155 lines
2.8 KiB
Plaintext
155 lines
2.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
/dts-v1/;
|
|
#include "bcm2837.dtsi"
|
|
#include "bcm2836-rpi.dtsi"
|
|
#include "bcm283x-rpi-led-deprecated.dtsi"
|
|
#include "bcm283x-rpi-smsc9514.dtsi"
|
|
#include "bcm283x-rpi-usb-host.dtsi"
|
|
#include "bcm283x-rpi-wifi-bt.dtsi"
|
|
|
|
/ {
|
|
compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
|
|
model = "Raspberry Pi 3 Model B";
|
|
|
|
chosen {
|
|
/* 8250 auxiliary UART instead of pl011 */
|
|
stdout-path = "serial1:115200n8";
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0 0x40000000>;
|
|
};
|
|
};
|
|
|
|
&bt {
|
|
shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
&firmware {
|
|
expgpio: gpio {
|
|
compatible = "raspberrypi,firmware-gpio";
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
gpio-line-names = "BT_ON",
|
|
"WL_ON",
|
|
"STATUS_LED",
|
|
"LAN_RUN",
|
|
"HDMI_HPD_N",
|
|
"CAM_GPIO0",
|
|
"CAM_GPIO1",
|
|
"PWR_LOW_N";
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&gpio {
|
|
/*
|
|
* Taken from rpi_SCH_3b_1p2_reduced.pdf and
|
|
* the official GPU firmware DT blob.
|
|
*
|
|
* Legend:
|
|
* "FOO" = GPIO line named "FOO" on the schematic
|
|
* "FOO_N" = GPIO line named "FOO" on schematic, active low
|
|
*/
|
|
gpio-line-names = "ID_SDA",
|
|
"ID_SCL",
|
|
"SDA1",
|
|
"SCL1",
|
|
"GPIO_GCLK",
|
|
"GPIO5",
|
|
"GPIO6",
|
|
"SPI_CE1_N",
|
|
"SPI_CE0_N",
|
|
"SPI_MISO",
|
|
"SPI_MOSI",
|
|
"SPI_SCLK",
|
|
"GPIO12",
|
|
"GPIO13",
|
|
/* Serial port */
|
|
"TXD1",
|
|
"RXD1",
|
|
"GPIO16",
|
|
"GPIO17",
|
|
"GPIO18",
|
|
"GPIO19",
|
|
"GPIO20",
|
|
"GPIO21",
|
|
"GPIO22",
|
|
"GPIO23",
|
|
"GPIO24",
|
|
"GPIO25",
|
|
"GPIO26",
|
|
"GPIO27",
|
|
"", /* GPIO 28 */
|
|
"LAN_RUN_BOOT",
|
|
/* Used by BT module */
|
|
"CTS0",
|
|
"RTS0",
|
|
"TXD0",
|
|
"RXD0",
|
|
/* Used by Wifi */
|
|
"SD1_CLK",
|
|
"SD1_CMD",
|
|
"SD1_DATA0",
|
|
"SD1_DATA1",
|
|
"SD1_DATA2",
|
|
"SD1_DATA3",
|
|
"PWM0_OUT",
|
|
"PWM1_OUT",
|
|
"ETH_CLK",
|
|
"WIFI_CLK",
|
|
"SDA0",
|
|
"SCL0",
|
|
"SMPS_SCL",
|
|
"SMPS_SDA",
|
|
/* Used by SD Card */
|
|
"SD_CLK_R",
|
|
"SD_CMD_R",
|
|
"SD_DATA0_R",
|
|
"SD_DATA1_R",
|
|
"SD_DATA2_R",
|
|
"SD_DATA3_R";
|
|
};
|
|
|
|
&pwm {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
|
|
status = "okay";
|
|
};
|
|
|
|
&hdmi {
|
|
hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>;
|
|
power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
|
|
status = "okay";
|
|
};
|
|
|
|
&led_act {
|
|
gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
/* uart0 communicates with the BT module */
|
|
&uart0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
|
|
};
|
|
|
|
/* uart1 is mapped to the pin header */
|
|
&uart1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart1_gpio14>;
|
|
status = "okay";
|
|
};
|
|
|
|
/* SDHOST is used to drive the SD card */
|
|
&sdhost {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sdhost_gpio48>;
|
|
status = "okay";
|
|
bus-width = <4>;
|
|
};
|
|
|
|
&wifi_pwrseq {
|
|
reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
|
|
};
|