196 lines
6.1 KiB
YAML
196 lines
6.1 KiB
YAML
# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/regulator/nxp,pca9450-regulator.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: NXP PCA9450A/B/C Power Management Integrated Circuit regulators
|
|
|
|
maintainers:
|
|
- Robin Gong <yibin.gong@nxp.com>
|
|
|
|
description: |
|
|
Regulator nodes should be named to BUCK_<number> and LDO_<number>. The
|
|
definition for each of these nodes is defined using the standard
|
|
binding for regulators at
|
|
Documentation/devicetree/bindings/regulator/regulator.txt.
|
|
Datasheet is available at
|
|
https://www.nxp.com/docs/en/data-sheet/PCA9450DS.pdf
|
|
|
|
# The valid names for PCA9450 regulator nodes are:
|
|
# BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6,
|
|
# LDO1, LDO2, LDO3, LDO4, LDO5
|
|
# Note: Buck3 removed on PCA9450B and connect with Buck1 on PCA9450C.
|
|
|
|
properties:
|
|
compatible:
|
|
enum:
|
|
- nxp,pca9450a
|
|
- nxp,pca9450b
|
|
- nxp,pca9450c
|
|
|
|
reg:
|
|
maxItems: 1
|
|
|
|
interrupts:
|
|
maxItems: 1
|
|
|
|
regulators:
|
|
type: object
|
|
description: |
|
|
list of regulators provided by this controller
|
|
|
|
patternProperties:
|
|
"^LDO[1-5]$":
|
|
type: object
|
|
$ref: regulator.yaml#
|
|
description:
|
|
Properties for single LDO regulator.
|
|
|
|
unevaluatedProperties: false
|
|
|
|
"^BUCK[1-6]$":
|
|
type: object
|
|
$ref: regulator.yaml#
|
|
description:
|
|
Properties for single BUCK regulator.
|
|
|
|
properties:
|
|
nxp,dvs-run-voltage:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 600000
|
|
maximum: 2187500
|
|
description:
|
|
PMIC default "RUN" state voltage in uV. Only Buck1~3 have such
|
|
dvs(dynamic voltage scaling) property.
|
|
|
|
nxp,dvs-standby-voltage:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 600000
|
|
maximum: 2187500
|
|
description:
|
|
PMIC default "STANDBY" state voltage in uV. Only Buck1~3 have such
|
|
dvs(dynamic voltage scaling) property.
|
|
|
|
unevaluatedProperties: false
|
|
|
|
additionalProperties: false
|
|
|
|
sd-vsel-gpios:
|
|
description: GPIO that is used to switch LDO5 between being configured by
|
|
LDO5CTRL_L or LDO5CTRL_H register. Use this if the SD_VSEL signal is
|
|
connected to a host GPIO.
|
|
|
|
nxp,i2c-lt-enable:
|
|
type: boolean
|
|
description:
|
|
Indicates that the I2C Level Translator is used.
|
|
|
|
nxp,wdog_b-warm-reset:
|
|
type: boolean
|
|
description:
|
|
When WDOG_B signal is asserted a warm reset will be done instead of cold
|
|
reset.
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- interrupts
|
|
- regulators
|
|
|
|
additionalProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
|
i2c {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
pmic: pmic@25 {
|
|
compatible = "nxp,pca9450b";
|
|
reg = <0x25>;
|
|
pinctrl-0 = <&pinctrl_pmic>;
|
|
interrupt-parent = <&gpio1>;
|
|
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
|
|
|
|
regulators {
|
|
buck1: BUCK1 {
|
|
regulator-name = "BUCK1";
|
|
regulator-min-microvolt = <600000>;
|
|
regulator-max-microvolt = <2187500>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
regulator-ramp-delay = <3125>;
|
|
};
|
|
buck2: BUCK2 {
|
|
regulator-name = "BUCK2";
|
|
regulator-min-microvolt = <600000>;
|
|
regulator-max-microvolt = <2187500>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
regulator-ramp-delay = <3125>;
|
|
nxp,dvs-run-voltage = <950000>;
|
|
nxp,dvs-standby-voltage = <850000>;
|
|
};
|
|
buck4: BUCK4 {
|
|
regulator-name = "BUCK4";
|
|
regulator-min-microvolt = <600000>;
|
|
regulator-max-microvolt = <3400000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
buck5: BUCK5 {
|
|
regulator-name = "BUCK5";
|
|
regulator-min-microvolt = <600000>;
|
|
regulator-max-microvolt = <3400000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
buck6: BUCK6 {
|
|
regulator-name = "BUCK6";
|
|
regulator-min-microvolt = <600000>;
|
|
regulator-max-microvolt = <3400000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo1: LDO1 {
|
|
regulator-name = "LDO1";
|
|
regulator-min-microvolt = <1600000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
ldo2: LDO2 {
|
|
regulator-name = "LDO2";
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <1150000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
ldo3: LDO3 {
|
|
regulator-name = "LDO3";
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
ldo4: LDO4 {
|
|
regulator-name = "LDO4";
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
ldo5: LDO5 {
|
|
regulator-name = "LDO5";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
};
|
|
};
|
|
};
|