mirror_ubuntu-kernels/drivers/clocksource/timer-ti-dm-systimer.c

853 lines
22 KiB
C

// SPDX-License-Identifier: GPL-2.0+
#include <linux/clk.h>
#include <linux/clocksource.h>
#include <linux/clockchips.h>
#include <linux/cpuhotplug.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/iopoll.h>
#include <linux/err.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/sched_clock.h>
#include <linux/clk/clk-conf.h>
#include <clocksource/timer-ti-dm.h>
#include <dt-bindings/bus/ti-sysc.h>
/* For type1, set SYSC_OMAP2_CLOCKACTIVITY for fck off on idle, l4 clock on */
#define DMTIMER_TYPE1_ENABLE ((1 << 9) | (SYSC_IDLE_SMART << 3) | \
SYSC_OMAP2_ENAWAKEUP | SYSC_OMAP2_AUTOIDLE)
#define DMTIMER_TYPE1_DISABLE (SYSC_OMAP2_SOFTRESET | SYSC_OMAP2_AUTOIDLE)
#define DMTIMER_TYPE2_ENABLE (SYSC_IDLE_SMART_WKUP << 2)
#define DMTIMER_RESET_WAIT 100000
#define DMTIMER_INST_DONT_CARE ~0U
static int counter_32k;
static u32 clocksource;
static u32 clockevent;
/*
* Subset of the timer registers we use. Note that the register offsets
* depend on the timer revision detected.
*/
struct dmtimer_systimer {
void __iomem *base;
u8 sysc;
u8 irq_stat;
u8 irq_ena;
u8 pend;
u8 load;
u8 counter;
u8 ctrl;
u8 wakeup;
u8 ifctrl;
struct clk *fck;
struct clk *ick;
unsigned long rate;
};
struct dmtimer_clockevent {
struct clock_event_device dev;
struct dmtimer_systimer t;
u32 period;
};
struct dmtimer_clocksource {
struct clocksource dev;
struct dmtimer_systimer t;
unsigned int loadval;
};
/* Assumes v1 ip if bits [31:16] are zero */
static bool dmtimer_systimer_revision1(struct dmtimer_systimer *t)
{
u32 tidr = readl_relaxed(t->base);
return !(tidr >> 16);
}
static void dmtimer_systimer_enable(struct dmtimer_systimer *t)
{
u32 val;
if (dmtimer_systimer_revision1(t))
val = DMTIMER_TYPE1_ENABLE;
else
val = DMTIMER_TYPE2_ENABLE;
writel_relaxed(val, t->base + t->sysc);
}
static void dmtimer_systimer_disable(struct dmtimer_systimer *t)
{
if (!dmtimer_systimer_revision1(t))
return;
writel_relaxed(DMTIMER_TYPE1_DISABLE, t->base + t->sysc);
}
static int __init dmtimer_systimer_type1_reset(struct dmtimer_systimer *t)
{
void __iomem *syss = t->base + OMAP_TIMER_V1_SYS_STAT_OFFSET;
int ret;
u32 l;
dmtimer_systimer_enable(t);
writel_relaxed(BIT(1) | BIT(2), t->base + t->ifctrl);
ret = readl_poll_timeout_atomic(syss, l, l & BIT(0), 100,
DMTIMER_RESET_WAIT);
return ret;
}
/* Note we must use io_base instead of func_base for type2 OCP regs */
static int __init dmtimer_systimer_type2_reset(struct dmtimer_systimer *t)
{
void __iomem *sysc = t->base + t->sysc;
u32 l;
dmtimer_systimer_enable(t);
l = readl_relaxed(sysc);
l |= BIT(0);
writel_relaxed(l, sysc);
return readl_poll_timeout_atomic(sysc, l, !(l & BIT(0)), 100,
DMTIMER_RESET_WAIT);
}
static int __init dmtimer_systimer_reset(struct dmtimer_systimer *t)
{
int ret;
if (dmtimer_systimer_revision1(t))
ret = dmtimer_systimer_type1_reset(t);
else
ret = dmtimer_systimer_type2_reset(t);
if (ret < 0) {
pr_err("%s failed with %i\n", __func__, ret);
return ret;
}
return 0;
}
static const struct of_device_id counter_match_table[] = {
{ .compatible = "ti,omap-counter32k" },
{ /* Sentinel */ },
};
/*
* Check if the SoC als has a usable working 32 KiHz counter. The 32 KiHz
* counter is handled by timer-ti-32k, but we need to detect it as it
* affects the preferred dmtimer system timer configuration. There is
* typically no use for a dmtimer clocksource if the 32 KiHz counter is
* present, except on am437x as described below.
*/
static void __init dmtimer_systimer_check_counter32k(void)
{
struct device_node *np;
if (counter_32k)
return;
np = of_find_matching_node(NULL, counter_match_table);
if (!np) {
counter_32k = -ENODEV;
return;
}
if (of_device_is_available(np))
counter_32k = 1;
else
counter_32k = -ENODEV;
of_node_put(np);
}
static const struct of_device_id dmtimer_match_table[] = {
{ .compatible = "ti,omap2420-timer", },
{ .compatible = "ti,omap3430-timer", },
{ .compatible = "ti,omap4430-timer", },
{ .compatible = "ti,omap5430-timer", },
{ .compatible = "ti,am335x-timer", },
{ .compatible = "ti,am335x-timer-1ms", },
{ .compatible = "ti,dm814-timer", },
{ .compatible = "ti,dm816-timer", },
{ /* Sentinel */ },
};
/*
* Checks that system timers are configured to not reset and idle during
* the generic timer-ti-dm device driver probe. And that the system timer
* source clocks are properly configured. Also, let's not hog any DSP and
* PWM capable timers unnecessarily as system timers.
*/
static bool __init dmtimer_is_preferred(struct device_node *np)
{
if (!of_device_is_available(np))
return false;
if (!of_property_read_bool(np->parent,
"ti,no-reset-on-init"))
return false;
if (!of_property_read_bool(np->parent, "ti,no-idle"))
return false;
/* Secure gptimer12 is always clocked with a fixed source */
if (!of_property_read_bool(np, "ti,timer-secure")) {
if (!of_property_read_bool(np, "assigned-clocks"))
return false;
if (!of_property_read_bool(np, "assigned-clock-parents"))
return false;
}
if (of_property_read_bool(np, "ti,timer-dsp"))
return false;
if (of_property_read_bool(np, "ti,timer-pwm"))
return false;
return true;
}
/*
* Finds the first available usable always-on timer, and assigns it to either
* clockevent or clocksource depending if the counter_32k is available on the
* SoC or not.
*
* Some omap3 boards with unreliable oscillator must not use the counter_32k
* or dmtimer1 with 32 KiHz source. Additionally, the boards with unreliable
* oscillator should really set counter_32k as disabled, and delete dmtimer1
* ti,always-on property, but let's not count on it. For these quirky cases,
* we prefer using the always-on secure dmtimer12 with the internal 32 KiHz
* clock as the clocksource, and any available dmtimer as clockevent.
*
* For am437x, we are using am335x style dmtimer clocksource. It is unclear
* if this quirk handling is really needed, but let's change it separately
* based on testing as it might cause side effects.
*/
static void __init dmtimer_systimer_assign_alwon(void)
{
struct device_node *np;
u32 pa = 0;
bool quirk_unreliable_oscillator = false;
/* Quirk unreliable 32 KiHz oscillator with incomplete dts */
if (of_machine_is_compatible("ti,omap3-beagle-ab4")) {
quirk_unreliable_oscillator = true;
counter_32k = -ENODEV;
}
/* Quirk am437x using am335x style dmtimer clocksource */
if (of_machine_is_compatible("ti,am43"))
counter_32k = -ENODEV;
for_each_matching_node(np, dmtimer_match_table) {
struct resource res;
if (!dmtimer_is_preferred(np))
continue;
if (!of_property_read_bool(np, "ti,timer-alwon"))
continue;
if (of_address_to_resource(np, 0, &res))
continue;
pa = res.start;
/* Quirky omap3 boards must use dmtimer12 */
if (quirk_unreliable_oscillator && pa == 0x48318000)
continue;
of_node_put(np);
break;
}
/* Usually no need for dmtimer clocksource if we have counter32 */
if (counter_32k >= 0) {
clockevent = pa;
clocksource = 0;
} else {
clocksource = pa;
clockevent = DMTIMER_INST_DONT_CARE;
}
}
/* Finds the first usable dmtimer, used for the don't care case */
static u32 __init dmtimer_systimer_find_first_available(void)
{
struct device_node *np;
u32 pa = 0;
for_each_matching_node(np, dmtimer_match_table) {
struct resource res;
if (!dmtimer_is_preferred(np))
continue;
if (of_address_to_resource(np, 0, &res))
continue;
if (res.start == clocksource || res.start == clockevent)
continue;
pa = res.start;
of_node_put(np);
break;
}
return pa;
}
/* Selects the best clocksource and clockevent to use */
static void __init dmtimer_systimer_select_best(void)
{
dmtimer_systimer_check_counter32k();
dmtimer_systimer_assign_alwon();
if (clockevent == DMTIMER_INST_DONT_CARE)
clockevent = dmtimer_systimer_find_first_available();
pr_debug("%s: counter_32k: %i clocksource: %08x clockevent: %08x\n",
__func__, counter_32k, clocksource, clockevent);
}
/* Interface clocks are only available on some SoCs variants */
static int __init dmtimer_systimer_init_clock(struct dmtimer_systimer *t,
struct device_node *np,
const char *name,
unsigned long *rate)
{
struct clk *clock;
unsigned long r;
bool is_ick = false;
int error;
is_ick = !strncmp(name, "ick", 3);
clock = of_clk_get_by_name(np, name);
if ((PTR_ERR(clock) == -EINVAL) && is_ick)
return 0;
else if (IS_ERR(clock))
return PTR_ERR(clock);
error = clk_prepare_enable(clock);
if (error)
return error;
r = clk_get_rate(clock);
if (!r) {
clk_disable_unprepare(clock);
return -ENODEV;
}
if (is_ick)
t->ick = clock;
else
t->fck = clock;
*rate = r;
return 0;
}
static int __init dmtimer_systimer_setup(struct device_node *np,
struct dmtimer_systimer *t)
{
unsigned long rate;
u8 regbase;
int error;
if (!of_device_is_compatible(np->parent, "ti,sysc"))
return -EINVAL;
t->base = of_iomap(np, 0);
if (!t->base)
return -ENXIO;
/*
* Enable optional assigned-clock-parents configured at the timer
* node level. For regular device drivers, this is done automatically
* by bus related code such as platform_drv_probe().
*/
error = of_clk_set_defaults(np, false);
if (error < 0)
pr_err("%s: clock source init failed: %i\n", __func__, error);
/* For ti-sysc, we have timer clocks at the parent module level */
error = dmtimer_systimer_init_clock(t, np->parent, "fck", &rate);
if (error)
goto err_unmap;
t->rate = rate;
error = dmtimer_systimer_init_clock(t, np->parent, "ick", &rate);
if (error)
goto err_unmap;
if (dmtimer_systimer_revision1(t)) {
t->irq_stat = OMAP_TIMER_V1_STAT_OFFSET;
t->irq_ena = OMAP_TIMER_V1_INT_EN_OFFSET;
t->pend = _OMAP_TIMER_WRITE_PEND_OFFSET;
regbase = 0;
} else {
t->irq_stat = OMAP_TIMER_V2_IRQSTATUS;
t->irq_ena = OMAP_TIMER_V2_IRQENABLE_SET;
regbase = OMAP_TIMER_V2_FUNC_OFFSET;
t->pend = regbase + _OMAP_TIMER_WRITE_PEND_OFFSET;
}
t->sysc = OMAP_TIMER_OCP_CFG_OFFSET;
t->load = regbase + _OMAP_TIMER_LOAD_OFFSET;
t->counter = regbase + _OMAP_TIMER_COUNTER_OFFSET;
t->ctrl = regbase + _OMAP_TIMER_CTRL_OFFSET;
t->wakeup = regbase + _OMAP_TIMER_WAKEUP_EN_OFFSET;
t->ifctrl = regbase + _OMAP_TIMER_IF_CTRL_OFFSET;
dmtimer_systimer_reset(t);
dmtimer_systimer_enable(t);
pr_debug("dmtimer rev %08x sysc %08x\n", readl_relaxed(t->base),
readl_relaxed(t->base + t->sysc));
return 0;
err_unmap:
iounmap(t->base);
return error;
}
/* Clockevent */
static struct dmtimer_clockevent *
to_dmtimer_clockevent(struct clock_event_device *clockevent)
{
return container_of(clockevent, struct dmtimer_clockevent, dev);
}
static irqreturn_t dmtimer_clockevent_interrupt(int irq, void *data)
{
struct dmtimer_clockevent *clkevt = data;
struct dmtimer_systimer *t = &clkevt->t;
writel_relaxed(OMAP_TIMER_INT_OVERFLOW, t->base + t->irq_stat);
clkevt->dev.event_handler(&clkevt->dev);
return IRQ_HANDLED;
}
static int dmtimer_set_next_event(unsigned long cycles,
struct clock_event_device *evt)
{
struct dmtimer_clockevent *clkevt = to_dmtimer_clockevent(evt);
struct dmtimer_systimer *t = &clkevt->t;
void __iomem *pend = t->base + t->pend;
while (readl_relaxed(pend) & WP_TCRR)
cpu_relax();
writel_relaxed(0xffffffff - cycles, t->base + t->counter);
while (readl_relaxed(pend) & WP_TCLR)
cpu_relax();
writel_relaxed(OMAP_TIMER_CTRL_ST, t->base + t->ctrl);
return 0;
}
static int dmtimer_clockevent_shutdown(struct clock_event_device *evt)
{
struct dmtimer_clockevent *clkevt = to_dmtimer_clockevent(evt);
struct dmtimer_systimer *t = &clkevt->t;
void __iomem *ctrl = t->base + t->ctrl;
u32 l;
l = readl_relaxed(ctrl);
if (l & OMAP_TIMER_CTRL_ST) {
l &= ~BIT(0);
writel_relaxed(l, ctrl);
/* Flush posted write */
l = readl_relaxed(ctrl);
/* Wait for functional clock period x 3.5 */
udelay(3500000 / t->rate + 1);
}
writel_relaxed(OMAP_TIMER_INT_OVERFLOW, t->base + t->irq_stat);
return 0;
}
static int dmtimer_set_periodic(struct clock_event_device *evt)
{
struct dmtimer_clockevent *clkevt = to_dmtimer_clockevent(evt);
struct dmtimer_systimer *t = &clkevt->t;
void __iomem *pend = t->base + t->pend;
dmtimer_clockevent_shutdown(evt);
/* Looks like we need to first set the load value separately */
while (readl_relaxed(pend) & WP_TLDR)
cpu_relax();
writel_relaxed(clkevt->period, t->base + t->load);
while (readl_relaxed(pend) & WP_TCRR)
cpu_relax();
writel_relaxed(clkevt->period, t->base + t->counter);
while (readl_relaxed(pend) & WP_TCLR)
cpu_relax();
writel_relaxed(OMAP_TIMER_CTRL_AR | OMAP_TIMER_CTRL_ST,
t->base + t->ctrl);
return 0;
}
static void omap_clockevent_idle(struct clock_event_device *evt)
{
struct dmtimer_clockevent *clkevt = to_dmtimer_clockevent(evt);
struct dmtimer_systimer *t = &clkevt->t;
dmtimer_systimer_disable(t);
clk_disable(t->fck);
}
static void omap_clockevent_unidle(struct clock_event_device *evt)
{
struct dmtimer_clockevent *clkevt = to_dmtimer_clockevent(evt);
struct dmtimer_systimer *t = &clkevt->t;
int error;
error = clk_enable(t->fck);
if (error)
pr_err("could not enable timer fck on resume: %i\n", error);
dmtimer_systimer_enable(t);
writel_relaxed(OMAP_TIMER_INT_OVERFLOW, t->base + t->irq_ena);
writel_relaxed(OMAP_TIMER_INT_OVERFLOW, t->base + t->wakeup);
}
static int __init dmtimer_clkevt_init_common(struct dmtimer_clockevent *clkevt,
struct device_node *np,
unsigned int features,
const struct cpumask *cpumask,
const char *name,
int rating)
{
struct clock_event_device *dev;
struct dmtimer_systimer *t;
int error;
t = &clkevt->t;
dev = &clkevt->dev;
/*
* We mostly use cpuidle_coupled with ARM local timers for runtime,
* so there's probably no use for CLOCK_EVT_FEAT_DYNIRQ here.
*/
dev->features = features;
dev->rating = rating;
dev->set_next_event = dmtimer_set_next_event;
dev->set_state_shutdown = dmtimer_clockevent_shutdown;
dev->set_state_periodic = dmtimer_set_periodic;
dev->set_state_oneshot = dmtimer_clockevent_shutdown;
dev->set_state_oneshot_stopped = dmtimer_clockevent_shutdown;
dev->tick_resume = dmtimer_clockevent_shutdown;
dev->cpumask = cpumask;
dev->irq = irq_of_parse_and_map(np, 0);
if (!dev->irq)
return -ENXIO;
error = dmtimer_systimer_setup(np, &clkevt->t);
if (error)
return error;
clkevt->period = 0xffffffff - DIV_ROUND_CLOSEST(t->rate, HZ);
/*
* For clock-event timers we never read the timer counter and
* so we are not impacted by errata i103 and i767. Therefore,
* we can safely ignore this errata for clock-event timers.
*/
writel_relaxed(OMAP_TIMER_CTRL_POSTED, t->base + t->ifctrl);
error = request_irq(dev->irq, dmtimer_clockevent_interrupt,
IRQF_TIMER, name, clkevt);
if (error)
goto err_out_unmap;
writel_relaxed(OMAP_TIMER_INT_OVERFLOW, t->base + t->irq_ena);
writel_relaxed(OMAP_TIMER_INT_OVERFLOW, t->base + t->wakeup);
pr_info("TI gptimer %s: %s%lu Hz at %pOF\n",
name, of_property_read_bool(np, "ti,timer-alwon") ?
"always-on " : "", t->rate, np->parent);
return 0;
err_out_unmap:
iounmap(t->base);
return error;
}
static int __init dmtimer_clockevent_init(struct device_node *np)
{
struct dmtimer_clockevent *clkevt;
int error;
clkevt = kzalloc(sizeof(*clkevt), GFP_KERNEL);
if (!clkevt)
return -ENOMEM;
error = dmtimer_clkevt_init_common(clkevt, np,
CLOCK_EVT_FEAT_PERIODIC |
CLOCK_EVT_FEAT_ONESHOT,
cpu_possible_mask, "clockevent",
300);
if (error)
goto err_out_free;
clockevents_config_and_register(&clkevt->dev, clkevt->t.rate,
3, /* Timer internal resync latency */
0xffffffff);
if (of_machine_is_compatible("ti,am33xx") ||
of_machine_is_compatible("ti,am43")) {
clkevt->dev.suspend = omap_clockevent_idle;
clkevt->dev.resume = omap_clockevent_unidle;
}
return 0;
err_out_free:
kfree(clkevt);
return error;
}
/* Dmtimer as percpu timer. See dra7 ARM architected timer wrap erratum i940 */
static DEFINE_PER_CPU(struct dmtimer_clockevent, dmtimer_percpu_timer);
static int __init dmtimer_percpu_timer_init(struct device_node *np, int cpu)
{
struct dmtimer_clockevent *clkevt;
int error;
if (!cpu_possible(cpu))
return -EINVAL;
if (!of_property_read_bool(np->parent, "ti,no-reset-on-init") ||
!of_property_read_bool(np->parent, "ti,no-idle"))
pr_warn("Incomplete dtb for percpu dmtimer %pOF\n", np->parent);
clkevt = per_cpu_ptr(&dmtimer_percpu_timer, cpu);
error = dmtimer_clkevt_init_common(clkevt, np, CLOCK_EVT_FEAT_ONESHOT,
cpumask_of(cpu), "percpu-dmtimer",
500);
if (error)
return error;
return 0;
}
/* See TRM for timer internal resynch latency */
static int omap_dmtimer_starting_cpu(unsigned int cpu)
{
struct dmtimer_clockevent *clkevt = per_cpu_ptr(&dmtimer_percpu_timer, cpu);
struct clock_event_device *dev = &clkevt->dev;
struct dmtimer_systimer *t = &clkevt->t;
clockevents_config_and_register(dev, t->rate, 3, ULONG_MAX);
irq_force_affinity(dev->irq, cpumask_of(cpu));
return 0;
}
static int __init dmtimer_percpu_timer_startup(void)
{
struct dmtimer_clockevent *clkevt = per_cpu_ptr(&dmtimer_percpu_timer, 0);
struct dmtimer_systimer *t = &clkevt->t;
if (t->sysc) {
cpuhp_setup_state(CPUHP_AP_TI_GP_TIMER_STARTING,
"clockevents/omap/gptimer:starting",
omap_dmtimer_starting_cpu, NULL);
}
return 0;
}
subsys_initcall(dmtimer_percpu_timer_startup);
static int __init dmtimer_percpu_quirk_init(struct device_node *np, u32 pa)
{
struct device_node *arm_timer;
arm_timer = of_find_compatible_node(NULL, NULL, "arm,armv7-timer");
if (of_device_is_available(arm_timer)) {
pr_warn_once("ARM architected timer wrap issue i940 detected\n");
return 0;
}
if (pa == 0x4882c000) /* dra7 dmtimer15 */
return dmtimer_percpu_timer_init(np, 0);
else if (pa == 0x4882e000) /* dra7 dmtimer16 */
return dmtimer_percpu_timer_init(np, 1);
return 0;
}
/* Clocksource */
static struct dmtimer_clocksource *
to_dmtimer_clocksource(struct clocksource *cs)
{
return container_of(cs, struct dmtimer_clocksource, dev);
}
static u64 dmtimer_clocksource_read_cycles(struct clocksource *cs)
{
struct dmtimer_clocksource *clksrc = to_dmtimer_clocksource(cs);
struct dmtimer_systimer *t = &clksrc->t;
return (u64)readl_relaxed(t->base + t->counter);
}
static void __iomem *dmtimer_sched_clock_counter;
static u64 notrace dmtimer_read_sched_clock(void)
{
return readl_relaxed(dmtimer_sched_clock_counter);
}
static void dmtimer_clocksource_suspend(struct clocksource *cs)
{
struct dmtimer_clocksource *clksrc = to_dmtimer_clocksource(cs);
struct dmtimer_systimer *t = &clksrc->t;
clksrc->loadval = readl_relaxed(t->base + t->counter);
dmtimer_systimer_disable(t);
clk_disable(t->fck);
}
static void dmtimer_clocksource_resume(struct clocksource *cs)
{
struct dmtimer_clocksource *clksrc = to_dmtimer_clocksource(cs);
struct dmtimer_systimer *t = &clksrc->t;
int error;
error = clk_enable(t->fck);
if (error)
pr_err("could not enable timer fck on resume: %i\n", error);
dmtimer_systimer_enable(t);
writel_relaxed(clksrc->loadval, t->base + t->counter);
writel_relaxed(OMAP_TIMER_CTRL_ST | OMAP_TIMER_CTRL_AR,
t->base + t->ctrl);
}
static int __init dmtimer_clocksource_init(struct device_node *np)
{
struct dmtimer_clocksource *clksrc;
struct dmtimer_systimer *t;
struct clocksource *dev;
int error;
clksrc = kzalloc(sizeof(*clksrc), GFP_KERNEL);
if (!clksrc)
return -ENOMEM;
dev = &clksrc->dev;
t = &clksrc->t;
error = dmtimer_systimer_setup(np, t);
if (error)
goto err_out_free;
dev->name = "dmtimer";
dev->rating = 300;
dev->read = dmtimer_clocksource_read_cycles;
dev->mask = CLOCKSOURCE_MASK(32);
dev->flags = CLOCK_SOURCE_IS_CONTINUOUS;
/* Unlike for clockevent, legacy code sets suspend only for am4 */
if (of_machine_is_compatible("ti,am43")) {
dev->suspend = dmtimer_clocksource_suspend;
dev->resume = dmtimer_clocksource_resume;
}
writel_relaxed(0, t->base + t->counter);
writel_relaxed(OMAP_TIMER_CTRL_ST | OMAP_TIMER_CTRL_AR,
t->base + t->ctrl);
pr_info("TI gptimer clocksource: %s%pOF\n",
of_property_read_bool(np, "ti,timer-alwon") ?
"always-on " : "", np->parent);
if (!dmtimer_sched_clock_counter) {
dmtimer_sched_clock_counter = t->base + t->counter;
sched_clock_register(dmtimer_read_sched_clock, 32, t->rate);
}
if (clocksource_register_hz(dev, t->rate))
pr_err("Could not register clocksource %pOF\n", np);
return 0;
err_out_free:
kfree(clksrc);
return -ENODEV;
}
/*
* To detect between a clocksource and clockevent, we assume the device tree
* has no interrupts configured for a clocksource timer.
*/
static int __init dmtimer_systimer_init(struct device_node *np)
{
struct resource res;
u32 pa;
/* One time init for the preferred timer configuration */
if (!clocksource && !clockevent)
dmtimer_systimer_select_best();
if (!clocksource && !clockevent) {
pr_err("%s: unable to detect system timers, update dtb?\n",
__func__);
return -EINVAL;
}
of_address_to_resource(np, 0, &res);
pa = (u32)res.start;
if (!pa)
return -EINVAL;
if (counter_32k <= 0 && clocksource == pa)
return dmtimer_clocksource_init(np);
if (clockevent == pa)
return dmtimer_clockevent_init(np);
if (of_machine_is_compatible("ti,dra7"))
return dmtimer_percpu_quirk_init(np, pa);
return 0;
}
TIMER_OF_DECLARE(systimer_omap2, "ti,omap2420-timer", dmtimer_systimer_init);
TIMER_OF_DECLARE(systimer_omap3, "ti,omap3430-timer", dmtimer_systimer_init);
TIMER_OF_DECLARE(systimer_omap4, "ti,omap4430-timer", dmtimer_systimer_init);
TIMER_OF_DECLARE(systimer_omap5, "ti,omap5430-timer", dmtimer_systimer_init);
TIMER_OF_DECLARE(systimer_am33x, "ti,am335x-timer", dmtimer_systimer_init);
TIMER_OF_DECLARE(systimer_am3ms, "ti,am335x-timer-1ms", dmtimer_systimer_init);
TIMER_OF_DECLARE(systimer_dm814, "ti,dm814-timer", dmtimer_systimer_init);
TIMER_OF_DECLARE(systimer_dm816, "ti,dm816-timer", dmtimer_systimer_init);