In a4b21eadec we added the zap_micro_max_size tuneable to raise the size
at which "micro" (single-block) ZAPs are upgraded to "fat" (multi-block)
ZAPs. Before this, a microZAP was limited to 128KiB, which was the old
largest block size. The side effect of raising the max size past 128KiB
is that it be stored in a large block, requiring the large_blocks
feature.
Unfortunately, this means that a backup stream created without the
--large-block (-L) flag to zfs send would split the microZAP block into
smaller blocks and send those, as is normal behaviour for large blocks.
This would be received correctly, but since microZAPs are limited to the
first block in the object by definition, the entries in the later blocks
would be inaccessible. For directory ZAPs, this gives the appearance of
files being lost.
This commit adds a feature flag, large_microzap, that must be enabled
for microZAPs to grow beyond 128KiB, and which will be activated the
first time that occurs. This feature is later checked when generating
the stream and if active, the send operation will abort unless
--large-block has also been requested.
Changing the limit still requires zap_micro_max_size to be changed. The
state of this flag effectively sets the upper value for this tuneable,
that is, if the feature is disabled, the tuneable will be clamped to
128KiB.
A stream flag is also added to ensure that the receiver also activates
its own feature flag upon receiving the stream. This is not strictly
necessary to _use_ the received microZAP, since it doesn't care how
large its block is, but it is required to send the microZAP object on,
otherwise the original problem occurs again.
Because it's difficult to reliably distinguish a microZAP from a fatZAP
from outside the ZAP code, and because it seems unlikely that most
users are affected (a fairly niche tuneable combined with what should be
an uncommon use of send), and for the sake of expediency, this change
activates the feature the first time a microZAP grows to use a large
block, and is never deactivated after that. This can be improved in the
future.
This commit changes nothing for existing pools that already have large
microZAPs. The feature will not be retroactively applied, but will be
activated the next time a microZAP grows past the limit.
Don't use large_blocks feature for enable/disable tests. The
large_microzap depends on large_blocks, so it gets enabled as a
dependency, breaking the test. Instead use feature "longname", which has
the exact same feature characteristics.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16593
In some environments, just making the .zfs control dir hidden from sight
might not be enough. In particular, the following scenarios might
warrant not allowing access at all:
- old snapshots with wrong permissions/ownership
- old snapshots with exploitable setuid/setgid binaries
- old snapshots with sensitive contents
Introducing a new 'disabled' value that not only hides the control dir,
but prevents access to its contents by returning ENOENT solves all of
the above.
The new property value takes advantage of 'iuv' semantics ("ignore
unknown value") to automatically fall back to the old default value when
a pool is accessed by an older version of ZFS that doesn't yet know
about 'disabled' semantics.
I think that technically the zfs_dirlook change is enough to prevent
access, but preventing lookups and dir entries in an already opened .zfs
handle might also be a good idea to prevent races when modifying the
property at runtime.
Add zfs_snapshot_no_setuid parameter to control whether automatically
mounted snapshots have the setuid mount option set or not.
this could be considered a partial fix for one of the scenarios
mentioned in desired.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Co-authored-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Closes#3963Closes#16587
This patch adds the ability for zfs to support file/dir name up to 1023
bytes. This number is chosen so we can support up to 255 4-byte
characters. This new feature is represented by the new feature flag
feature@longname.
A new dataset property "longname" is also introduced to toggle longname
support for each dataset individually. This property can be disabled,
even if it contains longname files. In such case, new file cannot be
created with longname but existing longname files can still be looked
up.
Note that, to my knowledge native Linux filesystems don't support name
longer than 255 bytes. So there might be programs not able to work with
longname.
Note that NFS server may needs to use exportfs_get_name to reconnect
dentries, and the buffer being passed is limit to NAME_MAX+1 (256). So
NFS may not work when longname is enabled.
Note, FreeBSD vfs layer imposes a limit of 255 name lengh, so even
though we add code to support it here, it won't actually work.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#15921
Reflect f2330bd156
change in our man pages and add some context.
Wording is primarily copy-pasted from code comments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#16581
It's the main recommendation to set xattr=sa
even in man pages, so let's set it by default.
xattr=sa don't use feature flag, so in the worst
case we'll have non-readable xattrs by other
non-openzfs platforms.
Non-overridden default `xattr` prop of existing pools
will automatically use `sa` after this commit too.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#15147
GRUB is not able to detect ZFS pool if snaphsot of top level boot
pool is created. This issue is observed with GRUB versions up to
v2.06 if extensible_dataset feature is enabled on ZFS boot pool.
compatibility=grub2-2.06 would enable all read-only compatible
zpool features except extensible_dataset and other features that
depend on it.
The existing grub2 compatibility file is now renamed to grub2-2.12 to
reflect the appropriate grub2 version. grub2-2.12 lists all read-only
features that can be enabled on boot pool for grub2 with version 2.12
onwards.
A new symlink grub2 is created that currently points to the grub2-2.12
compatibility file.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13873Closes#15261Closes#15909
Now default compression is lz4, which can stop
compression process by itself on incompressible data.
If there are additional size checks -
we will only make our compressratio worse.
New usable compression thresholds are:
- less than BPE_PAYLOAD_SIZE (embedded_data feature);
- at least one saved sector.
Old 12.5% threshold is left to minimize affect
on existing user expectations of CPU utilization.
If data wasn't compressed - it will be saved as
ZIO_COMPRESS_OFF, so if we really need to recompress
data without ashift info and check anything -
we can just compress it with zero threshold.
So, we don't need a new feature flag here!
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#9416
Adding O_DIRECT support to ZFS to bypass the ARC for writes/reads.
O_DIRECT support in ZFS will always ensure there is coherency between
buffered and O_DIRECT IO requests. This ensures that all IO requests,
whether buffered or direct, will see the same file contents at all
times. Just as in other FS's , O_DIRECT does not imply O_SYNC. While
data is written directly to VDEV disks, metadata will not be synced
until the associated TXG is synced.
For both O_DIRECT read and write request the offset and request sizes,
at a minimum, must be PAGE_SIZE aligned. In the event they are not,
then EINVAL is returned unless the direct property is set to always (see
below).
For O_DIRECT writes:
The request also must be block aligned (recordsize) or the write
request will take the normal (buffered) write path. In the event that
request is block aligned and a cached copy of the buffer in the ARC,
then it will be discarded from the ARC forcing all further reads to
retrieve the data from disk.
For O_DIRECT reads:
The only alignment restrictions are PAGE_SIZE alignment. In the event
that the requested data is in buffered (in the ARC) it will just be
copied from the ARC into the user buffer.
For both O_DIRECT writes and reads the O_DIRECT flag will be ignored in
the event that file contents are mmap'ed. In this case, all requests
that are at least PAGE_SIZE aligned will just fall back to the buffered
paths. If the request however is not PAGE_SIZE aligned, EINVAL will
be returned as always regardless if the file's contents are mmap'ed.
Since O_DIRECT writes go through the normal ZIO pipeline, the
following operations are supported just as with normal buffered writes:
Checksum
Compression
Encryption
Erasure Coding
There is one caveat for the data integrity of O_DIRECT writes that is
distinct for each of the OS's supported by ZFS.
FreeBSD - FreeBSD is able to place user pages under write protection so
any data in the user buffers and written directly down to the
VDEV disks is guaranteed to not change. There is no concern
with data integrity and O_DIRECT writes.
Linux - Linux is not able to place anonymous user pages under write
protection. Because of this, if the user decides to manipulate
the page contents while the write operation is occurring, data
integrity can not be guaranteed. However, there is a module
parameter `zfs_vdev_direct_write_verify` that controls the
if a O_DIRECT writes that can occur to a top-level VDEV before
a checksum verify is run before the contents of the I/O buffer
are committed to disk. In the event of a checksum verification
failure the write will return EIO. The number of O_DIRECT write
checksum verification errors can be observed by doing
`zpool status -d`, which will list all verification errors that
have occurred on a top-level VDEV. Along with `zpool status`, a
ZED event will be issues as `dio_verify` when a checksum
verification error occurs.
ZVOLs and dedup is not currently supported with Direct I/O.
A new dataset property `direct` has been added with the following 3
allowable values:
disabled - Accepts O_DIRECT flag, but silently ignores it and treats
the request as a buffered IO request.
standard - Follows the alignment restrictions outlined above for
write/read IO requests when the O_DIRECT flag is used.
always - Treats every write/read IO request as though it passed
O_DIRECT and will do O_DIRECT if the alignment restrictions
are met otherwise will redirect through the ARC. This
property will not allow a request to fail.
There is also a module parameter zfs_dio_enabled that can be used to
force all reads and writes through the ARC. By setting this module
parameter to 0, it mimics as if the direct dataset property is set to
disabled.
Reviewed-by: Brian Behlendorf <behlendorf@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Co-authored-by: Matt Macy <mmacy@FreeBSD.org>
Co-authored-by: Brian Behlendorf <behlendorf@llnl.gov>
Closes#10018
This is the supporting infrastructure for the upcoming dedup features.
Traditionally, dedup objects live directly in the MOS root. While their
details vary (checksum, type and class), they are all the same "kind" of
thing - a store of dedup entries.
The new features are more varied than that, and are better thought of as
a set of related stores for the overall state of a dedup table.
This adds a new feature flag, SPA_FEATURE_FAST_DEDUP. Enabling this will
cause new DDTs to be created as a ZAP in the MOS root, named
DDT-<checksum>. The is used as the root object for the normal type/class
store objects, but will also be a place for any storage required by new
features.
This commit adds two new fields to ddt_t, for version and flags. These
are intended to describe the structure and features of the overall dedup
table, and are stored as-is in the DDT root. In this commit, flags are
always zero, but the intent is that they can be used to hang optional
logic or state onto for new dedup features. Version is always 1.
For a "legacy" dedup table, where no DDT root directory exists, the
version will be 0.
ddt_configure() is expected to determine the version and flags features
currently in operation based on whether or not the fast_dedup feature is
enabled, and from what's available on disk. In this way, its possible to
support both old and new tables.
This also provides a migration path. A legacy setup can be upgraded to
FDT by creating the DDT root ZAP, moving the existing objects into it,
and setting version and flags appropriately. There's no support for that
here, but it would be straightforward to add later and allows the
possibility that newer features could be applied to existing dedup
tables.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: iXsystems, Inc.
Closes#15892
The documentation mentioned that the property name can be 256 characters
long. This was incorrect. The last byte is reserved for NUL, so the
name provided by the operator can be only 255 characters long.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <0mp@FreeBSD.org>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Closes#16248
This change adds a new `zpool prefetch -t ddt $pool` command which
causes a pool's DDT to be loaded into the ARC. The primary goal is to
remove the need to "warm" a pool's cache before deduplication stops
slowing write performance. It may also provide a way to reload portions
of a DDT if they have been flushed due to inactivity.
Sponsored-by: iXsystems, Inc.
Sponsored-by: Catalogics, Inc.
Sponsored-by: Klara, Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Will Andrews <will.andrews@klarasystems.com>
Signed-off-by: Fred Weigel <fred.weigel@klarasystems.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Will Andrews <will.andrews@klarasystems.com>
Co-authored-by: Don Brady <don.brady@klarasystems.com>
Closes#15890
This adds two new pool properties:
- dedup_table_size, the total size of all DDTs on the pool; and
- dedup_table_quota, the maximum possible size of all DDTs in the pool
When set, quota will be enforced by checking when a new entry is about
to be created. If the pool is over its dedup quota, the entry won't be
created, and the corresponding write will be converted to a regular
non-dedup write. Note that existing entries can be updated (ie their
refcounts changed), as that reuses the space rather than requiring more.
dedup_table_quota can be set to 'auto', which will set it based on the
size of the devices backing the "dedup" allocation device. This makes it
possible to limit the DDTs to the size of a dedup vdev only, such that
when the device fills, no new blocks are deduplicated.
Sponsored-by: iXsystems, Inc.
Sponsored-By: Klara Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Rob Wing <rob.wing@klarasystems.com>
Co-authored-by: Sean Eric Fagan <sean.fagan@klarasystems.com>
Closes#15889
There has been a bugzilla PR#147881 requesting this
for a long time (14 years!). It extends the syntax of
the ZFS shanenfs property (for FreeBSD only) to allow
multiple sets of options for different hosts/nets,
separated by ';'s.
Signed-off-by: Rick Macklem <rmacklem@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Sponsored-by: Klara, Inc.
Sponsored-By: Wasabi Technology, Inc.
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Don Brady <don.brady@klarasystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
This commit fixes what is probably a copy-paste mistake. The
`dracut.zfs` manpage claims that the `bootfs.rollback` option executes
`zfs snapshot -Rf`. `zfs snapshot` does not have a `-R` option. `zfs
rollback` does.
Signed-off-by: Alphan Yılmaz <alphanyilmaz@gmail.com>
Reviewed-by: Rob Norris <rob.norris@klarasystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
The ZFS module parameter name is zfs_prefetch_disable, not
zfs_disable_prefetch.
Signed-off-by: Peter Doherty <peterd@acranox.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Slow disk response times can be indicative of a failing drive. ZFS
currently tracks slow I/Os (slower than zio_slow_io_ms) and generates
events (ereport.fs.zfs.delay). However, no action is taken by ZED,
like is done for checksum or I/O errors. This change adds slow disk
diagnosis to ZED which is opt-in using new VDEV properties:
VDEV_PROP_SLOW_IO_N
VDEV_PROP_SLOW_IO_T
If multiple VDEVs in a pool are undergoing slow I/Os, then it skips
the zpool_vdev_degrade().
Sponsored-By: OpenDrives Inc.
Sponsored-By: Klara Inc.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Rob Wing <rob.wing@klarasystems.com>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Closes#15469
When two datasets share the same master encryption key, it is safe
to clone encrypted blocks. Currently only snapshots and clones
of a dataset share with it the same encryption key.
Added a test for:
- Clone from encrypted sibling to encrypted sibling with
non encrypted parent
- Clone from encrypted parent to inherited encrypted child
- Clone from child to sibling with encrypted parent
- Clone from snapshot to the original datasets
- Clone from foreign snapshot to a foreign dataset
- Cloning from non-encrypted to encrypted datasets
- Cloning from encrypted to non-encrypted datasets
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Original-patch-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Signed-off-by: Kay Pedersen <mail@mkwg.de>
Closes#15544
This commit updates zpool-features.7 man page to add newly added
zpool features to grub2 compatibility list.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15505
This feature allows disks to be added one at a time to a RAID-Z group,
expanding its capacity incrementally. This feature is especially useful
for small pools (typically with only one RAID-Z group), where there
isn't sufficient hardware to add capacity by adding a whole new RAID-Z
group (typically doubling the number of disks).
== Initiating expansion ==
A new device (disk) can be attached to an existing RAIDZ vdev, by
running `zpool attach POOL raidzP-N NEW_DEVICE`, e.g. `zpool attach tank
raidz2-0 sda`. The new device will become part of the RAIDZ group. A
"raidz expansion" will be initiated, and the new device will contribute
additional space to the RAIDZ group once the expansion completes.
The `feature@raidz_expansion` on-disk feature flag must be `enabled` to
initiate an expansion, and it remains `active` for the life of the pool.
In other words, pools with expanded RAIDZ vdevs can not be imported by
older releases of the ZFS software.
== During expansion ==
The expansion entails reading all allocated space from existing disks in
the RAIDZ group, and rewriting it to the new disks in the RAIDZ group
(including the newly added device).
The expansion progress can be monitored with `zpool status`.
Data redundancy is maintained during (and after) the expansion. If a
disk fails while the expansion is in progress, the expansion pauses
until the health of the RAIDZ vdev is restored (e.g. by replacing the
failed disk and waiting for reconstruction to complete).
The pool remains accessible during expansion. Following a reboot or
export/import, the expansion resumes where it left off.
== After expansion ==
When the expansion completes, the additional space is available for use,
and is reflected in the `available` zfs property (as seen in `zfs list`,
`df`, etc).
Expansion does not change the number of failures that can be tolerated
without data loss (e.g. a RAIDZ2 is still a RAIDZ2 even after
expansion).
A RAIDZ vdev can be expanded multiple times.
After the expansion completes, old blocks remain with their old
data-to-parity ratio (e.g. 5-wide RAIDZ2, has 3 data to 2 parity), but
distributed among the larger set of disks. New blocks will be written
with the new data-to-parity ratio (e.g. a 5-wide RAIDZ2 which has been
expanded once to 6-wide, has 4 data to 2 parity). However, the RAIDZ
vdev's "assumed parity ratio" does not change, so slightly less space
than is expected may be reported for newly-written blocks, according to
`zfs list`, `df`, `ls -s`, and similar tools.
Sponsored-by: The FreeBSD Foundation
Sponsored-by: iXsystems, Inc.
Sponsored-by: vStack
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Authored-by: Matthew Ahrens <mahrens@delphix.com>
Contributions-by: Fedor Uporov <fuporov.vstack@gmail.com>
Contributions-by: Stuart Maybee <stuart.maybee@comcast.net>
Contributions-by: Thorsten Behrens <tbehrens@outlook.com>
Contributions-by: Fmstrat <nospam@nowsci.com>
Contributions-by: Don Brady <dev.fs.zfs@gmail.com>
Signed-off-by: Don Brady <dev.fs.zfs@gmail.com>
Closes#15022
Currently, zvol threading can be switched through the zvol_request_sync
module parameter system-wide. By making it a zvol property, zvol
threading can be switched per zvol.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#15409
ZFS prefetch is currently governed by the zfs_prefetch_disable
tunable. However, this is a module-wide settings - if a specific
dataset benefits from prefetch, while others have issue with it,
an optimal solution does not exists.
This commit introduce the "prefetch" tri-state property, which enable
granular control (at dataset/volume level) for prefetching.
This patch does not remove the zfs_prefetch_disable, which remains
a system-wide switch for enable/disable prefetch. However, to avoid
duplication, it would be preferable to deprecate and then remove
the module tunable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Gionatan Danti <g.danti@assyoma.it>
Co-authored-by: Gionatan Danti <g.danti@assyoma.it>
Closes#15237Closes#15436
Here I'm trying to succinctly introduce the concept, the basics of its
construction, how its different to dedup, how to use it, and where its
limitations lie, in four paragraphs and with enough searchable terms to
help the reader find more information both within OpenZFS and elsewhere.
Phew.
Sponsored-By: Klara, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#15362
This commit adds '-u' flag for zfs set operation. With this flag,
mountpoint, sharenfs and sharesmb properties can be updated
without actually mounting or sharing the dataset.
Previously, if dataset was unmounted, and mountpoint property was
updated, dataset was not mounted after the update. This behavior
is changed in #15240. We mount the dataset whenever mountpoint
property is updated, regardless if it's mounted or not.
To provide the user with option to keep the dataset unmounted and
still update the mountpoint without mounting the dataset, '-u'
flag can be used.
If any of mountpoint, sharenfs or sharesmb properties are updated
with '-u' flag, the property is set to desired value but the
operation to (re/un)mount and/or (re/un)share the dataset is not
performed and dataset remains as it was before.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15322
Currently redaction bookmarks and their associated redaction lists
have a relatively low limit of 36 redaction snapshots. This is imposed
by the number of snapshot GUIDs that fit in the bonus buffer of the
redaction list object. While this is more than enough for most use
cases, there are some limited cases where larger numbers would be
useful to support.
We tweak the redaction list creation code to use a spill block if
the number of redaction snapshots is above the amount that would fit
in the bonus buffer. We also make a small change to allow spill blocks
to be use for types of data besides SA. In order to fully leverage
this logic, we also change the redaction code to use vmem_alloc, to
handle extremely large allocations if needed. Finally, small tweaks
were made to the zfs commands and the test suite.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#15018
- Distribute zfs-[un]jail.8 on FreeBSD and zfs-[un]zone.8 on Linux
- zfsprops.7: mirror zoned/jailed, only available on respective platforms
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#15161
GRUB2 is compatible with all "read-only compatible" features,
so it is safe to add new features of this type to the grub2
compatibility list. We generally want to include all compatible
features, to minimize the differences between grub2-compatible
pools and no-compatibility pools.
Adding new properties `livelist` and `zpool_checkpoint` accordingly.
Also adding them to the man page which references this file as an
example, for consistency.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#14893
For the head_errlog feature use dsl_dataset_hold_obj_flags() instead of
dsl_dataset_hold_obj() in order to enable access to the encryption keys
(if loaded). This enables reporting of errors in encrypted filesystems
which are not mounted but have their keys loaded.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14837
Usage:
zpool set org.freebsd:comment="this is my pool" poolname
Tests are based on zfs_set's user property tests.
Also stop truncating property values at MAXNAMELEN, use ZFS_MAXPROPLEN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Beckhoff Automation GmbH & Co. KG.
Sponsored-by: Klara Inc.
Closes#11680
And add it to the AVZ, this is not backwards compatible with older pools
due to an assertion in spa_sync() that verifies the number of ZAPs of
all vdevs matches the number of ZAPs in the AVZ.
Granted, the assertion only applies to #DEBUG builds - still, a feature
flag is introduced to avoid the assertion, com.klarasystems:vdev_zaps_v2
Notably, this allows to get/set properties on the root vdev:
% zpool set user:prop=value <pool> root-0
Before this commit, it was already possible to get/set properties on
top-level vdevs with the syntax <type>-<vdev_id> (e.g. mirror-0):
% zpool set user:prop=value <pool> mirror-0
This syntax also applies to the root vdev as it is is of type 'root'
with a vdev_id of 0, root-0. The keyword 'root' as an alias for
'root-0'.
The following tests have been added:
- zpool get all properties from root vdev
- zpool set a property on root vdev
- verify root vdev ZAP is created
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology
Submitted-by: Klara, Inc.
Closes#14405
* Fixed one typo (effects -> affects)
* Re-worded raidz description to make it clearer that it is not
quite the same as RAID5, though similar
* Clarified that data is not necessarily written in a static
stripe width
* Minor grammar consistency improvement
* Noted that "volumes" means zvols
* Fixed a couple of split infinitives
* Clarified that hot spares come from the same pool they were
assigned to
* "we" -> ZFS
* Fixed warnings thrown by mandoc, and removed unnecessary
wordiness in one fixed line.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brandon Thetford <brandon@dodecatec.com>
Closes#14726
This had always worked in my testing, but a user on hardware reported
this to happen 100%, and I reproduced it once with cold VM host caches.
dracut-zfs-generator runs as a systemd generator, i.e. at Some
Relatively Early Time; if root= is a fixed dataset, it tries to
"solve [necessities] statically at generation time".
If by that point zfs-import.target hasn't popped (because the import is
taking a non-negligible amount of time for whatever reason), it'll see
no children for the root datase, and as such generate no mounts.
This has never had any right to work. No-one caught this earlier because
it's just that much more convenient to have root=zfs:AUTO, which orders
itself properly.
To fix this, always run zfs-nonroot-necessities.service;
this additionally simplifies the implementation by:
* making BOOTFS from zfs-env-bootfs.service be the real, canonical,
root dataset name, not just "whatever the first bootfs is",
and only set it if we're ZFS-booting
* zfs-{rollback,snapshot}-bootfs.service can use this instead of
re-implementing it
* having zfs-env-bootfs.service also set BOOTFSFLAGS
* this means the sysroot.mount drop-in can be fixed text
* zfs-nonroot-necessities.service can also be constant and always
enabled, because it's conditioned on BOOTFS being set
There is no longer any code generated at run-time
(the sysroot.mount drop-in is an unavoidable gratuitous cp).
The flow of BOOTFS{,FLAGS} from zfs-env-bootfs.service to sysroot.mount
is not noted explicitly in dracut.zfs(7), because (a) at some point it's
just visual noise and (b) it's already ordered via d-p-m.s from z-i.t.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#14690
Address the following bugs in persistent error log:
1) Check nested clones, eg "fs->snap->clone->snap2->clone2".
2) When deleting files containing error blocks in those clones (from
"clone" the example above), do not break the check chain.
3) When deleting files in the originating fs before syncing the errlog
to disk, do not break the check chain. This happens because at the
time of introducing the error block in the error list, we do not have
its birth txg and the head filesystem. If the original file is
deleted before the error list is synced to the error log (which is
when we actually lookup the birth txg and the head filesystem), then
we do not have access to this info anymore and break the check chain.
The most prominent change is related to achieving (3). We expand the
spa_error_entry_t structure to accommodate the newly introduced
zbookmark_err_phys_t structure (containing the birth txg of the error
block).Due to compatibility reasons we cannot remove the
zbookmark_phys_t structure and we also need to place the new structure
after se_avl, so it is not accounted for in avl_find(). Then we modify
spa_log_error() to also provide the birth txg of the error block. With
these changes in place we simplify the previously introduced function
get_head_and_birth_txg() (now named get_head_ds()).
We chose not to follow the same approach for the head filesystem (thus
completely removing get_head_ds()) to avoid introducing new lock
contentions.
The stack sizes of nested functions (as measured by checkstack.pl in the
linux kernel) are:
check_filesystem [zfs]: 272 (was 912)
check_clones [zfs]: 64
We also introduced two new tests covering the above changes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14633
Block Cloning allows to manually clone a file (or a subset of its
blocks) into another (or the same) file by just creating additional
references to the data blocks without copying the data itself.
Those references are kept in the Block Reference Tables (BRTs).
The whole design of block cloning is documented in module/zfs/brt.c.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13392
Introduce four new vdev properties:
checksum_n
checksum_t
io_n
io_t
These properties can be used for configuring the thresholds of zed's
diagnosis engine and are interpeted as <N> events in T <seconds>.
When this property is set to a non-default value on a top-level vdev,
those thresholds will also apply to its leaf vdevs. This behavior can be
overridden by explicitly setting the property on the leaf vdev.
Note that, these properties do not persist across vdev replacement. For
this reason, it is advisable to set the property on the top-level vdev
instead of the leaf vdev.
The default values for zed's diagnosis engine (10 events, 600 seconds)
remains unchanged.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Closes#13805
Correct new mandoc errors.
```
STYLE: input text line longer than 80 bytes
STYLE: no blank before trailing delimiter
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#14148
Linux defaults to setting "failfast" on BIOs, so that the OS will not
retry IOs that fail, and instead report the error to ZFS.
In some cases, such as errors reported by the HBA driver, not
the device itself, we would wish to retry rather than generating
vdev errors in ZFS. This new property allows that.
This introduces a per vdev option to disable the failfast option.
This also introduces a global module parameter to define the failfast
mask value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Submitted-by: Klara, Inc.
Closes#14056
Currently, additional/extra copies are created for metadata in
addition to the redundancy provided by the pool(mirror/raidz/draid),
due to this 2 times more space is utilized per inode and this decreases
the total number of inodes that can be created in the filesystem. By
setting redundant_metadata to none, no additional copies of metadata
are created, hence can reduce the space consumed by the additional
metadata copies and increase the total number of inodes that can be
created in the filesystem. Additionally, this can improve file create
performance due to the reduced amount of metadata which needs
to be written.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#13680
Currently, snapshots_changed property is stored in dd_props_zapobj, due
to which the property is assumed to be local. This causes a difference
in behavior with respect to other readonly properties.
This commit stores the snapshots_changed property in dd_object. Source
is not set to local in this case, which makes it consistent with other
readonly properties.
This commit also updates the date string format to include seconds.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13785
When scrubbing an encrypted filesystem with unloaded key still report an
error in zpool status.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@axcient.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13675Closes#13717
Linux sets relatime on mount by default for any file system,
but relatime=off in ZFS disables it explicitly.
Let's be consistent with other file systems on Linux.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#13614
Make dd_snap_cmtime property persistent across mount and unmount
operations by storing in ZAP and restore the value from ZAP on hold
into dd_snap_cmtime instead of updating it.
Expose dd_snap_cmtime as 'snapshots_changed' property that provides a
mechanism to quickly determine whether snapshot list for dataset has
changed without having to mount a dataset or iterate the snapshot list.
It specifies the time at which a snapshot for a dataset was last
created or deleted. This allows us to be more efficient how often we
query snapshots.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13635
Use Dq,Pq/Po/Pc macros. illumos dumpadm is now in section 8.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#13586
This allows ZFS datasets to be delegated to a user/mount namespace
Within that namespace, only the delegated datasets are visible
Works very similarly to Zones/Jailes on other ZFS OSes
As a user:
```
$ unshare -Um
$ zfs list
no datasets available
$ echo $$
1234
```
As root:
```
# zfs list
NAME ZONED MOUNTPOINT
containers off /containers
containers/host off /containers/host
containers/host/child off /containers/host/child
containers/host/child/gchild off /containers/host/child/gchild
containers/unpriv on /unpriv
containers/unpriv/child on /unpriv/child
containers/unpriv/child/gchild on /unpriv/child/gchild
# zfs zone /proc/1234/ns/user containers/unpriv
```
Back to the user namespace:
```
$ zfs list
NAME USED AVAIL REFER MOUNTPOINT
containers 129M 47.8G 24K /containers
containers/unpriv 128M 47.8G 24K /unpriv
containers/unpriv/child 128M 47.8G 128M /unpriv/child
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will.andrews@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Buddy <https://buddy.works>
Closes#12263
