139 lines
3.1 KiB
C
139 lines
3.1 KiB
C
|
// SPDX-License-Identifier: GPL-2.0-or-later
|
||
|
|
/*
|
||
|
|
* (c) 1998 Grant R. Guenther <grant@torque.net>
|
||
|
|
*
|
||
|
|
* fit2.c is a low-level protocol driver for the older version
|
||
|
|
* of the Fidelity International Technology parallel port adapter.
|
||
|
|
* This adapter is used in their TransDisk 2000 and older TransDisk
|
||
|
|
* 3000 portable hard-drives. As far as I can tell, this device
|
||
|
|
* supports 4-bit mode _only_.
|
||
|
|
*
|
||
|
|
* Newer models of the FIT products use an enhanced protocol.
|
||
|
|
* The "fit3" protocol module should support current drives.
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <linux/module.h>
|
||
|
|
#include <linux/init.h>
|
||
|
|
#include <linux/delay.h>
|
||
|
|
#include <linux/kernel.h>
|
||
|
|
#include <linux/types.h>
|
||
|
|
#include <linux/wait.h>
|
||
|
|
#include <asm/io.h>
|
||
|
|
#include "pata_parport.h"
|
||
|
|
|
||
|
|
#define j44(a, b) (((a >> 4) & 0x0f) | (b & 0xf0))
|
||
|
|
|
||
|
|
/*
|
||
|
|
* cont = 0 - access the IDE register file
|
||
|
|
* cont = 1 - access the IDE command set
|
||
|
|
*
|
||
|
|
* NB: The FIT adapter does not appear to use the control registers.
|
||
|
|
* So, we map ALT_STATUS to STATUS and NO-OP writes to the device
|
||
|
|
* control register - this means that IDE reset will not work on these
|
||
|
|
* devices.
|
||
|
|
*/
|
||
|
|
|
||
|
|
static void fit2_write_regr(struct pi_adapter *pi, int cont, int regr, int val)
|
||
|
|
{
|
||
|
|
if (cont == 1)
|
||
|
|
return;
|
||
|
|
w2(0xc); w0(regr); w2(4); w0(val); w2(5); w0(0); w2(4);
|
||
|
|
}
|
||
|
|
|
||
|
|
static int fit2_read_regr(struct pi_adapter *pi, int cont, int regr)
|
||
|
|
{
|
||
|
|
int a, b, r;
|
||
|
|
|
||
|
|
if (cont) {
|
||
|
|
if (regr != 6)
|
||
|
|
return 0xff;
|
||
|
|
r = 7;
|
||
|
|
} else {
|
||
|
|
r = regr + 0x10;
|
||
|
|
}
|
||
|
|
|
||
|
|
w2(0xc); w0(r); w2(4); w2(5);
|
||
|
|
w0(0); a = r1();
|
||
|
|
w0(1); b = r1();
|
||
|
|
w2(4);
|
||
|
|
|
||
|
|
return j44(a, b);
|
||
|
|
}
|
||
|
|
|
||
|
|
static void fit2_read_block(struct pi_adapter *pi, char *buf, int count)
|
||
|
|
{
|
||
|
|
int k, a, b, c, d;
|
||
|
|
|
||
|
|
w2(0xc); w0(0x10);
|
||
|
|
|
||
|
|
for (k = 0; k < count / 4; k++) {
|
||
|
|
w2(4); w2(5);
|
||
|
|
w0(0); a = r1(); w0(1); b = r1();
|
||
|
|
w0(3); c = r1(); w0(2); d = r1();
|
||
|
|
buf[4 * k + 0] = j44(a, b);
|
||
|
|
buf[4 * k + 1] = j44(d, c);
|
||
|
|
|
||
|
|
w2(4); w2(5);
|
||
|
|
a = r1(); w0(3); b = r1();
|
||
|
|
w0(1); c = r1(); w0(0); d = r1();
|
||
|
|
buf[4 * k + 2] = j44(d, c);
|
||
|
|
buf[4 * k + 3] = j44(a, b);
|
||
|
|
}
|
||
|
|
|
||
|
|
w2(4);
|
||
|
|
}
|
||
|
|
|
||
|
|
static void fit2_write_block(struct pi_adapter *pi, char *buf, int count)
|
||
|
|
{
|
||
|
|
int k;
|
||
|
|
|
||
|
|
w2(0xc); w0(0);
|
||
|
|
for (k = 0; k < count / 2; k++) {
|
||
|
|
w2(4); w0(buf[2 * k]);
|
||
|
|
w2(5); w0(buf[2 * k + 1]);
|
||
|
|
}
|
||
|
|
w2(4);
|
||
|
|
}
|
||
|
|
|
||
|
|
static void fit2_connect(struct pi_adapter *pi)
|
||
|
|
{
|
||
|
|
pi->saved_r0 = r0();
|
||
|
|
pi->saved_r2 = r2();
|
||
|
|
w2(0xcc);
|
||
|
|
}
|
||
|
|
|
||
|
|
static void fit2_disconnect(struct pi_adapter *pi)
|
||
|
|
{
|
||
|
|
w0(pi->saved_r0);
|
||
|
|
w2(pi->saved_r2);
|
||
|
|
}
|
||
|
|
|
||
|
|
static void fit2_log_adapter(struct pi_adapter *pi)
|
||
|
|
{
|
||
|
|
dev_info(&pi->dev, "FIT 2000 adapter at 0x%x, delay %d\n",
|
||
|
|
pi->port, pi->delay);
|
||
|
|
|
||
|
|
}
|
||
|
|
|
||
|
|
static struct pi_protocol fit2 = {
|
||
|
|
.owner = THIS_MODULE,
|
||
|
|
.name = "fit2",
|
||
|
|
.max_mode = 1,
|
||
|
|
.epp_first = 2,
|
||
|
|
.default_delay = 1,
|
||
|
|
.max_units = 1,
|
||
|
|
.write_regr = fit2_write_regr,
|
||
|
|
.read_regr = fit2_read_regr,
|
||
|
|
.write_block = fit2_write_block,
|
||
|
|
.read_block = fit2_read_block,
|
||
|
|
.connect = fit2_connect,
|
||
|
|
.disconnect = fit2_disconnect,
|
||
|
|
.log_adapter = fit2_log_adapter,
|
||
|
|
};
|
||
|
|
|
||
|
|
MODULE_LICENSE("GPL");
|
||
|
|
MODULE_AUTHOR("Grant R. Guenther <grant@torque.net>");
|
||
|
|
MODULE_DESCRIPTION("Fidelity International Technology parallel port IDE adapter"
|
||
|
|
"(older models) protocol driver");
|
||
|
|
module_pata_parport_driver(fit2);
|