When forced to resort to ganging, ZFS currently allocates three child
blocks, each one third of the size of the original. This is true
regardless of whether larger allocations could be made, which would
allow us to have fewer gang leaves. This improves performance when
fragmentation is high enough to require ganging, but not so high that
all the free ranges are only just big enough to hold a third of the
recordsize. This is also useful for improving the behavior of a future
change to allow larger gang headers.
We add the ability for the allocation codepath to allocate a range of
sizes instead of a single fixed size. We then use this to pre-allocate
the DVAs for the gang children. If those allocations fail, we fall back
to the normal write path, which will likely re-gang.
Signed-off-by: Paul Dagnelie <paul.dagnelie@klarasystems.com>
Co-authored-by: Paul Dagnelie <paul.dagnelie@klarasystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Sponsored-by: https://despairlabs.com/sponsor/
Signed-off-by: Rob Norris <robn@despairlabs.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Verify that all empty sectors are zero filled before using them to
calculate parity. Failure to do so can result in incorrect parity
columns being generated and written to disk if the contents of an
empty sector are non-zero. This was possible because the checksum
only protects the data portions of the buffer, not the empty sector
padding.
This issue has been addressed by updating raidz_parity_verify() to
check that all dRAID empty sectors are zero filled. Any sectors
which are non-zero will be fixed, repair IO issued, and a checksum
error logged. They can then be safely used to verify the parity.
This specific type of damage is unlikely to occur since it requires
a disk to have silently returned bad data, for an empty sector, while
performing a scrub. However, if a pool were to have been damaged
in this way, scrubbing the pool with this change applied will repair
both the empty sector and parity columns as long as the data checksum
is valid. Checksum errors will be reported in the `zpool status`
output for any repairs which are made.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12857
Correct an assortment of typos throughout the code base.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#11774
This patch adds a new top-level vdev type called dRAID, which stands
for Distributed parity RAID. This pool configuration allows all dRAID
vdevs to participate when rebuilding to a distributed hot spare device.
This can substantially reduce the total time required to restore full
parity to pool with a failed device.
A dRAID pool can be created using the new top-level `draid` type.
Like `raidz`, the desired redundancy is specified after the type:
`draid[1,2,3]`. No additional information is required to create the
pool and reasonable default values will be chosen based on the number
of child vdevs in the dRAID vdev.
zpool create <pool> draid[1,2,3] <vdevs...>
Unlike raidz, additional optional dRAID configuration values can be
provided as part of the draid type as colon separated values. This
allows administrators to fully specify a layout for either performance
or capacity reasons. The supported options include:
zpool create <pool> \
draid[<parity>][:<data>d][:<children>c][:<spares>s] \
<vdevs...>
- draid[parity] - Parity level (default 1)
- draid[:<data>d] - Data devices per group (default 8)
- draid[:<children>c] - Expected number of child vdevs
- draid[:<spares>s] - Distributed hot spares (default 0)
Abbreviated example `zpool status` output for a 68 disk dRAID pool
with two distributed spares using special allocation classes.
```
pool: tank
state: ONLINE
config:
NAME STATE READ WRITE CKSUM
slag7 ONLINE 0 0 0
draid2:8d:68c:2s-0 ONLINE 0 0 0
L0 ONLINE 0 0 0
L1 ONLINE 0 0 0
...
U25 ONLINE 0 0 0
U26 ONLINE 0 0 0
spare-53 ONLINE 0 0 0
U27 ONLINE 0 0 0
draid2-0-0 ONLINE 0 0 0
U28 ONLINE 0 0 0
U29 ONLINE 0 0 0
...
U42 ONLINE 0 0 0
U43 ONLINE 0 0 0
special
mirror-1 ONLINE 0 0 0
L5 ONLINE 0 0 0
U5 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
L6 ONLINE 0 0 0
U6 ONLINE 0 0 0
spares
draid2-0-0 INUSE currently in use
draid2-0-1 AVAIL
```
When adding test coverage for the new dRAID vdev type the following
options were added to the ztest command. These options are leverages
by zloop.sh to test a wide range of dRAID configurations.
-K draid|raidz|random - kind of RAID to test
-D <value> - dRAID data drives per group
-S <value> - dRAID distributed hot spares
-R <value> - RAID parity (raidz or dRAID)
The zpool_create, zpool_import, redundancy, replacement and fault
test groups have all been updated provide test coverage for the
dRAID feature.
Co-authored-by: Isaac Huang <he.huang@intel.com>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Co-authored-by: Don Brady <don.brady@delphix.com>
Co-authored-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mmaybee@cray.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10102
