Commit torvalds/linux@9e8925b6 allowed for kernels to be built
without support for mandatory locking (MS_MANDLOCK). This will
result in 'zfs mount' failing when the nbmand=on property is set
if the kernel is built without CONFIG_MANDATORY_FILE_LOCKING.
Unfortunately we can not reliably detect prior to the mount(2) system
call if the kernel was built with this support. The best we can do
is check if the mount failed with EPERM and if we passed 'mand'
as a mount option and then print a more useful error message. e.g.
filesystem 'tank/fs' has the 'nbmand=on' property set, this mount
option may be disabled in your kernel. Use 'zfs set nbmand=off'
to disable this option and try to mount the filesystem again.
Additionally, switch the default error message case to use
strerror() to produce a more human readable message.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4729Closes#6199
Enable picky cstyle checks and resolve the new warnings. The vast
majority of the changes needed were to handle minor issues with
whitespace formatting. This patch contains no functional changes.
Non-whitespace changes are as follows:
* 8 times ; to { } in for/while loop
* fix missing ; in cmd/zed/agents/zfs_diagnosis.c
* comment (confim -> confirm)
* change endline , to ; in cmd/zpool/zpool_main.c
* a number of /* BEGIN CSTYLED */ /* END CSTYLED */ blocks
* /* CSTYLED */ markers
* change == 0 to !
* ulong to unsigned long in module/zfs/dsl_scan.c
* rearrangement of module_param lines in module/zfs/metaslab.c
* add { } block around statement after for_each_online_node
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5465
Fix misleading error message:
"The /dev/zfs device is missing and must be created.", if /etc/mtab is missing.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Eric Desrochers <eric.desrochers@canonical.com>
Closes#4680Closes#5029
Also enable lazytime in mount.zfs
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4482
mount.zfs is called by convention (and util-linux) with arguments
last, i.e.
% mount.zfs <dataset> <mountpoint> -o <options>
This is not a problem on glibc since GNU getopt(3) will reorder the
arguments. However, alternative libc such as musl libc (or glibc with
$POSIXLY_CORRECT set) will not permute argv and fail to parse the -o
<options>. Use getopt_long so musl will permute arguments.
Signed-off-by: Christian Neukirchen <chneukirchen@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4222
Add the required kernel side infrastructure to parse arbitrary
mount options. This enables us to support temporary mount
options in largely the same way it is handled on other platforms.
See the 'Temporary Mount Point Properties' section of zfs(8)
for complete details.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#985Closes#3351
Build products from an out of tree build should be written
relative to the build directory. Sources should be referred
to by their locations in the source directory.
This is accomplished by adding the 'src' and 'obj' variables
for the module Makefile.am, using relative paths to reference
source files, and by setting VPATH when source files are not
co-located with the Makefile. This enables the following:
$ mkdir build
$ cd build
$ ../configure \
--with-spl=$HOME/src/git/spl/ \
--with-spl-obj=$HOME/src/git/spl/build
$ make -s
This change also has the advantage of resolving the following
warning which is generated by modern versions of automake.
Makefile.am:00: warning: source file 'xxx' is in a subdirectory,
Makefile.am:00: but option 'subdir-objects' is disabled
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1082
All fprintf() error messages are moved out of the libzfs_init()
library function where they never belonged in the first place. A
libzfs_error_init() function is added to provide useful error
messages for the most common causes of failure.
Additionally, in libzfs_run_process() the 'rc' variable was renamed
to 'error' for consistency with the rest of the code base.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
When using 'zpool import' to scan for available pools prefer vdev names
which reference vdevs with more valid labels. There should be two labels
at the start of the device and two labels at the end of the device. If
labels are missing then the device has been damaged or is in some other
way incomplete. Preferring names with fully intact labels helps weed out
bad paths and improves the likelihood of being able to import the pool.
This behavior only applies when scanning /dev/ for valid pools. If a
cache file exists the pools described by the cache file will be used.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Closes#3145Closes#2844Closes#3107
Installing outside of the prefix is not permissible under Gentoo Prefix.
The package manager will cause the installation process to fail if/when
it sees this. I could script a workaround inside the ebuild, but it
seemed to make more sense to make this more configurable.
Signed-off-by: Richard Yao <richard.yao@clusterhq.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2641
Change mount code to diagnose filesystem versions that
are not supported by the current implementation.
Change upgrade code to do likewise and refuse to upgrade
a pool if any filesystems on it are a version which is
not supported by the current implementation.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Dan Swartzendruber <dswartz@druber.com>
Closes: #2616
Four new dataset properties have been added to support SELinux. They
are 'context', 'fscontext', 'defcontext' and 'rootcontext' which map
directly to the context options described in mount(8). When one of
these properties is set to something other than 'none'. That string
will be passed verbatim as a mount option for the given context when
the filesystem is mounted.
For example, if you wanted the rootcontext for a filesystem to be set
to 'system_u:object_r:fs_t' you would set the property as follows:
$ zfs set rootcontext="system_u:object_r:fs_t" storage-pool/media
This will ensure the filesystem is automatically mounted with that
rootcontext. It is equivalent to manually specifying the rootcontext
with the -o option like this:
$ zfs mount -o rootcontext=system_u:object_r:fs_t storage-pool/media
By default all four contexts are set to 'none'. Further information
on SELinux contexts is detailed in mount(8) and selinux(8) man pages.
Signed-off-by: Matthew Thode <prometheanfire@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#1504
The vast majority of these changes are in Linux specific code.
They are the result of not having an automated style checker to
validate the code when it was originally written. Others were
caused when the common code was slightly adjusted for Linux.
This patch contains no functional changes. It only refreshes
the code to conform to style guide.
Everyone submitting patches for inclusion upstream should now
run 'make checkstyle' and resolve any warning prior to opening
a pull request. The automated builders have been updated to
fail a build if when 'make checkstyle' detects an issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1821
Add acl, noacl and posixacl to option_map, avoiding ENOENT error
case when mount from util-linux-2.24 execs mount.zfs with any of
those flags
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: renelson <bnelson@nelsonbe.com>
Issue #1968
A minor grammar error was corrected in in the parse_options()
error handling for the ENOENT case.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: renelson <bnelson@nelsonbe.com>
Issue #1968
On some platforms symbols provided by libzfs_core and used by
libzfs were not available to the linker. To avoid this issue
libzfs_core has been added to the list of required libraries
when building utilities which depend on libzfs. This should
have been handled properly by libtool and it's still not
entirely clear why it wasn't on all platforms.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1841
In the current snapshot automount implementation, it is possible for
multiple mounts to attempted concurrently. Only one of the mounts will
succeed and the other will fail. The failed mounts will cause an EREMOTE
to be propagated back to the application.
This commit works around the problem by adding a new exit status,
MOUNT_BUSY to the mount.zfs program which is used when the underlying
mount(2) call returns EBUSY. The zfs code detects this condition and
treats it as if the mount had succeeded.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1819
Libraries that depend on other libraries should list them in ELF's
DT_NEEDED field so that programs linking to them do not need to specify
those libraries unless they depend on them as well. This is not the case
in the current code and the consequence is that anything that needs a
library must know its dependencies. This is fragile and caused GRUB2's
configure script to break when a dependency was added on libblkid in
libzfs.
This resolves that problem by using LIBADD/LDADD to specify libraries in
Makefile.am instead of LDFLAGS. This ensures that proper DT_NEEDED
entries are generated and prevents GRUB2's configure script from
breaking in the presence of a libblkid dependency. This also removes
unneeded dependencies from various files.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1751
A mount failure was accidentally introduced by commit 0c1171d
which reworked the parse_dataset() function to read pool names
from devices. The error case where a label is read from the
device but the pool name/value pair doesn't exist was not
handled properly. In this case we should fall back to the
previous behavior.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1560
To simplify integration with the xfstests test suite the
mount.zfs helper has been extended. When passed a block
device (/dev/sdX) to mount, instead of a pool/dataset,
the pool name will be read from any existing zfs label
and used. This allows you to mount the root dataset of
a zfs filesystem by specifing any of the member vdevs.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
When calling mount(), care must be taken to avoid passing in flags
that are used only by the user space utilities. Otherwise we may
stomp on flags that are reserved for other purposes in the kernel.
In particular, openSUSE 12.3 kernels have added a new MS_RICHACL
super-block flag whose value conflicts with our MS_COMMENT flag. This
causes incorrect behavior such as the umask being ignored. The
MS_COMMENT flag essentially serves as a placeholder in the option_map
data structure of zfs_mount.c, but its value is never used. Therefore
we can avoid the conflict by defining it to 0.
The MS_USERS, MS_OWNER, and MS_GROUP flags also conflict with reserved
flags in the kernel. While this is not known to have caused any
problems, it is nevertheless incorrect. For the purposes of the
mount.zfs helper, the "users", "owner", and "group" options just serve
as hints to set additional implied options. Therefore we now define
their associated mount flags in terms of the options that they imply
rather than giving them unique values.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1457
Rather than just reporting the failure include the passed
mount point and error number.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1153
mountall in Debian depends on being able to pass the -f parameter to
mount, which specifies a fake mount and just updates the mtab. Currently
mount.zfs will fail such a request if it is not passed with -o zfsutil.
This patch allows a fake mount on a non-legacy filesystem to succeed in
the same manner as a -o remount does, thus enabling mountall to work
correctly.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1167
Canonicalize the mount point passed to the mount.zfs helper.
This way a clean path is always added to mtab which ensures
the umount can properly locate and remove the entry.
Test case:
$ mkdir /mnt/foo
$ mount -t zfs zpool/foo /mnt/../mnt/foo////
$ umount /mnt/foo
$ cat /etc/mtab | grep zpool/foo
zpool/foo /mnt/../mnt/foo//// zfs rw 0 0
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#573
Commit e6f290535c added libzpool to
the mount_zfs dependencies. This brought in the nvpair symbols
which are used by libzpool. To resolve this include the libnvpair
library for mount_zfs even though mount_zfs doesn't directly
require any of these symbols.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#926
mount_zfs depends on libzpool for zfs_prop_written since
330d06f90d. Unfortunately, the Makefile
for mount_zfs has not been modified to reflect this. As a result,
libtool doesn't know about the dependency, which may result in the wrong
libzpool being used during the build (e.g. the libzpool from the system
instead of the libzpool from the build directory).
This patch adds the dependency to fix the issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Fixes#909.
Remove all of the generated autotools products from the repository
and update the .gitignore files accordingly.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#718
Currently, zvols have a discard granularity set to 0, which suggests to
the upper layer that discard requests of arbirarily small size and
alignment can be made efficiently.
In practice however, ZFS does not handle unaligned discard requests
efficiently: indeed, it is unable to free a part of a block. It will
write zeros to the specified range instead, which is both useless and
inefficient (see dnode_free_range).
With this patch, zvol block devices expose volblocksize as their discard
granularity, so the upper layer is aware that it's not supposed to send
discard requests smaller than volblocksize.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#862
This is done for compatibility with existing Linux infrastructure.
In particular, when using zfs as a root filesystem there are init
scripts which as part of shutdown remount root read-only. Also,
the new systemd infrastructure being used by Fedora expects to be
able to remount a file system read-write.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #847
The end_writeback() function was changed by moving the call to
inode_sync_wait() earlier in to evict(). This effecitvely changes
the ordering of the sync but it does not impact the details of
the zfs implementation.
However, as part of this change end_writeback() was renamed to
clear_inode() to reflect the new semantics. This change does
impact us and clear_inode() now maps to end_writeback() for
kernels prior to 3.5.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#784
The vmtruncate_range() support has been removed from the kernel in
favor of using the fallocate method in the file_operations table.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #784
The export_operations member ->encode_fh() has been updated to
take both the child and parent inodes. This interface used to
take the child dentry and a bool describing if the parent is needed.
NOTE: While updating this code I noticed that we do not currently
cleanly handle the case where we're passed a connectable parent.
This code should be audited to make sure we're doing the right thing.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #784
Currently, zpool online -e (dynamic vdev expansion) doesn't work on
whole disks because we're invoking ioctl(BLKRRPART) from userspace
while ZFS still has a partition open on the disk, which results in
EBUSY.
This patch moves the BLKRRPART invocation from the zpool utility to the
module. Specifically, this is done just before opening the device in
vdev_disk_open() which is called inside vdev_reopen(). This requires
jumping through some hoops to get to the disk device from the partition
device, and to make sure we can still open the partition after the
BLKRRPART call.
Note that this new code path is triggered on dynamic vdev expansion
only; other actions, like creating a new pool, are unchanged and still
call BLKRRPART from userspace.
This change also depends on API changes which are available in 2.6.37
and latter kernels. The build system has been updated to detect this,
but there is no compatibility mode for older kernels. This means that
online expansion will NOT be available in older kernels. However, it
will still be possible to expand the vdev offline.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#808
When compiling ZFS with CFLAGS=-O0 it will trigger the following error.
Resolve the issue by properly including locale.h.
../../cmd/mount_zfs/mount_zfs.c: In function 'main':
../../cmd/mount_zfs/mount_zfs.c:318:2: warning: implicit declaration
of function 'setlocale' [-Wimplicit-function-declaration]
../../cmd/mount_zfs/mount_zfs.c:318:19: error: 'LC_ALL' undeclared
(first use in this function)
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#724
torvalds/linux@adc0e91ab1 introduced
introduced d_make_root() as a replacement for d_alloc_root(). Further
commits appear to have removed d_alloc_root() from the Linux source
tree. This causes the following failure:
error: implicit declaration of function 'd_alloc_root'
[-Werror=implicit-function-declaration]
To correct this we update the code to use the current d_make_root()
interface for readability. Then we introduce an autotools check
to determine if d_make_root() is available. If it isn't then we
define some compatibility logic which used the older d_alloc_root()
interface.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#776
The mode argument of iops->create()/mkdir()/mknod() was changed from
an 'int' to a 'umode_t'. To prevent a compiler warning an autoconf
check was added to detect the API change and then correctly set a
zpl_umode_t typedef. There is no functional change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#701
A cryptic error code is printed when mounting a legacy dataset to a
non-existent mountpoint. This patch changes this behavior to print
"mount point '%s' does not exist", which is similar to the error
message printed when mounting procfs.
The single quotes were added to be consistent with the existing EBUSY
error message, which is the only difference between this error message
and the one that is printed when the same condition occurs when mounting
procfs.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#633
Allow rigorous (and expensive) tx validation to be enabled/disabled
indepentantly from the standard zfs debugging. When enabled these
checks ensure that all txs are constructed properly and that a dbuf
is never dirtied without taking the correct tx hold.
This checking is particularly helpful when adding new dmu consumers
like Lustre. However, for established consumers such as the zpl
with no known outstanding tx construction problems this is just
overhead.
--enable-debug-dmu-tx - Enable/disable validation of each tx as
--disable-debug-dmu-tx it is constructed. By default validation
is disabled due to performance concerns.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add support for the .zfs control directory. This was accomplished
by leveraging as much of the existing ZFS infrastructure as posible
and updating it for Linux as required. The bulk of the core
functionality is now all there with the following limitations.
*) The .zfs/snapshot directory automount support requires a 2.6.37
or newer kernel. The exception is RHEL6.2 which has backported
the d_automount patches.
*) Creating/destroying/renaming snapshots with mkdir/rmdir/mv
in the .zfs/snapshot directory works as expected. However,
this functionality is only available to root until zfs
delegations are finished.
* mkdir - create a snapshot
* rmdir - destroy a snapshot
* mv - rename a snapshot
The following issues are known defeciences, but we expect them to
be addressed by future commits.
*) Add automount support for kernels older the 2.6.37. This should
be possible using follow_link() which is what Linux did before.
*) Accessing the .zfs/snapshot directory via NFS is not yet possible.
The majority of the ground work for this is complete. However,
finishing this work will require resolving some lingering
integration issues with the Linux NFS kernel server.
*) The .zfs/shares directory exists but no futher smb functionality
has yet been implemented.
Contributions-by: Rohan Puri <rohan.puri15@gmail.com>
Contributiobs-by: Andrew Barnes <barnes333@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#173
Allow a source rpm to be rebuilt with debugging enabled. This
avoids the need to have to manually modify the spec file. By
default debugging is still largely disabled. To enable specific
debugging features use the following options with rpmbuild.
'--with debug' - Enables ASSERTs
# For example:
$ rpmbuild --rebuild --with debug zfs-modules-0.6.0-rc6.src.rpm
Additionally, ZFS_CONFIG has been added to zfs_config.h for
packages which build against these headers. This is critical
to ensure both zfs and the dependant package are using the same
prototype and structure definitions.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
DISCARD (REQ_DISCARD, BLKDISCARD) is useful for thin provisioning.
It allows ZVOL clients to discard (unmap, trim) block ranges from
a ZVOL, thus optimizing disk space usage by allowing a ZVOL to
shrink instead of just grow.
We can't use zfs_space() or zfs_freesp() here, since these functions
only work on regular files, not volumes. Fortunately we can use the
low-level function dmu_free_long_range() which does exactly what we
want.
Currently the discard operation is not added to the log. That's not
a big deal since losing discard requests cannot result in data
corruption. It would however result in disk space usage higher than
it should be. Thus adding log support to zvol_discard() is probably
a good idea for a future improvement.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Currently only the (FALLOC_FL_PUNCH_HOLE) flag combination is
supported, since it's the only one that matches the behavior of
zfs_space(). This makes it pretty much useless in its current
form, but it's a start.
To support other flag combinations we would need to modify
zfs_space() to make it more flexible, or emulate the desired
functionality in zpl_fallocate().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #334
The Linux block device queue subsystem exposes a number of configurable
settings described in Linux block/blk-settings.c. The defaults for these
settings are tuned for hard drives, and are not optimized for ZVOLs. Proper
configuration of these options would allow upper layers (I/O scheduler) to
take better decisions about write merging and ordering.
Detailed rationale:
- max_hw_sectors is set to unlimited (UINT_MAX). zvol_write() is able to
handle writes of any size, so there's no reason to impose a limit. Let the
upper layer decide.
- max_segments and max_segment_size are set to unlimited. zvol_write() will
copy the requests' contents into a dbuf anyway, so the number and size of
the segments are irrelevant. Let the upper layer decide.
- physical_block_size and io_opt are set to the ZVOL's block size. This
has the potential to somewhat alleviate issue #361 for ZVOLs, by warning
the upper layers that writes smaller than the volume's block size will be
slow.
- The NONROT flag is set to indicate this isn't a rotational device.
Although the backing zpool might be composed of rotational devices, the
resulting ZVOL often doesn't exhibit the same behavior due to the COW
mechanisms used by ZFS. Setting this flag will prevent upper layers from
making useless decisions (such as reordering writes) based on incorrect
assumptions about the behavior of the ZVOL.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
zvol_write() assumes that the write request must be written to stable storage
if rq_is_sync() is true. Unfortunately, this assumption is incorrect. Indeed,
"sync" does *not* mean what we think it means in the context of the Linux
block layer. This is well explained in linux/fs.h:
WRITE: A normal async write. Device will be plugged.
WRITE_SYNC: Synchronous write. Identical to WRITE, but passes down
the hint that someone will be waiting on this IO
shortly.
WRITE_FLUSH: Like WRITE_SYNC but with preceding cache flush.
WRITE_FUA: Like WRITE_SYNC but data is guaranteed to be on
non-volatile media on completion.
In other words, SYNC does not *mean* that the write must be on stable storage
on completion. It just means that someone is waiting on us to complete the
write request. Thus triggering a ZIL commit for each SYNC write request on a
ZVOL is unnecessary and harmful for performance. To make matters worse, ZVOL
users have no way to express that they actually want data to be written to
stable storage, which means the ZIL is broken for ZVOLs.
The request for stable storage is expressed by the FUA flag, so we must
commit the ZIL after the write if the FUA flag is set. In addition, we must
commit the ZIL before the write if the FLUSH flag is set.
Also, we must inform the block layer that we actually support FLUSH and FUA.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The second argument of sops->show_options() was changed from a
'struct vfsmount *' to a 'struct dentry *'. Add an autoconf check
to detect the API change and then conditionally define the expected
interface. In either case we are only interested in the zfs_sb_t.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#549
These libraries, which are an artifact of the ZoL development
process, conflict with packages that are already in distribution:
* libspl: SPL Programming Language
* libavl: AVL for Linux
* libefi: GRUB
And these libraries are potential conflicts:
* libshare: the Linux Mount Manager
* libunicode: Perl and Python
Recompose these five ZoL components into the four libraries that are
conventionally provided by Solaris and FreeBSD systems:
+ libnvpair
+ libuutil
+ libzpool
+ libzfs
This change resolves the name conflict, makes ZoL more compatible
with existing software that uses autotools to detect ZFS, and allows
pkg-zfs to better reflect the official Debian kFreeBSD packaging.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #430
The Linux 3.1 kernel has introduced the concept of per-filesystem
shrinkers which are directly assoicated with a super block. Prior
to this change there was one shared global shrinker.
The zfs code relied on being able to call the global shrinker when
the arc_meta_limit was exceeded. This would cause the VFS to drop
references on a fraction of the dentries in the dcache. The ARC
could then safely reclaim the memory used by these entries and
honor the arc_meta_limit. Unfortunately, when per-filesystem
shrinkers were added the old interfaces were made unavailable.
This change adds support to use the new per-filesystem shrinker
interface so we can continue to honor the arc_meta_limit. The
major benefit of the new interface is that we can now target
only the zfs filesystem for dentry and inode pruning. Thus we
can minimize any impact on the caching of other filesystems.
In the context of making this change several other important
issues related to managing the ARC were addressed, they include:
* The dnlc_reduce_cache() function which was called by the ARC
to drop dentries for the Posix layer was replaced with a generic
zfs_prune_t callback. The ZPL layer now registers a callback to
drop these dentries removing a layering violation which dates
back to the Solaris code. This callback can also be used by
other ARC consumers such as Lustre.
arc_add_prune_callback()
arc_remove_prune_callback()
* The arc_reduce_dnlc_percent module option has been changed to
arc_meta_prune for clarity. The dnlc functions are specific to
Solaris's VFS and have already been largely eliminated already.
The replacement tunable now represents the number of bytes the
prune callback will request when invoked.
* Less aggressively invoke the prune callback. We used to call
this whenever we exceeded the arc_meta_limit however that's not
strictly correct since it results in over zeleous reclaim of
dentries and inodes. It is now only called once the arc_meta_limit
is exceeded and every effort has been made to evict other data from
the ARC cache.
* More promptly manage exceeding the arc_meta_limit. When reading
meta data in to the cache if a buffer was unable to be recycled
notify the arc_reclaim thread to invoke the required prune.
* Added arcstat_prune kstat which is incremented when the ARC
is forced to request that a consumer prune its cache. Remember
this will only occur when the ARC has no other choice. If it
can evict buffers safely without invoking the prune callback
it will.
* This change is also expected to resolve the unexpect collapses
of the ARC cache. This would occur because when exceeded just the
arc_meta_limit reclaim presure would be excerted on the arc_c
value via arc_shrink(). This effectively shrunk the entire cache
when really we just needed to reclaim meta data.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#466Closes#292
Regenerating the autotools configuration on Debian and Ubuntu systems
causes compilation to fail with this error message:
cmd/mount_zfs/../../cmd/mount_zfs/mount_zfs.c:403:
undefined reference to `is_selinux_enabled'
In the automake template, set "mount_zfs_LDFLAGS = ... $(LIBSELINUX)"
so that the /sbin/mount.zfs utility is linked to libselinux.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Directly changing inode->i_nlink is deprecated in Linux 3.2 by commit
SHA: bfe8684869601dacfcb2cd69ef8cfd9045f62170
Use the new set_nlink() kernel function instead.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #462
