Traditionally, unused dentries would be cached in the dentry cache until
the associated entry is no longer on disk. The cached dentry continues
to hold an inode reference, causing the inode to be pinned (see previous
commit).
Here we implement the dentry op d_delete, which is roughly analogous to
the drop_inode superblock op, and add a zfs_delete_dentry tunable to
control its behaviour. By default it continues the traditional
behaviour, but when the tunable is enabled, we signal that an unused
dentry should be freed immediately, releasing its inode reference, and
so allowing that inode to be deleted if no longer in use.
Sponsored-by: Klara, Inc.
Sponsored-by: Fastmail Pty Ltd
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <alexander.motin@TrueNAS.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#17746
Traditionally, unused inodes would be held on the superblock inode cache
until the associated on-disk file is removed or the kernel requests
reclaim. On filesystems with millions of rarely-used files, this can be
a lot of unusable memory.
Here we implement the superblock drop_inode method, and add a
zfs_delete_inode tunable to control its behaviour. By default it
continues the traditional behaviour, but when the tunable is enabled, we
signal that the inode should be deleted immediately when the last
reference is dropped, rather than cached. This releases the associated
data to the dbuf cache and ARC, allowing them to be reclaimed normally.
Sponsored-by: Klara, Inc.
Sponsored-by: Fastmail Pty Ltd
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <alexander.motin@TrueNAS.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#17746
Compilation time bug introduced by 87df5e4 commit.
Fix for the compilation error(Linux kernel 6.18.0):
"zfs/module/os/linux/zfs/abd_os.c:920:32: error: implicit declaration
of function ‘nth_page’; did you mean ‘pte_page’?
[-Werror=implicit-function-declaration]".
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rob Norris <robn@despairlabs.com>
Signed-off-by: agiUnderground <alex.dev.cv@gmail.com>
Closes#18034
- mmp_concurrent_import: added test case to verify that concurrent
import correctness. The pool may only be imported once.
- mmp_exported_import: an activity check is now required for pools
which were cleanly exported if the system and pool hostids don't
match.
- mmp_inactive_import: an activity check is now required for any
pool which wasn't cleanly exported, even if the system and pool
hostids match.
- mmp_on_uberblocks: updated expected uberblocks to take in to account
the value MMP_INTERVAL_DEFAULT is set too.
- mmp_reset_interval: reduce the number of iterations from 10 to 3.
This is sufficient to verify functionality and significantly speeds
up the test.
- mmp_on_uberblocks: adjust the thresholds and increase the runtime
to avoid false positives observed in CI.
- Update tests to use 'zhack action idle' instead of ztest to improve
the reliability of the tests.
- Add additional log_note messages to test cases which have multiple
verification steps to make it clear which portion of a test failed
when reviewing the logs.
- Replace default_setup/cleanup_noexit calls with 'zpool create' and
'zpool destroy' calls to avoid additional unnecessary dataset
creation work.
- Update activity/noactivity check helper functions to use the
ZFS_LOAD_INFO_DEBUG information now available from 'zpool import'
to determine if this activity check ran and why. This is more
reliable in the CI than measuring the runtime.
- Removed all mmp tests from the zts-report.py exceptions list.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Akash B <akash-b@hpe.com>
As part of SPA_LOAD_IMPORT add an additional activity check to
detect simultaneous imports from different hosts. This check is
only required when the timing is such that there's no activity
for the the read-only tryimport check to detect. This extra
safety chceck operates as follows:
1. Repeats the following MMP check 10 times:
a. Write out an MMP uberblock with the best txg and a random
sequence id to all primary pool vdevs.
b. Verify a minimum number of good writes such that even if
the pool appears degraded on the remote host it will see
at least one of the updated MMP uberblocks.
c. Wait for the MMP interval this leaves a window for other
racing hosts to make similar modifications which can be
detected.
d. Call vdev_uberblock_load() to determine the best uberblock
to use, this should be the MMP uberblock just written.
e. Verify the txg and random sequeunce number match the MMP
uberblock written in 1a.
2. Restore the original MMP uberblocks. This allows the check
to be performed again if the pool fails to import for an
unrelated reason.
This change also includes some refactoring and minor improvements.
- Never try loading earlier txgs during import when the import
fails with EREMOTEIO or EINTER. These errors don't indicate
the txg is damaged but instead that its either in use on a
remote host or the import was interactively cancelled. No
rewind is also performed for EBADD which can result from a
stale trusted config when doing a verbatim import.
- Refactor the code for consistent logging of the multihost
activity check using spa_load_note() and console messages
indicating when the activity check was trigger and the result.
- Added MMP_*_MASK and MMP_SEQ_CLEAR() macros to allow easier
modification of the sequence number in an uberblock.
- Added ZFS_LOAD_INFO_DEBUG environment variable which can be
set to log to dump to stdout the spa_load_info nvlist returned
during import. This is used by the updated mmp test cases
to determine if an activity check was run and its result.
- Standardize the mmp messages similarly to make it easier to
find all the relevent mmp lines in the debug log.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Akash B <akash-b@hpe.com>
Tryimport adds a unique prefix to the pool name to avoid name
collisions. This makes it awkward to log user-friendly info
during a tryimport. Add a spa_load_name() function which can
be used to report the unmodified pool name.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Akash B <akash-b@hpe.com>
Move the "Starting import" log message in to the import block so
it's matched with the "Fiinshed importing" debug message.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Akash B <akash-b@hpe.com>
For a cleanly exported pools there exists a small window where
both systems may determine it's safe to import the pool and skip
the activity check. Only allow the check to be skipped when the
last imported hostid matches the systems hostid and the pool was
cleanly exported.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Akash B <akash-b@hpe.com>
They aren't used outside these very small blocks, and their initial
values are never used at all.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#17551
Free issue threads might block waiting for synchronous DDT, BRT or
GANG header reads. So unlike other taskqs using ZTI_SCALE to scale
with number of CPUs, here we also need some amount of threads to
potentially saturate pool reads. I am not sure we always want the
96 threads we had before ZTI_SCALE introduction at #11966 on small
systems, but lets make it at least 32.
While here, make free taskqs configurable, similar to read and
write ones.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rob Norris <robn@despairlabs.com>
Signed-off-by: Alexander Motin <alexander.motin@TrueNAS.com>
Closes#17903
Fix another instance where ZFS assumes multiple pages can be
mapped at once via zfs_kmap_local(), resulting in crashes and
potential memory corruption on HIGHMEM-enabled (typically 32-bit)
systems.
Reviewed-by: RageLtMan <rageltman@sempervictus>
Reviewed-by: Rob Norris <robn@despairlabs.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bspengler-oss <94915855+bspengler-oss@users.noreply.github.com>
Closes#15668Closes#18030
ZFS typically preserves proper LIFO ordering regarding map/unmap
operations that wrap the Linux kernel's kmap interfaces that
require such ordering, but one instance in abd_raidz_gen_iterate()
did not.
Similar issues have been fixed in the Linux kernel in the past,
see for instance CVE-2025-39899 for userfaultfd.
Reviewed-by: RageLtMan <rageltman@sempervictus>
Reviewed-by: Rob Norris <robn@despairlabs.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bspengler-oss <94915855+bspengler-oss@users.noreply.github.com>
Closes#15668Closes#18030
HIGHMEM kmap interfaces operate on only a single page at a time
yet ZFS hadn't accounted for this, resulting in crashes and
potential memory corruption on HIGHMEM (typically 32-bit) systems.
This was caught by PaX's KERNSEAL feature as it makes use of
HIGHMEM functionality on x64.
On typical 64-bit systems, this issue wouldn't have been observed,
as the map interfaces simply fall back to returning an address in
lowmem where the contiguous pages can be accessed directly.
Joint work with the PaX Team, tested by Mark van Dijk
Reviewed-by: RageLtMan <rageltman@sempervictus>
Reviewed-by: Rob Norris <robn@despairlabs.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bspengler-oss <94915855+bspengler-oss@users.noreply.github.com>
Closes#15668Closes#18030
Linux switched from -std=gnu89 to -std=gnu11 in 5.18
(torvalds/linux@e8c07082a8). We've always overridden that with gnu99
because we use some newer features.
More recent kernels are using C11 features in headers that we include.
GCC generally doesn't seem to care, but more recent versions of Clang
seem to be enforcing our gnu99 override more strictly, which breaks the
build in some configurations.
Just bumping our "override" to match the kernel seems to be the easiest
workaround. It's an effective no-op since 5.18, while still allowing us
to build on older kernels.
Sponsored-by: https://despairlabs.com/sponsor/
Signed-off-by: Rob Norris <robn@despairlabs.com>
Linux 6.18 has conflicting prototypes for various sha256_* and sha512_*
functions, which we get through a very long include chain. That's tough
to fix right now; easier is just to rename our internal functions.
Sponsored-by: https://despairlabs.com/sponsor/
Signed-off-by: Rob Norris <robn@despairlabs.com>
The namespace type has moved from the namespace ops struct to the
"common" base namespace struct. Detect this and define a macro that does
the right thing for both versions.
Sponsored-by: https://despairlabs.com/sponsor/
Signed-off-by: Rob Norris <robn@despairlabs.com>
Linux 6.18 removed write_cache_pages() without a usable replacement.
Here we implement a minimal zpl_write_cache_pages() that find the dirty
pages within the mapping, gets them into the expected state and hands
them off to zfs_putpage(), which handles the rest.
Sponsored-by: https://despairlabs.com/sponsor/
Signed-off-by: Rob Norris <robn@despairlabs.com>
ida_simple_get() and ida_simple_remove() are removed in 6.18. However,
since 4.19 they have been simple wrappers around ida_alloc() and
ida_free(), so we can just use those directly.
Sponsored-by: https://despairlabs.com/sponsor/
Signed-off-by: Rob Norris <robn@despairlabs.com>
zfs_aclset_common() might be called for newly created or not even
created vnodes, that triggers assertions on newer FreeBSD versions
with DEBUG_VFS_LOCKS included into INVARIANTS. In the first case
make sure to call vn_seqc_write_begin()/_end(), in the second just
skip the assertion.
The similar has to be done for project management IOCTL and file-
bases extended attributes, since those are not going through VFS.
Signed-off-by: Alexander Motin <alexander.motin@TrueNAS.com>
Closes#17722
Disable the aarch64 NEON SIMD intrinsics for kernel builds. Safely
using them in the kernel context requires saving/restoring the FPU
registers which is not currently done.
Additionally, remove the aarch64 optimized PREFETCH_L1 and PREFETCH_L2
instruction. Rely on the more portable compiler built ins.
This lets us remove the problematic workaround in the aarch64_compat.h
header which undefines the __aarch64__ macro.
Reviewed-by: Rob Norris <robn@despairlabs.com>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#17904Closes#17852
We need to specifically use the FX_XFLAG_* macros in zpl_ioctl_*attr()
codepaths, and the FS_*_FL macros in the zpl_ioctl_*flags() codepaths.
The earlier code just assumes the FS_*_FL macros for both codepaths.
The 6.17 kernel add a bitmask check in copy_fsxattr_from_user() that
exposed this error via failing 'projectquota' ZTS tests.
Reviewed-by: Alexander Motin <alexander.motin@TrueNAS.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#17884Closes#17869
The concurrent execution of feature_sync() can lead to a panic due
to an unprotected update of the feature refcount. Resolve this by
using the spa->spa_feat_stats_lock to synchronize the update of the
refcount.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#17184Closes#17632
This changes the basic search algorithm from a single search up and down
the tree to a full depth-first traversal to handle conditions where the
tree matches at a higher level but not a lower level.
Normally higher level blocks always point to matching blocks, but there
are cases where this does not happen:
1. Racing block pointer updates from dbuf_write_ready.
Before f664f1ee7f (#8946), both dbuf_write_ready and
dnode_next_offset held dn_struct_rwlock which protected against
pointer writes from concurrent syncs.
This no longer applies, so sync context can f.e. clear or fill all
L1->L0 BPs before the L2->L1 BP and higher BP's are updated.
dnode_free_range in particular can reach this case and skip over L1
blocks that need to be dirtied. Later, sync will panic in
free_children when trying to clear a non-dirty indirect block.
This case was found with ztest.
2. txg > 0, non-hole case. This is #11196.
Freeing blocks/dnodes breaks the assumption that a match at a higher
level implies a match at a lower level when filtering txg > 0.
Whenever some but not all L0 blocks are freed, the parent L1 block is
rewritten. Its updated L2->L1 BP reflects a newer birth txg.
Later when searching by txg, if the L1 block matches since the txg is
newer, it is possible that none of the remaining L1->L0 BPs match if
none have been updated.
The same behavior is possible with dnode search at L0.
This is reachable from dsl_destroy_head for synchronous freeing.
When this happens open context fails to free objects leaving sync
context stuck freeing potentially many objects.
This is also reachable from traverse_pool for extreme rewind where it
is theoretically possible that datasets not dirtied after txg are
skipped if the MOS has high enough indirection to trigger this case.
In both of these cases, without backtracking the search ends prematurely
as ESRCH result implies no more matches in the entire object.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Akash B <akash-b@hpe.com>
Signed-off-by: Robert Evans <evansr@google.com>
Closes#16025Closes#11196
ZVOLs don't support all block layer IO request types. Add a check for
the IO types we do support. Also, remove references to
io_is_secure_erase() since they are not supported on ZVOLs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <alexander.motin@TrueNAS.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#17803
The zvol blk-mq codepaths would erroneously send FLUSH and TRIM
commands down the read codepath, rather than write. This fixes
the issue, and updates the zvol_misc_fua test to verify that
sync writes are actually happening.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <alexander.motin@TrueNAS.com>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#17761Closes#17765
Provide an interface to retrieve the lowest and highest minimum
allocation size for the normal allocation class. This can be used
by external consumers of the DMU to estimate potential wasted
capacity when setting the recordsize for an object.
The new "min_alloc" and "max_alloc" keys are added to the pool
configuration and used by default_volblocksize() to warn when
an ineffecient block size is requested. For older kmods which
don't yet include the new keys fallback to the previous logic.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Motin <alexander.motin@TrueNAS.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#17758
We only have extremely narrow uses, so move it all into a single
function that does only what we need, with and without d_set_d_op().
Sponsored-by: https://despairlabs.com/sponsor/
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#17621
In FreeBSD there is now a pathconf name _PC_HAS_HIDDENSYSTEM.
This patch adds support for it to OpenZFS.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rick Macklem <rmacklem@uoguelph.ca>
Closes#17518
The field is subsequently accessed in zfs_mknode(), in
zfs_inherit_projid(). The Linux implementation of zfs_create_fs() has
this initialization already; there is no counterpart to
zfs_create_share_dir() that I can see.
Reported-by: KMSAN
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Rob Norris <rob.norris@klarasystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#17486
In syncing mode, zfs_putpages() would put the entire range of pages onto
the ZIL, then return VM_PAGER_OK for each page to the kernel. However,
an associated zil_commit() or txg sync had not happened at this point,
so the write may not actually be on disk.
So, we rework that case to use a ZIL commit callback, and do the
post-write work of undirtying the page and signaling completion there.
We return VM_PAGER_PEND to the kernel instead so it knows that we will
take care of it.
The original version of this (238eab7dc1) copied the Linux model and did
the cleanup in a ZIL callback for both async and sync. This was a
mistake, as FreeBSD does not have a separate "busy for writeback" flag
like Linux which keeps the page usable. The full sbusy flag locks the
entire page out until the itx callback fires, which for async is after
txg sync, which could be literal seconds in the future.
For the async case, the data is already on the DMU and the in-memory
ZIL, which is sufficient for async writeback, so the old method of
logging it without a callback, undirtying the page and returning is more
than sufficient and reclaims that lost performance.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Mark Johnston <markj@FreeBSD.org>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#17533
This causes async putpages to leave the pages sbusied for a long time,
which hurts concurrency. Revert for now until we have a better
approach.
This reverts commit 238eab7dc1.
Reported by: Ihor Antonov <ngor@hugpoint.tech>
Discussed with: Rob Norris <rob.norris@klarasystems.com>
References: freebsd/freebsd-src@738a9a7
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Mark Johnston <markj@FreeBSD.org>
Ported-by: Rob Norris <rob.norris@klarasystems.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#17533
Systems with a large number of CPU cores (192+) may trigger the large
allocation warning in multilist_create() on Linux. Silence the warning
by converting the allocation to vmem_alloc().
On Linux this results in a call to kvalloc() which will alloc vmem
for large allocations and kmem for small allocations.
On FreeBSD both vmem_alloc and kmem_alloc internally use the same
allocator so there is no functional change.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Motin <alexander.motin@TrueNAS.com>
Reviewed-by: Rob Norris <robn@despairlabs.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#17616
Allow zstd_mempool_init() to allocate using vmem_alloc() instead
of kmem_alloc() to silence the large allocation warning on Linux
during module load when the system has a large number of CPUs.
It's not at all clear to me that scaling the allocation size with
the number of CPUs is beneficial and that should be evaluated.
But for the moment this should resolve the warning without
introducing any unexpected side effects.
Reviewed-by: Alexander Motin <alexander.motin@TrueNAS.com>
Reviewed-by: Rob Norris <robn@despairlabs.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#17620Closes#11557
03987f71e3 (#16069) added a workaround to get the blk-mq hardware
context for older kernels that don't cache it in the struct request.
However, this workaround appears to be incomplete.
In 4.19, the rq data context is optional. If its not initialised, then
the cached rq->cpu will be -1, and so using it to index into mq_map
causes a crash.
Given that the upstream 4.19 is now in extended LTS and rarely seen,
RHEL8 4.18+ has long carried "modern" blk-mq support, and the cached
hardware context has been available since 5.1, I'm not going to huge
lengths to get queue selection correct for the very few people that are
likely to feel it. To that end, we simply call raw_smp_processor_id() to
get a valid CPU id and use that instead.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <alexander.motin@TrueNAS.com>
Reviewed-by: Paul Dagnelie <paul.dagnelie@klarasystems.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Closes#17597
The structure of zfs_putpage() and its callers is tricky to follow.
There's a lot more we could do to improve it, but at least now we have
some description of one of the trickier bits.
Writing this exposed a very subtle bug: most async pages pushed out
through zpl_putpages() would go to the ZIL with commit=false, which can
yield a less-efficient write policy. So this commit updates that too.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <alexander.motin@TrueNAS.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#17584
For async page writeback, we do not need to wait for the page to be on
disk before returning to the caller; it's enough that the data from the
dirty page be on the DMU and in the in-memory ZIL, just like any other
write.
So, if this is not a syncing write, don't add a callback to the itx, and
instead just unlock the page immediately.
(This is effectively the same concept used for FreeBSD in d323fbf49c).
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <alexander.motin@TrueNAS.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#17584Closes#14290
All this machinery is there to try to understand when there an async
writeback waiting to complete because the intent log callbacks are still
outstanding, and force them with a timely zil_commit(). The next commit
fixes this properly, so there's no need for all this extra housekeeping.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <alexander.motin@TrueNAS.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#17584
The linux kernel modules haven't been building successfully when the
build occurs in a separate directory than the source code, which is a
common build pattern in Linux. Was not able to determine the root cause,
but the %.o targets in subdirectories are no longer being matched by the
pattern targets in the Linux Kbuild system. This change fixes the issue
by dynamically creating the missing ones inside our Kbuild.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#17517
This allows to change the meaning of priority differences in FreeBSD
without requiring code changes in ZFS.
This upstreams commit fd141584cf89d7d2 from FreeBSD src.
Sponsored-by: The FreeBSD Foundation
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Olivier Certner <olce@FreeBSD.org>
Closes#17489
Older kernel versions run make outside of the build directory. This
works since all paths are absolute. Relative paths will fail in such
a scenario.
Use an absolute path to the objtool wrapper as well, since the
relative path breaks the build on older kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#17541
Linux 5.16 by default fails the build on objtool warnings. We have
known and understood objtool warnings we can't fix without
involving Linux maintainers.
To work around this we introduce an objtool wrapper script which
removes the `--Werror` flag.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#17456
It is not right, but there are few examples when TX is aborted
after being assigned in case of error. To handle it better on
production systems add extra cleanup steps.
While here, replace couple dmu_tx_abort() in simple cases.
Reviewed-by: Rob Norris <robn@despairlabs.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#17438
This allows to rewrite content of specified file(s) as-is without
modifications, but at a different location, compression, checksum,
dedup, copies and other parameter values. It is faster than read
plus write, since it does not require data copying to user-space.
It is also faster for sync=always datasets, since without data
modification it does not require ZIL writing. Also since it is
protected by normal range range locks, it can be done under any
other load. Also it does not affect file's modification time or
other properties.
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rob Norris <robn@despairlabs.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#17443
Avoid calling dbuf_evict_one() from memory reclaim contexts (e.g. Linux
kswapd, FreeBSD pagedaemon). This prevents deadlock caused by reclaim
threads waiting for the dbuf hash lock in the call sequence:
dbuf_evict_one -> dbuf_destroy -> arc_buf_destroy
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <alexander.motin@TrueNAS.com>
Signed-off-by: Kaitlin Hoang <kthoang@amazon.com>
Closes#17561
Linux kernel shrinker in the context of null/root memcg does not scan
dentry and inode caches added by a task running in non-root memcg. For
ZFS this means that dnode cache routinely overflows, evicting valuable
meta/data and putting additional memory pressure on the system.
This patch restores zfs_prune_aliases as fallback when the kernel
shrinker does nothing, enabling zfs to actually free dnodes. Moreover,
it (indirectly) calls arc_evict when dnode_size > dnode_limit.
Reviewed-by: Rob Norris <robn@despairlabs.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gionatan Danti <g.danti@assyoma.it>
Closes#17487Closes#17542
