409 lines
7.7 KiB
Plaintext
409 lines
7.7 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
/dts-v1/;
|
|
|
|
#include "msm8916-pm8916.dtsi"
|
|
#include "msm8916-modem-qdsp6.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/leds/common.h>
|
|
|
|
/ {
|
|
model = "Longcheer L8150";
|
|
compatible = "longcheer,l8150", "qcom,msm8916-v1-qrd/9-v1", "qcom,msm8916";
|
|
chassis-type = "handset";
|
|
|
|
aliases {
|
|
mmc0 = &sdhc_1; /* eMMC */
|
|
mmc1 = &sdhc_2; /* SD card */
|
|
serial0 = &blsp_uart2;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0";
|
|
};
|
|
|
|
/*
|
|
* For some reason, the signed wcnss firmware is not relocatable.
|
|
* It must be loaded at 0x8b600000. Unfortunately, this also means that
|
|
* mpss_mem does not fit when loaded to the typical address at 0x86800000.
|
|
*
|
|
* Load wcnss_mem to the fixed address and relocate mpss_mem to the next
|
|
* working higher address. For some reason the modem firmware does not
|
|
* boot when placed at 0x8a800000 to 0x8e800000.
|
|
*/
|
|
reserved-memory {
|
|
/delete-node/ mpss@86800000;
|
|
/delete-node/ wcnss;
|
|
|
|
wcnss_mem: wcnss@8b600000 {
|
|
reg = <0x0 0x8b600000 0x0 0x600000>;
|
|
no-map;
|
|
};
|
|
|
|
mpss_mem: mpss@8e800000 {
|
|
reg = <0x0 0x8e800000 0x0 0x5000000>;
|
|
no-map;
|
|
};
|
|
};
|
|
|
|
battery: battery {
|
|
compatible = "simple-battery";
|
|
voltage-min-design-microvolt = <3400000>;
|
|
voltage-max-design-microvolt = <4350000>;
|
|
energy-full-design-microwatt-hours = <9500000>;
|
|
charge-full-design-microamp-hours = <2500000>;
|
|
|
|
ocv-capacity-celsius = <25>;
|
|
ocv-capacity-table-0 = <4330000 100>, <4265000 95>,
|
|
<4208000 90>, <4153000 85>, <4100000 80>, <4049000 75>,
|
|
<4001000 70>, <3962000 65>, <3919000 60>, <3872000 55>,
|
|
<3839000 50>, <3817000 45>, <3798000 40>, <3783000 35>,
|
|
<3767000 30>, <3747000 25>, <3729000 20>, <3709000 16>,
|
|
<3688000 13>, <3681000 11>, <3680000 10>, <3679000 9>,
|
|
<3677000 8>, <3674000 7>, <3666000 6>, <3641000 5>,
|
|
<3597000 4>, <3537000 3>, <3457000 2>, <3336000 1>,
|
|
<3000000 0>;
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gpio_keys_default>;
|
|
|
|
label = "GPIO Buttons";
|
|
|
|
button-volume-up {
|
|
label = "Volume Up";
|
|
gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_VOLUMEUP>;
|
|
};
|
|
};
|
|
|
|
reg_ctp: regulator-ctp {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "ctp";
|
|
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
|
|
gpio = <&tlmm 17 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&ctp_pwr_en_default>;
|
|
};
|
|
|
|
flash-led-controller {
|
|
compatible = "sgmicro,sgm3140";
|
|
flash-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
|
|
enable-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&camera_flash_default>;
|
|
|
|
flash_led: led {
|
|
function = LED_FUNCTION_FLASH;
|
|
color = <LED_COLOR_ID_WHITE>;
|
|
flash-max-timeout-us = <250000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&blsp_i2c1 {
|
|
status = "okay";
|
|
|
|
led-controller@45 {
|
|
compatible = "awinic,aw2013";
|
|
reg = <0x45>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
vcc-supply = <&pm8916_l17>;
|
|
vio-supply = <&pm8916_l6>;
|
|
|
|
led@0 {
|
|
reg = <0>;
|
|
led-max-microamp = <5000>;
|
|
function = LED_FUNCTION_INDICATOR;
|
|
color = <LED_COLOR_ID_RED>;
|
|
};
|
|
|
|
led@1 {
|
|
reg = <1>;
|
|
led-max-microamp = <5000>;
|
|
function = LED_FUNCTION_INDICATOR;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
};
|
|
|
|
led@2 {
|
|
reg = <2>;
|
|
led-max-microamp = <5000>;
|
|
function = LED_FUNCTION_INDICATOR;
|
|
color = <LED_COLOR_ID_BLUE>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&blsp_i2c2 {
|
|
status = "okay";
|
|
|
|
accelerometer@10 {
|
|
compatible = "bosch,bmc156_accel";
|
|
reg = <0x10>;
|
|
|
|
/*
|
|
* For some reason the interrupt line is usually not connected
|
|
* to the BMC156. However, there are two pads next to the chip
|
|
* that can be shorted to make it work if needed.
|
|
*
|
|
* interrupt-parent = <&tlmm>;
|
|
* interrupts = <116 IRQ_TYPE_EDGE_RISING>;
|
|
*/
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&accel_int_default>;
|
|
|
|
vdd-supply = <&pm8916_l17>;
|
|
vddio-supply = <&pm8916_l6>;
|
|
|
|
mount-matrix = "0", "1", "0",
|
|
"-1", "0", "0",
|
|
"0", "0", "1";
|
|
};
|
|
|
|
magnetometer@12 {
|
|
compatible = "bosch,bmc156_magn";
|
|
reg = <0x12>;
|
|
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <113 IRQ_TYPE_EDGE_RISING>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&magn_int_default>;
|
|
|
|
vdd-supply = <&pm8916_l17>;
|
|
vddio-supply = <&pm8916_l6>;
|
|
};
|
|
|
|
light-sensor@23 {
|
|
compatible = "liteon,ltr559";
|
|
reg = <0x23>;
|
|
proximity-near-level = <75>;
|
|
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <115 IRQ_TYPE_EDGE_FALLING>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&light_int_default>;
|
|
|
|
vdd-supply = <&pm8916_l17>;
|
|
vddio-supply = <&pm8916_l6>;
|
|
};
|
|
|
|
gyroscope@68 {
|
|
compatible = "bosch,bmg160";
|
|
reg = <0x68>;
|
|
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <23 IRQ_TYPE_EDGE_RISING>,
|
|
<22 IRQ_TYPE_EDGE_RISING>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gyro_int_default>;
|
|
|
|
vdd-supply = <&pm8916_l17>;
|
|
vddio-supply = <&pm8916_l6>;
|
|
};
|
|
};
|
|
|
|
&blsp_i2c5 {
|
|
status = "okay";
|
|
|
|
rmi4@20 {
|
|
compatible = "syna,rmi4-i2c";
|
|
reg = <0x20>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
|
|
|
|
vdd-supply = <®_ctp>;
|
|
vio-supply = <&pm8916_l6>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&tp_int_default>;
|
|
|
|
syna,startup-delay-ms = <10>;
|
|
|
|
rmi4-f01@1 {
|
|
reg = <0x1>;
|
|
syna,nosleep-mode = <1>; /* Allow sleeping */
|
|
};
|
|
|
|
rmi4-f12@12 {
|
|
reg = <0x12>;
|
|
syna,sensor-type = <1>; /* Touchscreen */
|
|
};
|
|
};
|
|
};
|
|
|
|
&blsp_uart2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&pm8916_bms {
|
|
status = "okay";
|
|
|
|
monitored-battery = <&battery>;
|
|
power-supplies = <&pm8916_charger>;
|
|
};
|
|
|
|
&pm8916_charger {
|
|
status = "okay";
|
|
|
|
monitored-battery = <&battery>;
|
|
|
|
qcom,fast-charge-safe-current = <900000>;
|
|
qcom,fast-charge-safe-voltage = <4300000>;
|
|
};
|
|
|
|
&pm8916_codec {
|
|
qcom,micbias-lvl = <2800>;
|
|
qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
|
|
qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
|
|
qcom,hphl-jack-type-normally-open;
|
|
};
|
|
|
|
&pm8916_resin {
|
|
status = "okay";
|
|
linux,code = <KEY_VOLUMEDOWN>;
|
|
};
|
|
|
|
&pm8916_rpm_regulators {
|
|
pm8916_l17: l17 {
|
|
regulator-min-microvolt = <2850000>;
|
|
regulator-max-microvolt = <2850000>;
|
|
};
|
|
};
|
|
|
|
&pm8916_vib {
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhc_1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhc_2 {
|
|
status = "okay";
|
|
non-removable;
|
|
};
|
|
|
|
&sound {
|
|
audio-routing =
|
|
"AMIC1", "MIC BIAS Internal1",
|
|
"AMIC2", "MIC BIAS Internal2",
|
|
"AMIC3", "MIC BIAS Internal3";
|
|
};
|
|
|
|
&usb {
|
|
status = "okay";
|
|
dr_mode = "peripheral";
|
|
extcon = <&pm8916_charger>;
|
|
};
|
|
|
|
&usb_hs_phy {
|
|
extcon = <&pm8916_charger>;
|
|
};
|
|
|
|
&venus {
|
|
status = "okay";
|
|
};
|
|
|
|
&venus_mem {
|
|
status = "okay";
|
|
};
|
|
|
|
&wcnss {
|
|
status = "okay";
|
|
};
|
|
|
|
&wcnss_iris {
|
|
compatible = "qcom,wcn3620";
|
|
};
|
|
|
|
&wcnss_mem {
|
|
status = "okay";
|
|
};
|
|
|
|
&tlmm {
|
|
accel_int_default: accel-int-default-state {
|
|
pins = "gpio116";
|
|
function = "gpio";
|
|
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
|
|
camera_flash_default: camera-flash-default-state {
|
|
pins = "gpio31", "gpio32";
|
|
function = "gpio";
|
|
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
|
|
ctp_pwr_en_default: ctp-pwr-en-default-state {
|
|
pins = "gpio17";
|
|
function = "gpio";
|
|
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
|
|
gpio_keys_default: gpio-keys-default-state {
|
|
pins = "gpio107";
|
|
function = "gpio";
|
|
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
gyro_int_default: gyro-int-default-state {
|
|
pins = "gpio22", "gpio23";
|
|
function = "gpio";
|
|
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
|
|
light_int_default: light-int-default-state {
|
|
pins = "gpio115";
|
|
function = "gpio";
|
|
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
|
|
magn_int_default: magn-int-default-state {
|
|
pins = "gpio113";
|
|
function = "gpio";
|
|
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
|
|
tp_int_default: tp-int-default-state {
|
|
pins = "gpio13";
|
|
function = "gpio";
|
|
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
};
|