zpool iostat allows you to specify only certain vdevs to display.
Currently, if you run 'zpool iostat -c CMD vdev1 vdev2 ...'
on specific vdevs, it will actually run the command on *all* vdevs,
and just display the results for the vdevs you specify. This patch
corrects the behavior to only run the command on the specified vdevs,
and also enables the zpool_iostat_005_pos.ksh tests.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5443
Enable picky cstyle checks and resolve the new warnings. The vast
majority of the changes needed were to handle minor issues with
whitespace formatting. This patch contains no functional changes.
Non-whitespace changes are as follows:
* 8 times ; to { } in for/while loop
* fix missing ; in cmd/zed/agents/zfs_diagnosis.c
* comment (confim -> confirm)
* change endline , to ; in cmd/zpool/zpool_main.c
* a number of /* BEGIN CSTYLED */ /* END CSTYLED */ blocks
* /* CSTYLED */ markers
* change == 0 to !
* ulong to unsigned long in module/zfs/dsl_scan.c
* rearrangement of module_param lines in module/zfs/metaslab.c
* add { } block around statement after for_each_online_node
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5465
This patch adds a command (-c) option to zpool status and zpool iostat. The
-c option allows you to run an arbitrary command on each vdev and display
the first line of output in zpool status/iostat. The environment vars
VDEV_PATH and VDEV_UPATH are set to the vdev's path and "underlying path"
before running the command. For device mapper, multipath, or partitioned
vdevs, VDEV_UPATH is the actual underlying /dev/sd* disk. This can be useful
if the command you're running requires a /dev/sd* device.
The patch also uses /sys/block/<dev>/slaves/ to lookup the underlying device
instead of using libdevmapper. This not only removes the libdevmapper
requirement at build time, but also allows you to resolve device mapper
devices without being root. This means that UDEV_UPATH get set correctly
when running zpool status/iostat as an unprivileged user.
Example:
$ zpool status -c 'echo I am $VDEV_PATH, $VDEV_UPATH'
NAME STATE READ WRITE CKSUM
mypool ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
mpatha ONLINE 0 0 0 I am /dev/mapper/mpatha, /dev/sdc
sdb ONLINE 0 0 0 I am /dev/sdb1, /dev/sdb
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5368
The vast majority of these changes are in Linux specific code.
They are the result of not having an automated style checker to
validate the code when it was originally written. Others were
caused when the common code was slightly adjusted for Linux.
This patch contains no functional changes. It only refreshes
the code to conform to style guide.
Everyone submitting patches for inclusion upstream should now
run 'make checkstyle' and resolve any warning prior to opening
a pull request. The automated builders have been updated to
fail a build if when 'make checkstyle' detects an issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1821
Some disks with internal sectors larger than 512 bytes (e.g., 4k) can
suffer from bad write performance when ashift is not configured
correctly. This is caused by the disk not reporting its actual sector
size, but a sector size of 512 bytes. The drive may behave this way
for compatibility reasons. For example, the WDC WD20EARS disks are
known to exhibit this behavior.
When creating a zpool, ZFS takes that wrong sector size and sets the
"ashift" property accordingly (to 9: 1<<9=512), whereas it should be
set to 12 for 4k sectors (1<<12=4096).
This patch allows an adminstrator to manual specify the known correct
ashift size at 'zpool create' time. This can significantly improve
performance in certain cases. However, it will have an impact on your
total pool capacity. See the updated ashift property description
in the zpool.8 man page for additional details.
Valid values for the ashift property range from 9 to 17 (512B-128KB).
Additionally, you may set the ashift to 0 if you wish to auto-detect
the sector size based on what the disk reports, this is the default
behavior. The most common ashift values are 9 and 12.
Example:
zpool create -o ashift=12 tank raidz2 sda sdb sdc sdd
Closes#280
Original-patch-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
