):
* Fix 'make dist' target in zpool_import
* The maximum path length allowed by tar is 99 characters. Several
of the new test cases exceeded this limit resulting in them not
being included in the tarball. Shorten the names slightly.
* Set/get tunables using accessor functions.
* Get last synced txg via the "zfs_txg_history" mechanism.
* Clear zinject handlers in cleanup for import_cache_device_replaced
and import_rewind_device_replaced in order that the zpool can be
exported if there is an error.
* Increase FILESIZE to 8G in zfs-test.sh to allow for a larger
ext4 file system to be created on ZFS_DISK2. Also, there's
no need to partition ZFS_DISK2 at all. The partitioning had
already been disabled for multipath devices. Among other things,
the partitioning steals some space from the ext4 file system,
makes it difficult to accurately calculate the paramters to
parted and can make some of the tests fail.
* Increase FS_SIZE and FILE_SIZE in the zpool_import test
configuration now that FILESIZE is larger.
* Write more data in order that device evacuation take lonnger in
a couple tests.
* Use mkdir -p to avoid errors when the directory already exists.
* Remove use of sudo in import_rewind_config_changed.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andrew Stormont <andyjstormont@gmail.com>
Approved by: Hans Rosenfeld <rosenfeld@grumpf.hope-2000.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9075
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/619c0123Closes#7459
OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1ebCloses#6900
When the pool is suspended, record whether it was due to an I/O error or
due to MMP writes failing to succeed within the required time.
Change spa_suspended from uint8_t to zio_suspend_reason_t to store the
reason.
When userspace queries pool status via spa_tryimport(), report the
reason the pool was suspended in a new key,
ZPOOL_CONFIG_SUSPENDED_REASON.
In libzfs, when interpreting the returned config nvlist, report
suspension due to MMP with a new pool status enum value,
ZPOOL_STATUS_IO_FAILURE_MMP.
In status_callback(), which generates and emits the message when 'zpool
status' is executed, add a case to print an appropriate message for the
new pool status enum value.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7296
get_format_prompt_string() and zpool_state_to_name() return
a string literal which is read-only, thus they should return
`const char*`.
zpool_get_prop_string() returns a non-const string after
successful nv-lookup, and returns a string literal otherwise.
Since this function is designed to be used for read-only purpose,
the return type should also be `const char*`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#7285
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Don Brady <don.brady@delphix.com>
Ported-by: John Kennedy <john.kennedy@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/7431
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/dfc11533
Porting Notes:
* The CLI long option arguments for '-t' and '-m' don't parse on linux
* Switched from kmem_alloc to vmem_alloc in zcp_lua_alloc
* Lua implementation is built as its own module (zlua.ko)
* Lua headers consumed directly by zfs code moved to 'include/sys/lua/'
* There is no native setjmp/longjump available in stock Linux kernel.
Brought over implementations from illumos and FreeBSD
* The get_temporary_prop() was adapted due to VFS platform differences
* Use of inline functions in lua parser to reduce stack usage per C call
* Skip some ZFS Test Suite ZCP tests on sparc64 to avoid stack overflow
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: DHE <git@dehacked.net>
Closes#7133
The on-disk format for encrypted datasets protects not only
the encrypted and authenticated blocks themselves, but also
the order and interpretation of these blocks. In order to
make this work while maintaining the ability to do raw
sends, the indirect bps maintain a secure checksum of all
the MACs in the block below it along with a few other
fields that determine how the data is interpreted.
Unfortunately, the current on-disk format erroneously
includes some fields which are not portable and thus cannot
support raw sends. It is not possible to easily work around
this issue due to a separate and much smaller bug which
causes indirect blocks for encrypted dnodes to not be
compressed, which conflicts with the previous bug. In
addition, the current code generates incompatible on-disk
formats on big endian and little endian systems due to an
issue with how block pointers are authenticated. Finally,
raw send streams do not currently include dn_maxblkid when
sending both the metadnode and normal dnodes which are
needed in order to ensure that we are correctly maintaining
the portable objset MAC.
This patch zero's out the offending fields when computing
the bp MAC and ensures that these MACs are always
calculated in little endian order (regardless of the host
system's byte order). This patch also registers an errata
for the old on-disk format, which we detect by adding a
"version" field to newly created DSL Crypto Keys. We allow
datasets without a version (version 0) to only be mounted
for read so that they can easily be migrated. We also now
include dn_maxblkid in raw send streams to ensure the MAC
can be maintained correctly.
This patch also contains minor bug fixes and cleanups.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6845Closes#6864Closes#7052
* Remove 'zfs snap' from zfs help message (OpenZFS sync)
* Update zfs(8) to suggest 'snap' can be used as an alias for 'snapshot'
* Enforce 80 columns limit in help messages
* Remove zfs_disable_dup_eviction from zfs-module-parameters(5)
* Expose zfs_scan_max_ext_gap as a kernel module parameter.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7087
usr/src/uts/common/sys/fs/zfs.h
Change ZPROP_INVAL and ZPROP_CONT from macros to enum values. Clang
and GCC both prefer to use unsigned ints to store enums. That was
causing tautological comparison warnings (and likely eliminating
error handling code at compile time) whenever a zfs_prop_t or
zpool_prop_t was compared to ZPROP_INVAL or ZPROP_CONT. Making the
error flags be explicity enum values forces the enum types to be
signed.
ZPROP_INVAL was also compared against two different enum types. I
had to change its name to ZPOOL_PROP_INVAL whenever its compared to
a zpool_prop_t. There are still some places where ZPROP_INVAL or
ZPROP_CONT is compared to a plain int, in code that doesn't know
whether the int is storing a zfs_prop_t or a zpool_prop_t.
usr/src/uts/common/fs/zfs/spa.c
s/ZPROP_INVAL/ZPOOL_PROP_INVAL/
Authored by: Alan Somers <asomers@gmail.com>
Approved by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8652
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c2de80dc74Closes#7061
Resolved unused variable warnings observed after restricting
-Wno-unused-but-set-variable to only libzfs and libzpool.
Reviewed-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6941
Fix a segfault when running 'zpool iostat -v 1' while adding
a VDEV.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6748Closes#6872
Currently, scrubs and resilvers can take an extremely
long time to complete. This is largely due to the fact
that zfs scans process pools in logical order, as
determined by each block's bookmark. This makes sense
from a simplicity perspective, but blocks in zfs are
often scattered randomly across disks, particularly
due to zfs's copy-on-write mechanisms.
This patch improves performance by splitting scrubs
and resilvers into a metadata scanning phase and an IO
issuing phase. The metadata scan reads through the
structure of the pool and gathers an in-memory queue
of I/Os, sorted by size and offset on disk. The issuing
phase will then issue the scrub I/Os as sequentially as
possible, greatly improving performance.
This patch also updates and cleans up some of the scan
code which has not been updated in several years.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Authored-by: Alek Pinchuk <apinchuk@datto.com>
Authored-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#3625Closes#6256
Additionally add four new tests:
* zpool_events_clear: verify 'zpool events -c' functionality
* zpool_events_cliargs: verify command line options and arguments
* zpool_events_follow: verify 'zpool events -f'
* zpool_events_poolname: verify events filtering by pool name
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3285Closes#6762
Added -n flag to zpool reopen that allows a running scrub
operation to continue if there is a device with Dirty Time Log.
By default if a component device has a DTL and zpool reopen
is executed all running scan operations will be restarted.
Added functional tests for `zpool reopen`
Tests covers following scenarios:
* `zpool reopen` without arguments,
* `zpool reopen` with pool name as argument,
* `zpool reopen` while scrubbing,
* `zpool reopen -n` while scrubbing,
* `zpool reopen -n` while resilvering,
* `zpool reopen` with bad arguments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Closes#6076Closes#6746
CID 161388: Resource Leak (REASOURCE_LEAK)
Jump to errout so that file descriptor gets closed before returning
from function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Closes#6755
* PBKDF2 implementation changed to OpenSSL implementation.
* HKDF implementation moved to its own file and tests
added to ensure correctness.
* Removed libzfs's now unnecessary dependency on libzpool
and libicp.
* Ztest can now create and test encrypted datasets. This is
currently disabled until issue #6526 is resolved, but
otherwise functions as advertised.
* Several small bug fixes discovered after enabling ztest
to run on encrypted datasets.
* Fixed coverity defects added by the encryption patch.
* Updated man pages for encrypted send / receive behavior.
* Fixed a bug where encrypted datasets could receive
DRR_WRITE_EMBEDDED records.
* Minor code cleanups / consolidation.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
This change incorporates three major pieces:
The first change is a keystore that manages wrapping
and encryption keys for encrypted datasets. These
commands mostly involve manipulating the new
DSL Crypto Key ZAP Objects that live in the MOS. Each
encrypted dataset has its own DSL Crypto Key that is
protected with a user's key. This level of indirection
allows users to change their keys without re-encrypting
their entire datasets. The change implements the new
subcommands "zfs load-key", "zfs unload-key" and
"zfs change-key" which allow the user to manage their
encryption keys and settings. In addition, several new
flags and properties have been added to allow dataset
creation and to make mounting and unmounting more
convenient.
The second piece of this patch provides the ability to
encrypt, decyrpt, and authenticate protected datasets.
Each object set maintains a Merkel tree of Message
Authentication Codes that protect the lower layers,
similarly to how checksums are maintained. This part
impacts the zio layer, which handles the actual
encryption and generation of MACs, as well as the ARC
and DMU, which need to be able to handle encrypted
buffers and protected data.
The last addition is the ability to do raw, encrypted
sends and receives. The idea here is to send raw
encrypted and compressed data and receive it exactly
as is on a backup system. This means that the dataset
on the receiving system is protected using the same
user key that is in use on the sending side. By doing
so, datasets can be efficiently backed up to an
untrusted system without fear of data being
compromised.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#494Closes#5769
OpenZFS provides a library called tpool which implements thread
pools for user space applications. Porting this library means
the zpool utility no longer needs to borrow the kernel mutex and
taskq interfaces from libzpool. This code was updated to use
the tpool library which behaves in a very similar fashion.
Porting libtpool was relatively straight forward and minimal
modifications were needed. The core changes were:
* Fully convert the library to use pthreads.
* Updated signal handling.
* lmalloc/lfree converted to calloc/free
* Implemented portable pthread_attr_clone() function.
Finally, update the build system such that libzpool.so is no
longer linked in to zfs(8), zpool(8), etc. All that is required
is libzfs to which the zcommon soures were added (which is the way
it always should have been). Removing the libzpool dependency
resulted in several build issues which needed to be resolved.
* Moved zfeature support to module/zcommon/zfeature_common.c
* Moved ratelimiting to to module/zfs/zfs_ratelimit.c
* Moved get_system_hostid() to lib/libspl/gethostid.c
* Removed use of cmn_err() in zcommon source
* Removed dprintf_setup() call from zpool_main.c and zfs_main.c
* Removed highbit() and lowbit()
* Removed unnecessary library dependencies from Makefiles
* Removed fletcher-4 kstat in user space
* Added sha2 support explicitly to libzfs
* Added highbit64() and lowbit64() to zpool_util.c
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6442
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Sen Haerens <sen@senhaerens.be>
Closes#6444Closes#6445
Turning the multihost property on requires that a hostid be set to allow
ZFS to determine when a foreign system is attemping to import a pool.
The error message instructing the user to set a hostid refers to
genhostid(1).
Genhostid(1) is not available on SUSE Linux. This commit adds a script
modeled after genhostid(1) for those users.
Zgenhostid checks for an /etc/hostid file; if it does not exist, it
creates one and stores a value. If the user has provided a hostid as an
argument, that value is used. Otherwise, a random hostid is generated
and stored.
This differs from the CENTOS 6/7 versions of genhostid, which overwrite
the /etc/hostid file even though their manpages state otherwise.
A man page for zgenhostid is added. The one for genhostid is in (1), but
I put zgenhostid in (8) because I believe it's more appropriate.
The mmp tests are modified to use zgenhostid to set the hostid instead
of using the spl_hostid module parameter. zgenhostid will not replace
an existing /etc/hostid file, so new mmp_clear_hostid calls are
required.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6358Closes#6379
CID 165757: Control flow issues (MISSING_BREAK)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#6348
Add multihost=on|off pool property to control MMP. When enabled
a new thread writes uberblocks to the last slot in each label, at a
set frequency, to indicate to other hosts the pool is actively imported.
These uberblocks are the last synced uberblock with an updated
timestamp. Property defaults to off.
During tryimport, find the "best" uberblock (newest txg and timestamp)
repeatedly, checking for change in the found uberblock. Include the
results of the activity test in the config returned by tryimport.
These results are reported to user in "zpool import".
Allow the user to control the period between MMP writes, and the
duration of the activity test on import, via a new module parameter
zfs_multihost_interval. The period is specified in milliseconds. The
activity test duration is calculated from this value, and from the
mmp_delay in the "best" uberblock found initially.
Add a kstat interface to export statistics about Multiple Modifier
Protection (MMP) updates. Include the last synced txg number, the
timestamp, the delay since the last MMP update, the VDEV GUID, the VDEV
label that received the last MMP update, and the VDEV path. Abbreviated
output below.
$ cat /proc/spl/kstat/zfs/mypool/multihost
31 0 0x01 10 880 105092382393521 105144180101111
txg timestamp mmp_delay vdev_guid vdev_label vdev_path
20468 261337 250274925 68396651780 3 /dev/sda
20468 261339 252023374 6267402363293 1 /dev/sdc
20468 261340 252000858 6698080955233 1 /dev/sdx
20468 261341 251980635 783892869810 2 /dev/sdy
20468 261342 253385953 8923255792467 3 /dev/sdd
20468 261344 253336622 042125143176 0 /dev/sdab
20468 261345 253310522 1200778101278 2 /dev/sde
20468 261346 253286429 0950576198362 2 /dev/sdt
20468 261347 253261545 96209817917 3 /dev/sds
20468 261349 253238188 8555725937673 3 /dev/sdb
Add a new tunable zfs_multihost_history to specify the number of MMP
updates to store history for. By default it is set to zero meaning that
no MMP statistics are stored.
When using ztest to generate activity, for automated tests of the MMP
function, some test functions interfere with the test. For example, the
pool is exported to run zdb and then imported again. Add a new ztest
function, "-M", to alter ztest behavior to prevent this.
Add new tests to verify the new functionality. Tests provided by
Giuseppe Di Natale.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#745Closes#6279
Currently, there is no way to pause a scrub. Pausing may
be useful when the pool is busy with other I/O to preserve
bandwidth.
This patch adds the ability to pause and resume scrubbing.
This is achieved by maintaining a persistent on-disk scrub state.
While the state is 'paused' we do not scrub any more blocks.
We do however perform regular scan housekeeping such as
freeing async destroyed and deadlist blocks while paused.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Serapheim Dimitropoulos <serapheimd@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6167
This prints dashes instead of zeros for zero latency values in
'zpool iostat -p'. You'll get zero latencies reported when the
disk is idle, but technically a zero latency is invalid, since you
can't measure the latency of doing nothing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6210
Users can now provide their own scripts to be run
with 'zpool iostat/status -c'. User scripts should be
placed in ~/.zpool.d to be included in zpool's
default search path.
Provide a script which can be used with
'zpool iostat|status -c' that will return the type of
device (hdd, sdd, file).
Provide a script to get various values from smartctl
when using 'zpool iostat/status -c'.
Allow users to define the ZPOOL_SCRIPTS_PATH
environment variable which can be used to override
the default 'zpool iostat/status -c' search path.
Allow the ZPOOL_SCRIPTS_ENABLED environment
variable to enable or disable 'zpool status/iostat -c'
functionality.
Use the new smart script to provide the serial command.
Install /etc/sudoers.d/zfs file which contains the sudoer
rule for smartctl as a sample.
Allow 'zpool iostat/status -c' tests to run in tree.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6121Closes#6153
This addition will enable us to sync an open TXG to the main pool
on demand. The functionality is similar to 'sync(2)' but 'zpool sync'
will return when data has hit the main storage instead of potentially
just the ZIL as is the case with the 'sync(2)' cmd.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6122
This patch adds a '-f' option to 'zpool offline' to fault a vdev
instead of bringing it offline. Unlike the OFFLINE state, the
FAULTED state will trigger the FMA code, allowing for things like
autoreplace and triggering the slot fault LED. The -f faults
persist across imports, unless they were set with the temporary
(-t) flag. Both persistent and temporary faults can be cleared
with zpool clear.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6094
CID 161638: Resource leak (RESOURCE_LEAK)
Ensure the string array in print_zpool_script_help
is freed in cases when there is an error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6111
This commit allow higher ashift values (up to 16) in 'zpool create'
The ashift value was previously limited to 13 (8K block) in b41c990
because the limited number of uberblocks we could fit in the
statically sized (128K) vdev label ring buffer could prevent the
ability the safely roll back a pool to recover it.
Since b02fe35 the largest uberblock size we support is 8K: this
allow us to store a minimum number of 16 uberblocks in the vdev
label, even with higher ashift values.
Additionally change 'ashift' pool property behaviour: if set it will
be used as the default hint value in subsequent vdev operations
('zpool add', 'attach' and 'replace'). A custom ashift value can still
be specified from the command line, if desired.
Finally, fix a bug in add-o_ashift.ksh caused by a missing variable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2024Closes#4205Closes#4740Closes#5763
* Add zfs_nicebytes() to print human-readable sizes
Some 'zfs', 'zpool' and 'zdb' output strings can be confusing to the
user when no units are specified. This add a new zfs_nicenum_format
"ZFS_NICENUM_BYTES" used to print bytes in their human-readable form.
Additionally, update some test cases to use machine-parsable 'zfs get'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2414Closes#3185Closes#3594Closes#6032
This patch updates the "zpool status/iostat -c" commands to only run
"pre-baked" scripts from the /etc/zfs/zpool.d directory (or wherever
you install to). The scripts can only be run from -c as an unprivileged
user (unless the ZPOOL_SCRIPTS_AS_ROOT environment var is
set by root). This was done to encourage scripts to be written is such
a way that normal users can use them, and to be cautious. If your
script needs to run a privileged command, consider adding the
appropriate line in /etc/sudoers. See zpool(8) for an example of how
to do this.
The patch also allows the scripts to output custom column names. If
the script outputs a line like:
name=value
then "name" is used for the column name, and "value" is its value.
Multiple columns can be specified by outputting multiple lines. Column
names and values can have spaces. If the value is empty, a dash (-) is
printed instead.
After all the "name=value" lines are read (if any), zpool will take the
next the next line of output (if any) and print it without a column
header. After that, no more lines will be processed. This can be
useful for printing errors.
Lastly, this patch also disables the -c option with the latency and
request size histograms, since it produced awkward output and made the
code harder to maintain.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5852
Be sure to invalidate a vdev's cache before performing
a zpool labelclear. There are cases where the cache is
stale because we did some operation that bypassed it,
and since we are doing an open with only O_RDWR, we
should invalidate it to be safe.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6009
Authored by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Updated 'zpool labelclear' and 'zdb -l' such that they attempt
to find a vdev given solely its short name. This behavior is
consistent with the upstream OpenZFS code and the test cases
depend on it. The actual implementation differs slightly due
to device naming conventions on Linux.
- auto_online_001_pos, auto_replace_001_pos and add-o_ashift
test cases updated to expect failure when no label exists.
- read_efi_label() and zpool_label_disk_check() are read-only
operations and should use O_RDONLY at open time to enforce this.
- zpool_label_disk() and zpool_relabel_disk() write the partition
information using O_DIRECT an fsync() and page cache invalidation
to ensure a consistent view of the device.
- dump_label() in zdb should invalidate the page cache in order
to get the authoritative label from disk.
OpenZFS-issue: https://www.illumos.org/issues/6865
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c95076cCloses#5981
When a pool is suspended it's impossible to read the list
of damaged files from disk. This would result in a generic
misleading "insufficient permissions" error message.
Update zpool_get_errlog() to use the standard zpool error
logging functions to generate a useful error message. In
this case:
errors: List of errors unavailable: pool I/O is currently suspended
This patch does not address the related issue of potentially
not being able to resume a suspend pool when the underlying
device names have changed.
Additionally, remove the error handling from zfs_alloc()
in zpool_get_errlog() for readability since this function
can never fail.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4031Closes#5731Closes#5907
Porting Notes:
- Many of the fixes proposed by this patch were already applied.
In the cases where a different but equivalent fix was made the
code was updated with the OpenZFS version to minimize differences.
- The zpool_get_vdev_by_name() function was previously removed
by commit 235db0a.
Authored by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andy Stormont <astormont@racktopsystems.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Haakan T Johansson <f96hajo@chalmers.se>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6551
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b327cd3Closes#5590
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5547Closes#5543
zpool iostat allows you to specify only certain vdevs to display.
Currently, if you run 'zpool iostat -c CMD vdev1 vdev2 ...'
on specific vdevs, it will actually run the command on *all* vdevs,
and just display the results for the vdevs you specify. This patch
corrects the behavior to only run the command on the specified vdevs,
and also enables the zpool_iostat_005_pos.ksh tests.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5443
Enable picky cstyle checks and resolve the new warnings. The vast
majority of the changes needed were to handle minor issues with
whitespace formatting. This patch contains no functional changes.
Non-whitespace changes are as follows:
* 8 times ; to { } in for/while loop
* fix missing ; in cmd/zed/agents/zfs_diagnosis.c
* comment (confim -> confirm)
* change endline , to ; in cmd/zpool/zpool_main.c
* a number of /* BEGIN CSTYLED */ /* END CSTYLED */ blocks
* /* CSTYLED */ markers
* change == 0 to !
* ulong to unsigned long in module/zfs/dsl_scan.c
* rearrangement of module_param lines in module/zfs/metaslab.c
* add { } block around statement after for_each_online_node
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5465
Do not force VDEV_NAME_TYPE_ID in max_width(), instead add it
in the relevant calls to max_width().
The first location of max_width() where VDEV_NAME_TYPE_ID is
now added in show_import() is followed by print_import_config() and
print_logs(). Both these print children vdev names that have been
retrieved using an explicit VDEV_NAME_TYPE_ID added.
The second location is in status_callback(). This is followed by
print_status_config(), print_logs(), print_l2cache(), and
print_spares(). For l2cache and spares it should not matter as there
are no mirror-X or raidz-X involved. print_status_config() as above
retrieves the name using explicit VDEV_NAME_TYPE_ID before
calling itself to print children.
The call of max_width() in get_namewidth() is not changed, as this is
used by zpool_do_iostat(), followed by print_iostat(), which does not
add VDEV_NAME_TYPE_ID.
Overall, we should consider adding VDEV_NAME_TYPE_ID to the
relevant name_flags / cb_name_flags fields, and remove the explicit
adding in called routines.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5401
This patch adds a command (-c) option to zpool status and zpool iostat. The
-c option allows you to run an arbitrary command on each vdev and display
the first line of output in zpool status/iostat. The environment vars
VDEV_PATH and VDEV_UPATH are set to the vdev's path and "underlying path"
before running the command. For device mapper, multipath, or partitioned
vdevs, VDEV_UPATH is the actual underlying /dev/sd* disk. This can be useful
if the command you're running requires a /dev/sd* device.
The patch also uses /sys/block/<dev>/slaves/ to lookup the underlying device
instead of using libdevmapper. This not only removes the libdevmapper
requirement at build time, but also allows you to resolve device mapper
devices without being root. This means that UDEV_UPATH get set correctly
when running zpool status/iostat as an unprivileged user.
Example:
$ zpool status -c 'echo I am $VDEV_PATH, $VDEV_UPATH'
NAME STATE READ WRITE CKSUM
mypool ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
mpatha ONLINE 0 0 0 I am /dev/mapper/mpatha, /dev/sdc
sdb ONLINE 0 0 0 I am /dev/sdb1, /dev/sdb
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5368
Sometimes it is desirable to specifically disable one or several
features directly on the 'zpool create' command line.
$ zpool create -o feature@<feature>=disabled ...
Original-patch-by: Turbo Fredriksson <turbo@bayour.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3460Closes#5142Closes#5324
First rename spare_cbdata_t cb -> spare_cb in print_status_config(),
to free up cb.
Using the structure removes the explicit parameters namewidth
and name_flags from several functions. Also use status_cbdata_t
for print_import_config(). This simplifies print_logs().
Remove the parameter 'verbose' for print_logs(). It does not really
mean verbose, it selected between the print_status_config and
print_import_config() paths. This selection is now done by
cb_print_config of spare_cbdata_t.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Håkan Johansson <f96hajo@chalmers.se>
Closes#5259
This first phase brings over the ZFS SLM module, zfs_mod.c, to handle
auto operations in response to disk events. Disk event monitoring is
provided from libudev and generates the expected payload schema for
zfs_mod. This work leverages the recently added devid and phys_path
strings in the vdev label.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#4673
ZFS allows for specific permissions to be delegated to normal users
with the `zfs allow` and `zfs unallow` commands. In addition, non-
privileged users should be able to run all of the following commands:
* zpool [list | iostat | status | get]
* zfs [list | get]
Historically this functionality was not available on Linux. In order
to add it the secpolicy_* functions needed to be implemented and mapped
to the equivalent Linux capability. Only then could the permissions on
the `/dev/zfs` be relaxed and the internal ZFS permission checks used.
Even with this change some limitations remain. Under Linux only the
root user is allowed to modify the namespace (unless it's a private
namespace). This means the mount, mountpoint, canmount, unmount,
and remount delegations cannot be supported with the existing code. It
may be possible to add this functionality in the future.
This functionality was validated with the cli_user and delegation test
cases from the ZFS Test Suite. These tests exhaustively verify each
of the supported permissions which can be delegated and ensures only
an authorized user can perform it.
Two minor bug fixes were required for test-running.py. First, the
Timer() object cannot be safely created in a `try:` block when there
is an unconditional `finally` block which references it. Second,
when running as a normal user also check for scripts using the
both the .ksh and .sh suffixes.
Finally, existing users who are simulating delegations by setting
group permissions on the /dev/zfs device should revert that
customization when updating to a version with this change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#362Closes#434Closes#4100Closes#4394Closes#4410Closes#4487
This is a purely cosmetical change, to consistently prefer one of
two (both acceptable) choises for the word parsable in documentation and
code. I don't really care which to use, but acording to wiktionary
https://en.wiktionary.org/wiki/parsable#English parsable is preferred.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4682
Add argument format to print_one_column(), and use it to call
zfs_nicenum_format with, instead of just zfs_nicenum. Don't print "%"
for fragmentation or capacity percent values.
The calls to print_one_colum is made with ZFS_NICENUM_RAW if
cb->cb_literal (zpool list called with -p), and ZFS_NICENUM_1024 if not.
Also zpool_get_prop is modified to don't add "%" or "x" if literal.
Signed-off-by: Christer Ekholm <che@chrekh.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov
Closes#4657
3993 zpool(1M) and zfs(1M) should support -p for "list" and "get"
4700 "zpool get" doesn't support -H or -o options
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/3993
OpenZFS-issue: https://www.illumos.org/issues/4700
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c58b352
Porting notes:
I removed ZoL's zpool_get_prop_literal() in favor of
zpool_get_prop(..., boolean_t literal) since that's what OpenZFS
uses. The functionality is the same.
5669 altroot not set in zpool create when specified with -o
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/5669
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c423721Closes#4594
6659 nvlist_free(NULL) is a no-op
Reviewed by: Toomas Soome <tsoome@me.com>
Reviewed by: Marcel Telka <marcel@telka.sk>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/6659https://github.com/illumos/illumos-gate/commit/aab83bb
Ported-by: David Quigley <dpquigl@davequigley.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4566
When partitioning a device a name may be specified for each partition.
Internally zfs doesn't use this partition name for anything so it
has always just been set to "zfs".
However this isn't optimal because udev will create symlinks using
this name in /dev/disk/by-partlabel/. If the name isn't unique
then all the links cannot be created.
Therefore a random 64-bit value has been added to the partition
label, i.e "zfs-1234567890abcdef". Additional information could
be encoded here but since partitions may be reused that might
result in confusion and it was decided against.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#4517
This issue was caused by calling `thread_init()` and `thread_fini()`
multiple times resulting in `kthread_key` being invalid. To resolve
the issue the explicit calls to `thread_init()` and `thread_fini()`
required by the `zpool` command have been moved in to the command.
Consumers such as `zdb` and `zhack` perform the same initialized
through `kernel_init()` and `kernel_fini()`.
Resolving this issue allows multiple additional test cases to
be enabled.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#4331
Historically libblkid support was detected as part of configure
and optionally enabled. This was done because at the time support
for detecting ZFS pool vdevs had just be added to libblkid and
those updated packages were not yet part of many distributions.
This is no longer the case and any reasonably current distribution
will ship a version of libblkid which can detect ZFS pool vdevs.
This patch makes libblkid mandatory at build time and libblkid
the preferred method of scanning for ZFS pools. For distributions
which include a modern version of libblkid there is no change in
behavior. Explicitly scanning the default search paths is still
supported and can be enabled with the '-s' command line option.
Additionally making libblkid mandatory means that the 'zpool create'
command can reliably detect if a specified device has an existing
non-ZFS filesystem (ext4, xfs) and print a warning.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2448
Commit d2f3e29 introduced the -p option which outputs full paths
for vdevs to multiple zpool subcommands. When this was merged
there was no conflict for this flag letter. However it's certain
there will be a conflict with the -p (parsable) flag used by other
subcommands. Therefore, -p is being changed to -P to avoid this.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4368
The following options have been added to the zpool add, iostat,
list, status, and split subcommands. The default behavior was
not modified, from zfs(8).
-g Display vdev GUIDs instead of the normal short
device names. These GUIDs can be used in-place of
device names for the zpool detach/off‐
line/remove/replace commands.
-L Display real paths for vdevs resolving all symbolic
links. This can be used to lookup the current block
device name regardless of the /dev/disk/ path used
to open it.
-p Display full paths for vdevs instead of only the
last component of the path. This can be used in
conjunction with the -L flag.
This behavior may also be enabled using the following environment
variables.
ZPOOL_VDEV_NAME_GUID
ZPOOL_VDEV_NAME_FOLLOW_LINKS
ZPOOL_VDEV_NAME_PATH
This change is based on worked originally started by Richard Yao
to add a -g option. Then extended by @ilovezfs to add a -L option
for openzfsonosx. Those changes have been merged, re-factored,
a -p option added and extended to all relevant zpool subcommands.
Original-patch-by: Richard Yao <ryao@gentoo.org>
Extended-by: ilovezfs <ilovezfs@icloud.com>
Extended-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: ilovezfs <ilovezfs@icloud.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2011Closes#4341
5767 fix several problems with zfs test suite
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Gordon Ross <gwr@nexenta.com>
References:
https://www.illumos.org/issues/5767https://github.com/illumos/illumos-gate/commit/52244c0
Porting Notes:
- Only the updates to zpool_main.c were kept because the ZFS test
suite is not currently part of the ZoL source tree. The test
suite itself should be updated to include the latest versions
of the tests once we're running it for every commit
- Fixes `zpool list` output.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
5959 clean up per-dataset feature count code
Reviewed by: Toomas Soome <tsoome@me.com>
Reviewed by: George Wilson <george@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/5959https://github.com/illumos/illumos-gate/commit/ca0cc39
Porting notes:
illumos code doesn't check for feature_get_refcount() returning
ENOTSUP (which means feature is disabled) in zdb. zfsonlinux added
a check in https://github.com/zfsonlinux/zfs/commit/784652c
due to #3468. The check was reintroduced here.
Ported-by: Witaut Bajaryn <vitaut.bayaryn@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3965
All other sections use a tab, which makes them easy to parse. Only the
"scan:" section had its continuation lines indented with four spaces.
This makes them consistent with the others.
Signed-off-by: Remy Blank <remy.blank@pobox.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#3769
4966 zpool list iterator does not update output
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
https://github.com/illumos/illumos-gate/commit/cd67d23https://www.illumos.org/issues/4966
Ported-by: kernelOfTruth kerneloftruth@gmail.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3566
sysstat's iostat omits the first report when the -y option is used.
This patch adds that functionality and omits the first report with
statistics since system boot.
Signed-off-by: Hajo Möller <dasjoe@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3439
All fprintf() error messages are moved out of the libzfs_init()
library function where they never belonged in the first place. A
libzfs_error_init() function is added to provide useful error
messages for the most common causes of failure.
Additionally, in libzfs_run_process() the 'rc' variable was renamed
to 'error' for consistency with the rest of the code base.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Support exporting all imported pools in one go, using 'zpool export -a'.
This is accomplished by moving the export parts from zpool_do_export()
in to the new function zpool_export_one(). The for_each_pool() function
is used to enumerate the list of pools to be exported. Passing an argc
of 0 implies the function should be called on all pools.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #3203
5134 if ZFS_DEBUG or debug= is set, libzpool should enable debug prints
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Saso Kiselkov <skiselkov.ml@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/projects/illumos-gate/issues/5134https://github.com/illumos/illumos-gate/commit/7fa49ea
Porting notes:
Added dprintf_setup() to main in zfs_main.c and zpool_main.c.
Ported by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2669
In dry run mode, zpool should display more of the proposed pool
configuration for "zpool add". This commit adds support for displaying
cache devices.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1106
If spl_hostid is set via module parameter, it's likely different from
gethostid(). Therefore, the userspace tool should read it first before
falling back to gethostid().
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3034
Commit c66989b accidentally introduced a cstyle issue which went
unnoticed. This tiny patch corrects that oversight.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
In userland we need to switch over to the temporary name once the
pool has been created, otherwise the root dataset won't mount
and the error "cannot open 'the_real_name': dataset does not exist"
is printed.
Signed-off-by: ilovezfs <ilovezfs@icloud.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2760
Change the zpool program to skip its hostid mismatch check in the
same way that libzfs already does.
Invoked imports fail if the ZPOOL_CONFIG_HOSTID nvpair is missing in
the /etc/zfs/zpool.cache file, which can happen as of the /etc/hostid
deprecation in commit zfsonlinux/spl@acf0ade362.
Signed-off-by: Darik Horn <dajhorn@vanadac.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2794
Creating virtual machines that have their rootfs on ZFS on hosts that
have their rootfs on ZFS causes SPA namespace collisions when the
standard name rpool is used. The solution is either to give each guest
pool a name unique to the host, which is not always desireable, or boot
a VM environment containing an ISO image to install it, which is
cumbersome.
26b42f3f9d introduced `zpool import -t
...` to simplify situations where a host must access a guest's pool when
there is a SPA namespace conflict. We build upon that to introduce
`zpool import -t tname ...`. That allows us to create a pool whose
in-core name is tname, but whose on-disk name is the normal name
specified.
This simplifies the creation of machine images that use a rootfs on ZFS.
That benefits not only real world deployments, but also ZFSOnLinux
development by decreasing the time needed to perform rootfs on ZFS
experiments.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2417
zpool import's -t parameter is intended for use with -R when operating
on pools that belong to other systems. Like -R, pools imported in this
way should not update the cachefile unless explicitly requested. The
initial implementation allowed the cachefile to be updated when -R was
not used. This went uncaught during testing because -R had implicitly
disabled use of the cachefile.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2417
Adding to a property list only if there is no existing value is used
twice. Once by zpool create -R and again by zpool import -R. Now that
zpool create -t and zpool import -t also need it, lets refactor it into
a helper function to make the code more readable.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2417
The 'zpool list -v' command displays lots of info but excludes the
capacity of each disk. This should be added.
5147 zpool list -v should show individual disk capacity
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Matthew Ahrens <matthew.ahrens@delphix.com>
Reviewed by: Richard Elling <richard.elling@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/5147https://github.com/illumos/illumos-gate/commit/7a09f97
Ported by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2688
Change mount code to diagnose filesystem versions that
are not supported by the current implementation.
Change upgrade code to do likewise and refuse to upgrade
a pool if any filesystems on it are a version which is
not supported by the current implementation.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Dan Swartzendruber <dswartz@druber.com>
Closes: #2616
4970 need controls on i/o issued by zpool import -XF
4971 zpool import -T should accept hex values
4972 zpool import -T implies extreme rewind, and thus a scrub
4973 spa_load_retry retries the same txg
4974 spa_load_verify() reads all data twice
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/4970https://www.illumos.org/issues/4971https://www.illumos.org/issues/4972https://www.illumos.org/issues/4973https://www.illumos.org/issues/4974https://github.com/illumos/illumos-gate/commit/e42d205
Notes:
This set of patches adds a set of tunable parameters for the
"extreme rewind" mode of pool import which allows control over
the traversal performed during such an import.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2598
4976 zfs should only avoid writing to a failing non-redundant top-level vdev
4978 ztest fails in get_metaslab_refcount()
4979 extend free space histogram to device and pool
4980 metaslabs should have a fragmentation metric
4981 remove fragmented ops vector from block allocator
4982 space_map object should proactively upgrade when feature is enabled
4983 need to collect metaslab information via mdb
4984 device selection should use fragmentation metric
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
https://www.illumos.org/issues/4976https://www.illumos.org/issues/4978https://www.illumos.org/issues/4979https://www.illumos.org/issues/4980https://www.illumos.org/issues/4981https://www.illumos.org/issues/4982https://www.illumos.org/issues/4983https://www.illumos.org/issues/4984https://github.com/illumos/illumos-gate/commit/2e4c998
Notes:
The "zdb -M" option has been re-tasked to display the new metaslab
fragmentation metric and the new "zdb -I" option is used to control
the maximum number of in-flight I/Os.
The new fragmentation metric is derived from the space map histogram
which has been rolled up to the vdev and pool level and is presented
to the user via "zpool list".
Add a number of module parameters related to the new metaslab weighting
logic.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2595
4171 clean up spa_feature_*() interfaces
4172 implement extensible_dataset feature for use by other zpool features
Reviewed by: Max Grossman <max.grossman@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Approved by: Garrett D'Amore <garrett@damore.org>a
References:
https://www.illumos.org/issues/4171https://www.illumos.org/issues/4172https://github.com/illumos/illumos-gate/commit/2acef22
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2528
This functionality is already available in 'zfs get'. Providing
it for 'zpool get' is useful and good for consistency.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #2522
Users need to be aware that when replacing devices in an existing
pool they may need to override automatically detected ashift value.
This will all depend on the exact hardware they are using.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2024
Verbatim imports can cause hostid mismatches, but things otherwise work. `zpool
status` does not handle this and will fail when assertions are enabled:
```
zpool: ../../cmd/zpool/zpool_main.c:4418: status_callback: Assertion `reason == ZPOOL_STATUS_OK' failed.
Program received signal SIGABRT, Aborted.
```
Lets instead add a case to display an informative message such as this:
```
pool: rpool
state: ONLINE
status: Mismatch between pool hostid and system hostid on imported pool.
This pool was previously imported into a system with a different hostid,
and then was verbatim imported into this system.
action: Export this pool on all systems on which it is imported.
Then import it to correct the mismatch.
see: http://zfsonlinux.org/msg/ZFS-8000-EY
scan: scrub repaired 0 in 0h8m with 0 errors on Thu Apr 17 19:43:57 2014
config:
NAME STATE READ WRITE CKSUM
rpool ONLINE 0 0 0
sda ONLINE 0 0 0
errors: No known data errors
```
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2342
This functionality has always been missing. But until now there
were no zevents which included an array of strings so it wasn't
missed. However, that's now changed so to ensure this information
is output correctly by 'zpool events -v' the DATA_TYPE_STRING_ARRAY
has been implemented.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Issue #2
zpool_events_next() can be called in blocking mode by specifying a
non-zero value for the "block" parameter. However, the design of
the ZFS Event Daemon (zed) requires additional functionality from
zpool_events_next(). Instead of adding additional arguments to the
function, it makes more sense to use flags that can be bitwise-or'd
together.
This commit replaces the zpool_events_next() int "block" parameter with
an unsigned bitwise "flags" parameter. It also defines ZEVENT_NONE
to specify the default behavior. Since non-blocking mode can be
specified with the existing ZEVENT_NONBLOCK flag, the default behavior
becomes blocking mode. This, in effect, inverts the previous use
of the "block" parameter. Existing callers of zpool_events_next()
have been modified to check for the ZEVENT_NONBLOCK flag.
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2
Due to the very poorly chosen argument name 'cleanup_fd' it was
completely unclear that this file descriptor is used to track the
current cursor location. When the file descriptor is created by
opening ZFS_DEV a private cursor is created in the kernel for the
returned file descriptor. Subsequent calls to zpool_events_next()
and zpool_events_seek() then require the file descriptor as an
argument to reposition the cursor. When the file descriptor is
closed the kernel state tracking the cursor is destroyed.
This patch contains no functional change, it just changes a
few variable names and clarifies the documentation.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Issue #2
Originally, users had to handle spa namespace collisions by either
exporting the already imported pool or by specifying a new name for the
pool with a conflicting name. In the case of root pools from virtual
guests, neither approach to collision resolution is reasonable. This is
addressed by extending the new name syntax with a -t option to specify
that the new name is temporary. When specified, this sets an internal
flag that is passed into the kernel to tell it that all label updates
should refer to the name used in the original label. Consequently, the
original pool name will be retained on export.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2189
ZoL commit 1421c89 unintentionally changed the disk format in a forward-
compatible, but not backward compatible way. This was accomplished by
adding an entry to zbookmark_t, which is included in a couple of
on-disk structures. That lead to the creation of pools with incorrect
dsl_scan_phys_t objects that could only be imported by versions of ZoL
containing that commit. Such pools cannot be imported by other versions
of ZFS or past versions of ZoL.
The additional field has been removed by the previous commit. However,
affected pools must be imported and scrubbed using a version of ZoL with
this commit applied. This will return the pools to a state in which they
may be imported by other implementations.
The 'zpool import' or 'zpool status' command can be used to determine if
a pool is impacted. A message similar to one of the following means your
pool must be scrubbed to restore compatibility.
$ zpool import
pool: zol-0.6.2-173
id: 1165955789558693437
state: ONLINE
status: Errata #1 detected.
action: The pool can be imported using its name or numeric identifier,
however there is a compatibility issue which should be corrected
by running 'zpool scrub'
see: http://zfsonlinux.org/msg/ZFS-8000-ER
config:
...
$ zpool status
pool: zol-0.6.2-173
state: ONLINE
scan: pool compatibility issue detected.
see: https://github.com/zfsonlinux/zfs/issues/2094
action: To correct the issue run 'zpool scrub'.
config:
...
If there was an async destroy in progress 'zpool import' will prevent
the pool from being imported. Further advice on how to proceed will be
provided by the error message as follows.
$ zpool import
pool: zol-0.6.2-173
id: 1165955789558693437
state: ONLINE
status: Errata #2 detected.
action: The pool can not be imported with this version of ZFS due to an
active asynchronous destroy. Revert to an earlier version and
allow the destroy to complete before updating.
see: http://zfsonlinux.org/msg/ZFS-8000-ER
config:
...
Pools affected by the damaged dsl_scan_phys_t can be detected prior to
an upgrade by running the following command as root:
zdb -dddd poolname 1 | grep -P '^\t\tscan = ' | sed -e 's;scan = ;;' | wc -w
Note that `poolname` must be replaced with the name of the pool you wish
to check. A value of 25 indicates the dsl_scan_phys_t has been damaged.
A value of 24 indicates that the dsl_scan_phys_t is normal. A value of 0
indicates that there has never been a scrub run on the pool.
The regression caused by the change to zbookmark_t never made it into a
tagged release, Gentoo backports, Ubuntu, Debian, Fedora, or EPEL
stable respositorys. Only those using the HEAD version directly from
Github after the 0.6.2 but before the 0.6.3 tag are affected.
This patch does have one limitation that should be mentioned. It will not
detect errata #2 on a pool unless errata #1 is also present. It expected
this will not be a significant problem because pools impacted by errata #2
have a high probably of being impacted by errata #1.
End users can ensure they do no hit this unlikely case by waiting for all
asynchronous destroy operations to complete before updating ZoL. The
presence of any background destroys on any imported pools can be checked
by running `zpool get freeing` as root. This will display a non-zero
value for any pool with an active asynchronous destroy.
Lastly, it is expected that no user data has been lost as a result of
this erratum.
Original-patch-by: Tim Chase <tim@chase2k.com>
Reworked-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2094
From time to time it may be necessary to inform the pool administrator
about an errata which impacts their pool. These errata will by shown
to the administrator through the 'zpool status' and 'zpool import'
output as appropriate. The errata must clearly describe the issue
detected, how the pool is impacted, and what action should be taken
to resolve the situation. Additional information for each errata will
be provided at http://zfsonlinux.org/msg/ZFS-8000-ER.
To accomplish the above this patch adds the required infrastructure to
allow the kernel modules to notify the utilities that an errata has
been detected. This is done through the ZPOOL_CONFIG_ERRATA uint64_t
which has been added to the pool configuration nvlist.
To add a new errata the following changes must be made:
* A new errata identifier must be assigned by adding a new enum value
to the zpool_errata_t type. New enums must be added to the end to
preserve the existing ordering.
* Code must be added to detect the issue. This does not strictly
need to be done at pool import time but doing so will make the
errata visible in 'zpool import' as well as 'zpool status'. Once
detected the spa->spa_errata member should be set to the new enum.
* If possible code should be added to clear the spa->spa_errata member
once the errata has been resolved.
* The show_import() and status_callback() functions must be updated
to include an informational message describing the errata. This
should include an action message describing what an administrator
should do to address the errata.
* The documentation at http://zfsonlinux.org/msg/ZFS-8000-ER must be
updated to describe the errata. This space can be used to provide
as much additional information as needed to fully describe the errata.
A link to this documentation will be automatically generated in the
output of 'zpool import' and 'zpool status'.
Original-idea-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Richard Yao <ryao@gentoo.or
Issue #2094
Both the zpool_import_status() and zpool_get_status() functions
return the zpool_status_t enum. This explicit type should be used
rather than the more generic int type.
This patch makes no functional change and should only be considered
code cleanup. It happens to have been done in the context of #2094
because that's when I noticed this issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Richard Yao <ryao@gentoo.or
Issue #2094
The vast majority of these changes are in Linux specific code.
They are the result of not having an automated style checker to
validate the code when it was originally written. Others were
caused when the common code was slightly adjusted for Linux.
This patch contains no functional changes. It only refreshes
the code to conform to style guide.
Everyone submitting patches for inclusion upstream should now
run 'make checkstyle' and resolve any warning prior to opening
a pull request. The automated builders have been updated to
fail a build if when 'make checkstyle' detects an issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1821
3745 zpool create should treat -O mountpoint and -m the same
3811 zpool create -o altroot=/xyz -O mountpoint=/mnt ignores
the mountpoint option
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Christopher Siden <christopher.siden@delphix.com>
References:
https://www.illumos.org/issues/3745https://www.illumos.org/issues/3811illumos/illumos-gate@8b71377531
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
This works the same as the -p switch to "zfs get", displaying full
resolution values for appropriate attributes.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1813
Document the "-D" and "-T" options and the optional interval
and count or "zpool status".
Also for zpool's man page, use a consistent order for the
various "-T" options to match the program's help output.
Document the effect of additional "-D" options for zdb.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1786
2882 implement libzfs_core
2883 changing "canmount" property to "on" should not always remount dataset
2900 "zfs snapshot" should be able to create multiple, arbitrary snapshots at once
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Chris Siden <christopher.siden@delphix.com>
Reviewed by: Garrett D'Amore <garrett@damore.org>
Reviewed by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Dan Kruchinin <dan.kruchinin@gmail.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
https://www.illumos.org/issues/2882https://www.illumos.org/issues/2883https://www.illumos.org/issues/2900illumos/illumos-gate@4445fffbbb
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1293
Porting notes:
WARNING: This patch changes the user/kernel ABI. That means that
the zfs/zpool utilities built from master are NOT compatible with
the 0.6.2 kernel modules. Ensure you load the matching kernel
modules from master after updating the utilities. Otherwise the
zfs/zpool commands will be unable to interact with your pool and
you will see errors similar to the following:
$ zpool list
failed to read pool configuration: bad address
no pools available
$ zfs list
no datasets available
Add zvol minor device creation to the new zfs_snapshot_nvl function.
Remove the logging of the "release" operation in
dsl_dataset_user_release_sync(). The logging caused a null dereference
because ds->ds_dir is zeroed in dsl_dataset_destroy_sync() and the
logging functions try to get the ds name via the dsl_dataset_name()
function. I've got no idea why this particular code would have worked
in Illumos. This code has subsequently been completely reworked in
Illumos commit 3b2aab1 (3464 zfs synctask code needs restructuring).
Squash some "may be used uninitialized" warning/erorrs.
Fix some printf format warnings for %lld and %llu.
Apply a few spa_writeable() changes that were made to Illumos in
illumos/illumos-gate.git@cd1c8b8 as part of the 3112, 3113, 3114 and
3115 fixes.
Add a missing call to fnvlist_free(nvl) in log_internal() that was added
in Illumos to fix issue 3085 but couldn't be ported to ZoL at the time
(zfsonlinux/zfs@9e11c73) because it depended on future work.
Due to an uninitialized variable it was possible for the command
'zpool list -H' to return a non-zero error when there are no pools.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1605
The FreeBSD implementation of zfs adds the 'zpool labelclear'
command. Since this functionality is helpful and straight
forward to add it is being included in ZoL.
References:
freebsd/freebsd@119a041dc9
Ported-by: Dmitry Khasanov <pik4ez@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1126
For "zpool events -f" flush stdout to ensure the last zevent
is always printed immediately.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1568
3306 zdb should be able to issue reads in parallel
3321 'zpool reopen' command should be documented in the man
page and help
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matt Ahrens <matthew.ahrens@delphix.com>
Reviewed by: Christopher Siden <chris.siden@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
illumos/illumos-gate@31d7e8fa33https://www.illumos.org/issues/3306https://www.illumos.org/issues/3321
The vdev_file.c implementation in this patch diverges significantly
from the upstream version. For consistenty with the vdev_disk.c
code the upstream version leverages the Illumos bio interfaces.
This makes sense for Illumos but not for ZoL for two reasons.
1) The vdev_disk.c code in ZoL has been rewritten to use the
Linux block device interfaces which differ significantly
from those in Illumos. Therefore, updating the vdev_file.c
to use the Illumos interfaces doesn't get you consistency
with vdev_disk.c.
2) Using the upstream patch as is would requiring implementing
compatibility code for those Solaris block device interfaces
in user and kernel space. That additional complexity could
lead to confusion and doesn't buy us anything.
For these reasons I've opted to simply move the existing vn_rdwr()
as is in to the taskq function. This has the advantage of being
low risk and easy to understand. Moving the vn_rdwr() function
in to its own taskq thread also neatly avoids the possibility of
a stack overflow.
Finally, because of the additional work which is being handled by
the free taskq the number of threads has been increased. The
thread count under Illumos defaults to 100 but was decreased to 2
in commit 08d08e due to contention. We increase it to 8 until
the contention can be address by porting Illumos #3581.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1354
`zpool status -x` should only flag errors or where the pool is
unavailable. If it imported fine but isn't using the latest features
available in the code, that's not an error.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1319
This is a minor nit, but the second line of the 'action' message
when you need to upgrade your pool to support feature flags exceeds
the standard 80 character limit. Fix it by moving the word
'feature' on to the third line.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
1337 `zpool status -D' should tell if there are no DDT entries
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Approved by: Albert Lee <trisk@nexenta.com>
References:
illumos/illumos-gate@ce72e614c1
illumos changeset: 13432:d1ad8d106d64
https://www.illumos.org/issues/1337
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
2762 zpool command should have better support for feature flags
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
illumos/illumos-gate@57221772c3https://www.illumos.org/issues/2762
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
2619 asynchronous destruction of ZFS file systems
2747 SPA versioning with zfs feature flags
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <gwilson@delphix.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Dan Kruchinin <dan.kruchinin@gmail.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
illumos/illumos-gate@53089ab7c8illumos/illumos-gate@ad135b5d64
illumos changeset: 13700:2889e2596bd6
https://www.illumos.org/issues/2619https://www.illumos.org/issues/2747
NOTE: The grub specific changes were not ported. This change
must be made to the Linux grub packages.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Commit df83110856 missed update to
getopt() call, while delivering all the rest. This commit adds
"o" to getopt().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #566
When adding devices to an existing pool "ashift" property is
auto-detected. However, if this property was overridden at
the pool creation time (i.e. zpool create -o ashift=12 tank ...)
this may not be what the user wants. This commit lets the user
specify the value of "ashift" property to be used with newly
added drives. For example,
zpool add -o ashift=12 tank disk1
zpool attach -o ashift=12 tank disk1 disk2
Signed-off-by: Cyril Plisko <cyril.plisko@mountall.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#566
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Reviewed by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Garrett D'Amore <garrett@damore.org>
Approved by: Richard Lowe <richlowe@richlowe.net>
Refererces to Illumos issue:
https://www.illumos.org/issues/2671
This patch has been slightly modified from the upstream Illumos
version. In the upstream implementation a warning message is
logged to the console. To prevent pointless console noise this
notification is now posted as a "ereport.fs.zfs.vdev.bad_ashift"
event.
The event indicates a non-optimial (but entirely safe) ashift
value was used to create the pool. Depending on your workload
this may impact pool performance. Unfortunately, the only way
to correct the issue is to recreate the pool with a new ashift.
NOTE: The unrelated fix to the comment in zpool_main.c appears
in the upstream commit and was preserved for consistnecy.
Ported-by: Cyril Plisko <cyril.plisko@mountall.com>
Reworked-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#955
The goal of this change is to make 'zpool import' prefer to use
the peristent /dev/mapper or /dev/disk/by-* paths. These are far
preferable to the devices in /dev/ whos names are not persistent
and are determined by the order in which a device is detected.
This patch improves things by changing the default search path from
just to the top level /dev/ directory to (in order):
/dev/disk/by-vdev - Custom rules, use first if they exist
/dev/disk/zpool - Custom rules, use first if they exist
/dev/mapper - Use multipath devices before components
/dev/disk/by-uuid - Single unique entry and persistent
/dev/disk/by-id - May be multiple entries and persistent
/dev/disk/by-path - Encodes physical location and persistent
/dev/disk/by-label - Custom persistent labels
/dev - UNSAFE device names will change
The default search path can be overriden by setting the
ZPOOL_IMPORT_PATH environment variable. This must be a colon
delimited list of paths which are searched for vdevs. If the
'zpool import -d' option is specified only those listed paths
will be searched.
Finally, when multiple paths to the same device are found. If one
of the paths is an exact match for the path used last time to import
the pool it will be used. When there are no exact matches the
prefered path will be determined by the provided search order.
This means you can still import a pool and force specific names by
providing the -d <path> option. And the prefered names will persist
as long as those paths exist on your system.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#965
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/1693
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#678
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Alexander Eremin <alexander.eremin@nexenta.com>
Reviewed by: Alexander Stetsenko <ams@nexenta.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/1748
This commit modifies the user to kernel space ioctl ABI. Extra
care should be taken when updating to ensure both the kernel
modules and utilities are updated. If only the user space
component is updated both the 'zpool events' command and the
'zpool reguid' command will not work until the kernel modules
are updated.
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#665
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Reviewed by: Joshua M. Clulow <josh@sysmgr.org>
Approved by: Richard Lowe <richlowe@richlowe.net>
Reference to Illumos issue:
https://www.illumos.org/issues/1946
Ported by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Dan McDonald <danmcd@nexenta.com>
Reviewed by: Garrett D'Amore <garrett@nexenta.com>
Approved by: Eric Schrock <eric.schrock@delphix.com>
Refererce to Illumos issue:
https://www.illumos.org/issues/952
Ported-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#607
When stdout is detected to be a tty use the number of columns
specified by the terminal. If that fails fall back to a default
80 column width. In the non-tty case allow for 999 column lines.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Caught by lint, this permission change was accidentally introduced
by commit 42cb3819f1. Restore the
correct permissions and while I'm at it add a missing whack-bang
to config/ltmain.sh.
lint: executable-not-elf-or-script: zpool_main.c zfs_main.c
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#620
The 'zfs list' and 'zpool list' commands output the message
'no datasets/pools available' to stdout. This should go to
stderr and only the available datasets/pools should go to
stdout. Returning nothing to stdout is expected behavior
when there is nothing to list.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#581
ZFS contains error messages that point to the defunct www.sun.com
domain, which is currently offline. Change these error messages
to use the zfsonlinux.org mirror instead.
This commit depends on:
zfsonlinux/zfsonlinux.github.com@8e10ead3dc
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The zpool sub-commands like iostat, list, and status should
display consistent message when a given pool is unavailable or
no pool is present. This change unifies the default behavior
as follows:
root@prasad:~# ./zpool list 1 2
no pools available
no pools available
root@prasad:~# ./zpool iostat 1 2
no pools available
no pools available
root@prasad:~# ./zpool status 1 2
no pools available
no pools available
root@prasad:~# ./zpool list tan 1 2
cannot open 'tan': no such pool
root@prasad:~# ./zpool iostat tan 1 2
cannot open 'tan': no such pool
root@prasad:~# ./zpool status tan 1 2
cannot open 'tan': no such pool
Reported-by: Rajshree Thorat <rthorat@stec-inc.com>
Signed-off-by: Prasad Joshi <pjoshi@stec-inc.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#306
