99 lines
2.6 KiB
Plaintext
99 lines
2.6 KiB
Plaintext
RT5682 audio CODEC
|
|
|
|
This device supports I2C only.
|
|
|
|
Required properties:
|
|
|
|
- compatible : "realtek,rt5682" or "realtek,rt5682i"
|
|
|
|
- reg : The I2C address of the device.
|
|
|
|
- AVDD-supply: phandle to the regulator supplying analog power through the
|
|
AVDD pin
|
|
|
|
- MICVDD-supply: phandle to the regulator supplying power for the microphone
|
|
bias through the MICVDD pin. Either MICVDD or VBAT should be present.
|
|
|
|
- VBAT-supply: phandle to the regulator supplying battery power through the
|
|
VBAT pin. Either MICVDD or VBAT should be present.
|
|
|
|
- DBVDD-supply: phandle to the regulator supplying I/O power through the DBVDD
|
|
pin.
|
|
|
|
- LDO1-IN-supply: phandle to the regulator supplying power to the digital core
|
|
and charge pump through the LDO1_IN pin.
|
|
|
|
Optional properties:
|
|
|
|
- interrupts : The CODEC's interrupt output.
|
|
|
|
- realtek,dmic1-data-pin
|
|
0: dmic1 is not used
|
|
1: using GPIO2 pin as dmic1 data pin
|
|
2: using GPIO5 pin as dmic1 data pin
|
|
|
|
- realtek,dmic1-clk-pin
|
|
0: using GPIO1 pin as dmic1 clock pin
|
|
1: using GPIO3 pin as dmic1 clock pin
|
|
|
|
- realtek,jd-src
|
|
0: No JD is used
|
|
1: using JD1 as JD source
|
|
|
|
- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
|
|
|
|
- realtek,btndet-delay
|
|
The debounce delay for push button.
|
|
The delay time is realtek,btndet-delay value multiple of 8.192 ms.
|
|
If absent, the default is 16.
|
|
|
|
- #clock-cells : Should be set to '<1>', wclk and bclk sources provided.
|
|
- clock-output-names : Name given for DAI clocks output.
|
|
|
|
- clocks : phandle and clock specifier for codec MCLK.
|
|
- clock-names : Clock name string for 'clocks' attribute, should be "mclk".
|
|
|
|
- realtek,dmic-clk-rate-hz : Set the clock rate (hz) for the requirement of
|
|
the particular DMIC.
|
|
|
|
- realtek,dmic-delay-ms : Set the delay time (ms) for the requirement of
|
|
the particular DMIC.
|
|
|
|
- realtek,dmic-clk-driving-high : Set the high driving of the DMIC clock out.
|
|
|
|
- #sound-dai-cells: Should be set to '<1>'.
|
|
|
|
Pins on the device (for linking into audio routes) for RT5682:
|
|
|
|
* DMIC L1
|
|
* DMIC R1
|
|
* IN1P
|
|
* HPOL
|
|
* HPOR
|
|
|
|
Example:
|
|
|
|
rt5682 {
|
|
compatible = "realtek,rt5682i";
|
|
reg = <0x1a>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_LEVEL_HIGH>;
|
|
realtek,ldo1-en-gpios =
|
|
<&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_HIGH>;
|
|
realtek,dmic1-data-pin = <1>;
|
|
realtek,dmic1-clk-pin = <1>;
|
|
realtek,jd-src = <1>;
|
|
realtek,btndet-delay = <16>;
|
|
|
|
#clock-cells = <1>;
|
|
clock-output-names = "rt5682-dai-wclk", "rt5682-dai-bclk";
|
|
|
|
clocks = <&osc>;
|
|
clock-names = "mclk";
|
|
|
|
AVDD-supply = <&avdd_reg>;
|
|
MICVDD-supply = <&micvdd_reg>;
|
|
DBVDD-supply = <&dbvdd_reg>;
|
|
LDO1-IN-supply = <&ldo1_in_reg>;
|
|
};
|