188 lines
6.9 KiB
YAML
188 lines
6.9 KiB
YAML
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
|
|
# Copyright 2023 Realtek Semiconductor Corporation
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/pinctrl/realtek,rtd1319d-pinctrl.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: Realtek DHC RTD1319D Pin Controller
|
|
|
|
maintainers:
|
|
- TY Chang <tychang@realtek.com>
|
|
|
|
description:
|
|
The Realtek DHC RTD1319D is a high-definition media processor SoC. The
|
|
RTD1319D pin controller is used to control pin function, pull up/down
|
|
resistor, drive strength, schmitt trigger and power source.
|
|
|
|
properties:
|
|
compatible:
|
|
const: realtek,rtd1319d-pinctrl
|
|
|
|
reg:
|
|
maxItems: 1
|
|
|
|
patternProperties:
|
|
'-pins$':
|
|
type: object
|
|
allOf:
|
|
- $ref: pincfg-node.yaml#
|
|
- $ref: pinmux-node.yaml#
|
|
|
|
properties:
|
|
pins:
|
|
items:
|
|
enum: [ gpio_0, gpio_1, gpio_2, gpio_3, gpio_4, gpio_5, gpio_6, gpio_7,
|
|
gpio_8, gpio_9, gpio_10, gpio_11, gpio_12, gpio_13, gpio_14,
|
|
gpio_15, gpio_16, gpio_17, gpio_18, gpio_19, gpio_20, gpio_21,
|
|
gpio_22, gpio_23, usb_cc2, gpio_25, gpio_26, gpio_27, gpio_28,
|
|
gpio_29, gpio_30, gpio_31, gpio_32, gpio_33, gpio_34, gpio_35,
|
|
hif_data, hif_en, hif_rdy, hif_clk, gpio_40, gpio_41, gpio_42,
|
|
gpio_43, gpio_44, gpio_45, gpio_46, gpio_47, gpio_48, gpio_49,
|
|
gpio_50, usb_cc1, gpio_52, gpio_53, ir_rx, ur0_rx, ur0_tx,
|
|
gpio_57, gpio_58, gpio_59, gpio_60, gpio_61, gpio_62, gpio_63,
|
|
gpio_64, emmc_rst_n, emmc_dd_sb, emmc_clk, emmc_cmd, emmc_data_0,
|
|
emmc_data_1, emmc_data_2, emmc_data_3, emmc_data_4, emmc_data_5,
|
|
emmc_data_6, emmc_data_7, dummy, gpio_78, gpio_79, gpio_80,
|
|
gpio_81, ur2_loc, gspi_loc, hi_width, sf_en, arm_trace_dbg_en,
|
|
ejtag_aucpu_loc, ejtag_acpu_loc, ejtag_vcpu_loc, ejtag_scpu_loc,
|
|
dmic_loc, ejtag_secpu_loc, vtc_dmic_loc, vtc_tdm_loc, vtc_i2si_loc,
|
|
tdm_ai_loc, ai_loc, spdif_loc, hif_en_loc, sc0_loc, sc1_loc,
|
|
scan_switch, wd_rset, boot_sel, reset_n, testmode ]
|
|
|
|
function:
|
|
enum: [ gpio, nf, emmc, tp0, tp1, sc0, sc0_data0, sc0_data1, sc0_data2,
|
|
sc1, sc1_data0, sc1_data1, sc1_data2, ao, gspi_loc0, gspi_loc1,
|
|
uart0, uart1, uart2_loc0, uart2_loc1, i2c0, i2c1, i2c3, i2c4,
|
|
i2c5, pcie1, sdio, etn_led, etn_phy, spi, pwm0_loc0, pwm0_loc1,
|
|
pwm1_loc0, pwm1_loc1, pwm2_loc0, pwm2_loc1, pwm3_loc0, pwm3_loc1,
|
|
qam_agc_if0, qam_agc_if1, spdif_optical_loc0, spdif_optical_loc1,
|
|
usb_cc1, usb_cc2, vfd, sd, dmic_loc0, dmic_loc1, ai_loc0, ai_loc1,
|
|
tdm_ai_loc0, tdm_ai_loc1, hi_loc0, hi_m, vtc_i2so, vtc_i2si_loc0,
|
|
vtc_i2si_loc1, vtc_dmic_loc0, vtc_dmic_loc1, vtc_tdm_loc0,
|
|
vtc_tdm_loc1, dc_fan, pll_test_loc0, pll_test_loc1, ir_rx,
|
|
uart2_disable, gspi_disable, hi_width_disable, hi_width_1bit,
|
|
sf_disable, sf_enable, scpu_ejtag_loc0, scpu_ejtag_loc1,
|
|
scpu_ejtag_loc2, acpu_ejtag_loc0, acpu_ejtag_loc1, acpu_ejtag_loc2,
|
|
vcpu_ejtag_loc0, vcpu_ejtag_loc1, vcpu_ejtag_loc2, secpu_ejtag_loc0,
|
|
secpu_ejtag_loc1, secpu_ejtag_loc2, aucpu_ejtag_loc0, aucpu_ejtag_loc1,
|
|
aucpu_ejtag_loc2, iso_tristate, dbg_out0, dbg_out1, standby_dbg,
|
|
spdif, arm_trace_debug_disable, arm_trace_debug_enable,
|
|
aucpu_ejtag_disable, acpu_ejtag_disable, vcpu_ejtag_disable,
|
|
scpu_ejtag_disable, secpu_ejtag_disable, vtc_dmic_loc_disable,
|
|
vtc_tdm_disable, vtc_i2si_disable, tdm_ai_disable, ai_disable,
|
|
spdif_disable, hif_disable, hif_enable, test_loop, pmic_pwrup ]
|
|
|
|
drive-strength:
|
|
enum: [4, 8]
|
|
|
|
bias-pull-down: true
|
|
|
|
bias-pull-up: true
|
|
|
|
bias-disable: true
|
|
|
|
input-schmitt-enable: true
|
|
|
|
input-schmitt-disable: true
|
|
|
|
drive-push-pull: true
|
|
|
|
power-source:
|
|
description: |
|
|
Valid arguments are described as below:
|
|
0: power supply of 1.8V
|
|
1: power supply of 3.3V
|
|
enum: [0, 1]
|
|
|
|
realtek,drive-strength-p:
|
|
description: |
|
|
Some of pins can be driven using the P-MOS and N-MOS transistor to
|
|
achieve finer adjustments. The block-diagram representation is as
|
|
follows:
|
|
VDD
|
|
|
|
|
||--+
|
|
+-----o|| P-MOS-FET
|
|
| ||--+
|
|
IN --+ +----- out
|
|
| ||--+
|
|
+------|| N-MOS-FET
|
|
||--+
|
|
|
|
|
GND
|
|
The driving strength of the P-MOS/N-MOS transistors impacts the
|
|
waveform's rise/fall times. Greater driving strength results in
|
|
shorter rise/fall times. Each P-MOS and N-MOS transistor offers
|
|
8 configurable levels (0 to 7), with higher values indicating
|
|
greater driving strength, contributing to achieving the desired
|
|
speed.
|
|
|
|
The realtek,drive-strength-p is used to control the driving strength
|
|
of the P-MOS output.
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 0
|
|
maximum: 7
|
|
|
|
realtek,drive-strength-n:
|
|
description: |
|
|
Similar to the realtek,drive-strength-p, the realtek,drive-strength-n
|
|
is used to control the driving strength of the N-MOS output.
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
minimum: 0
|
|
maximum: 7
|
|
|
|
realtek,duty-cycle:
|
|
description: |
|
|
An integer describing the level to adjust output duty cycle, controlling
|
|
the proportion of positive and negative waveforms in nanoseconds.
|
|
Valid arguments are described as below:
|
|
0: 0ns
|
|
2: + 0.25ns
|
|
3: + 0.5ns
|
|
4: -0.25ns
|
|
5: -0.5ns
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
enum: [ 0, 2, 3, 4, 5 ]
|
|
|
|
required:
|
|
- pins
|
|
|
|
additionalProperties: false
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
|
|
additionalProperties: false
|
|
|
|
examples:
|
|
- |
|
|
pinctrl@4e000 {
|
|
compatible = "realtek,rtd1319d-pinctrl";
|
|
reg = <0x4e000 0x130>;
|
|
|
|
emmc-hs200-pins {
|
|
pins = "emmc_clk",
|
|
"emmc_cmd",
|
|
"emmc_data_0",
|
|
"emmc_data_1",
|
|
"emmc_data_2",
|
|
"emmc_data_3",
|
|
"emmc_data_4",
|
|
"emmc_data_5",
|
|
"emmc_data_6",
|
|
"emmc_data_7";
|
|
function = "emmc";
|
|
realtek,drive-strength-p = <0x2>;
|
|
realtek,drive-strength-n = <0x2>;
|
|
};
|
|
|
|
i2c-0-pins {
|
|
pins = "gpio_12",
|
|
"gpio_13";
|
|
function = "i2c0";
|
|
drive-strength = <4>;
|
|
};
|
|
};
|